Routers / Switches :: Internet Access To LAN Network Not Stable?

May 18, 2011

I have 12 computers in Local Area Network, I am using 3MB DSL broadband, all PC using XP SP3 connected through D-Link Switch with IP address 192.168.0.201 to 192.168.0.212, The D-Link router gateway is 192.168.0.1Network diagram is as followsADSL modemouterIPC1, PC2, upto PC 12My problems are.1. All PC cannot access Internet, So I reset the modem, wait for a few minutes, if I am lucky, Internet comes back, sometimes have to wait longer 15mins or 30 mins2. PC12 is used for monitoring, but cannot see PC 1, the rest can see.When I try to ping, time out, but after sometimes....it came back, I can see PC 1, then disappear again.How do I solve this problems?Note, the ADSL modem provided by the Service provider looks normal, with Power, Ethernet and DSL lights ON.

View 15 Replies

Routers / Switches :: Access Internet But Not Network

Jan 16, 2011

I am able to access the internet. I am running Windows 7 on my laptop and have a wired connection between it and my intergrated router. The internet works fine, but it seems to think that I am not connected to the network. I'm not certain it realized that I even had a network, since when I try to activate media sharing it just gets stuck at "Identifying Network". The whole purpose of this is to be able to play music from my computer on my Xbox 360, alternative solutions for this goal would be good too.

View 5 Replies View Related

Routers / Switches :: Setup A Vlan To Access Internet Not Network?

Nov 7, 2011

I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.

View 5 Replies View Related

Routers / Switches :: Setup Internet Access And Intranet Access Using Two Cards Per PC?

Mar 29, 2011

I am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.

View 6 Replies View Related

Routers / Switches :: No Internet Access On Third Router?

Oct 20, 2012

I have High Speed Charter Internet going to a modem in form of coaxial cable with one Ethernet port available and one coaxial connection for TV and a phone jack. I have that Ethernet port connected to a:Motorola Wireless Modem[CODE]

View 4 Replies View Related

Routers / Switches :: Unable To Access Internet Through Router?

Feb 3, 2013

Lost connection to Internet though router appears normal. Belkin router, MacBook.

View 1 Replies View Related

Routers / Switches :: Block Only Internet Access From Firewall?

Sep 25, 2012

i want block only internet access from firewall

View 1 Replies View Related

Routers / Switches :: Internet Access Over LAN Blocked But Connected

Sep 16, 2011

We are having a workgroup of 12 Pc connected using a switch (hub) having all Windows XP SP2 and some of them registered Kayspersky antivirus 2011. We have internet access using D-Link 2460T (DSL wireless ADSL router) connected to our LAN using a network wire and having DHCP enabled. Everything was working well for 4-5 years but recently a problem appeared.

[code]...

View 10 Replies View Related

Routers / Switches :: Netgear Wireless (wgr614v9) - No Internet Access?

Jul 2, 2012

My netgear wireless router (wgr614v9) wont reboot or let me access the internet what should i do.

View 2 Replies View Related

Routers / Switches :: Can't Share Internet Access From Cisco Switch

Apr 15, 2011

I went out and bought a linksys 5 port workgroup switch. I tried to hook my internet into it and my other computers into it , THINKING, I would be able to get internet on all. No go. I can get inter net on one, as you can tell. but all others nothing. and to make matters worse i got win 2000, win xp pro, and linux that I like to get online.. I have : renewed IP's assin Ip's refresh, purge dns. rebooted. all and rebooted in diferent orders. double checked connections, tested all lines. The network is on a rj45 ethernet .

View 1 Replies View Related

Routers / Switches :: Upgrade D-link Router To Get Faster Internet Access?

Jan 3, 2012

I have a DI-604 D-link router, is it necessay to upgrade to newer router to get faster access to internet? Upgrade Firmware? I have a PD950 processor with Win XP pro and use it for DAYTRADING streaming data and fast executions.

View 5 Replies View Related

Routers / Switches :: Netgear Fs605 Ethernet - Wifi Printer Access In Network?

Apr 5, 2013

I use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.

View 1 Replies View Related

Routers / Switches :: Wireless Only Supplies Half The House With Consistent Internet Access?

Jan 25, 2012

My wireless router only supplies half the house with consistent Internet access. What's the easiest way to ensure connectivity throughout the house?

View 1 Replies View Related

Routers / Switches :: How To Find The Network Security Key To Internet Modem

Jan 12, 2012

How do I find my network security key for my cisco e1000 router if the computer that it is installed on is broken?

View 1 Replies View Related

Routers / Switches :: No Internet On 2nd Router Installed On Home Network?

Mar 23, 2012

I have 2 linksys routers installed on my home network. The primary router is a linksys WRT360n and is stationed inside the main home, while the 2nd is a linksys WRT160N located in my office. I've connected them via the lan to lan configuration and have disabled DHCP server on the 2nd. I can access the 2nd router via my primary PC but am unable to access the internet or see the primary from the PC connected to the 2nd router.

View 3 Replies View Related

Routers / Switches :: Cannot Enable Users On Network To Connect To Internet

Jan 24, 2013

when I try to enable network internet connection on my computer it tells me that somebody else is using IP 192.168.0.1

View 2 Replies View Related

Cisco Routers :: QuickVPN To RV082 No Longer Stable

Sep 11, 2011

I have a RV082 in the corporate office, and several remote people connecting to it using QuickVPN through a variety of clients (XP and Windows 7). As of today, they are all now seeing the "Remote Gateway is not responding - disconnect or wait" message. Checking through the logs on some of the remote clients, I see the "Failed to ping the remote router" message several times, followed by the "Ping was blocked, which can be caused by an unexpected disconnect." message.

The odd thing is that everyone has been running very well over the past 2-3 weeks - most people with 8+ hours of solid connectivity. We made no changes to the clients, nor to the remote router in the corporate office.

View 3 Replies View Related

Broadband Internet Not Stable

Nov 1, 2012

my prepaid broadband connection always drops to 0 every after 30s - 1min. It increases its speed only if I load a page or download, after finish loading, speed drops again to 0.

View 6 Replies View Related

D-Link DIR-655 :: Setting Up As Stable Router For Network?

Dec 16, 2011

I bought a DIR-655 today so i can port trigger to all my xbox's instead of only being able to port forward to 1 xbox from my Netgear CGD24N. My problem is setting up a stable network that wont drop out.

What i am trying to set up: Internet --> Modem (Netgear CGD24N) <---> Router <---> Everything else (2 Xbox's, 5 Computers, Phone's)

I have one ethernet cord from my netgear to the internet port in my D-Link. Is that correct?

They are both set to DHCP as that is the only way i have been able to create a network that i can connect to the net through my router. Problem is it is constantly reconnecting and only getting speeds of 2mb dl and 1mb up. (I should be getting speeds of 30mb dl, 2mb up.)

View 1 Replies View Related

D-Link DIR-655 :: Internet Connection Faster But Now Less Stable?

Sep 17, 2011

About two weeks ago, my internet connection became faster. I am not sure if it has to do with my cable ISP doing something or something I did with my computer.

Right around the same time, my connection began disconnecting every two or three days. Before this, I had a rock solid connection for two years.

It will usually reconnect after a minute. Otherwise, when I boot my computer, the problem is solved.

I am certain there is a correlation between the connection speed going up and my connection becoming less stable.

View 6 Replies View Related

Routers / Switches :: Setup An Home Network With A Wireless Router And Use Multiple Switches?

Jan 29, 2011

I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.

View 3 Replies View Related

Cisco Routers :: RVS4000 Losing Internet And Network Access / Restart Required

Nov 27, 2012

I have recently purchased a RVS4000 router and am experiencing major downtime.Almost everyday the RVS4000 router losing internet connectivity. I noticed that when this happens I cannot login into the router from my pc which is connected to the RVS4000 network.The only way to restore connectivity is to restart the RVS4000 by disconnecting power and powering back up.The router's WAN is connected to my Cable modem.The RVS400 has two PC connected to it. (port 3 & 4) I have a Cisco 8-port switch connect to the RVS4000 with 3 additional PCs/devices on it.

View 6 Replies View Related

Routers / Switches :: Configure Two GB Routers On The Same Network?

Jul 26, 2012

I have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.

View 10 Replies View Related

Routers / Switches :: How To Connect 2 Routers On A Network

Jan 19, 2011

how to connect 2 routers on different lan

View 3 Replies View Related

Routers / Switches :: How To Bridge Two Routers Over The Internet

Apr 26, 2012

i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?

View 5 Replies View Related

Routers / Switches :: How To Connect Two Internet Routers To One LAN

Mar 8, 2011

How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.

If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?

View 5 Replies View Related

Cisco Switches :: SG-200 Access Point Is Only Able To Access Internet / When It Is Plugged Into Port

Jun 22, 2012

I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]

View 4 Replies View Related

Routers / Switches :: Can't Access Linksys With 192.168.1.1

Mar 29, 2013

I have windows 7 could this be the problem? it is unsecure and I have access the security part of it

View 1 Replies View Related

Home Network :: How To Stop Internet Access Through Network Complete Internet Access

Jan 26, 2012

i would like to know that how to stop internet access through network complete internet access

View 2 Replies View Related

Routers / Switches :: Remote Desktop Access From It?

Mar 7, 2012

how can I remote in to my router and I need to get past my router to my pc desktop

View 2 Replies View Related

Routers / Switches :: Can't Access 192.168.1.1 Using Admin ID And Password

Mar 29, 2013

what to do with my router cdr -king i cant access 192.168.1.1 in second time. i access it for the first time but i forgot to configure password now i cant connect using ID:admin Pass:admin

View 2 Replies View Related

Routers / Switches :: Can't Access Any Https Sites

Oct 25, 2011

when my Linux VM is running!How's this for a mystery - last night I noticed that I could no longer access my gmail. Thought it might be down. This morning, I still couldn't access it. Thought I would try comcast, no joy either. Changed computers, no difference. Changed routers, no difference. Bought a new router and started plugging in network cables one at a time. My main machine first, everything works - http and https sites, a second computer, all good. The switch. Fine. Powerline. Still good. Then I plug in a Windows server running a Linux VM. Https sites on all the other machines stop working. Pause the Linux VM, restart router - https sites return to life. Went to Linux machine, re-enabled ipv6 (the only recent change on the Linux machine was to disable ipv6 since upon a reboot, Linux didn't have an ipv4 address). Restart Linux everything seems fine. A few hours go by, try to connect my wife's new laptop and at that moment wireless seems to stop. Restart router, wireless is back. But lo and behold, https is gone again. Unplug the machine that has the Linux VM, restart router, all is good.Ever see anything this weird?