Routers / Switches :: Access Internet But Not Network
Jan 16, 2011
I am able to access the internet. I am running Windows 7 on my laptop and have a wired connection between it and my intergrated router. The internet works fine, but it seems to think that I am not connected to the network. I'm not certain it realized that I even had a network, since when I try to activate media sharing it just gets stuck at "Identifying Network". The whole purpose of this is to be able to play music from my computer on my Xbox 360, alternative solutions for this goal would be good too.
I have 12 computers in Local Area Network, I am using 3MB DSL broadband, all PC using XP SP3 connected through D-Link Switch with IP address 192.168.0.201 to 192.168.0.212, The D-Link router gateway is 192.168.0.1Network diagram is as followsADSL modemouterIPC1, PC2, upto PC 12My problems are.1. All PC cannot access Internet, So I reset the modem, wait for a few minutes, if I am lucky, Internet comes back, sometimes have to wait longer 15mins or 30 mins2. PC12 is used for monitoring, but cannot see PC 1, the rest can see.When I try to ping, time out, but after sometimes....it came back, I can see PC 1, then disappear again.How do I solve this problems?Note, the ADSL modem provided by the Service provider looks normal, with Power, Ethernet and DSL lights ON.
I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
I am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
I have High Speed Charter Internet going to a modem in form of coaxial cable with one Ethernet port available and one coaxial connection for TV and a phone jack. I have that Ethernet port connected to a:Motorola Wireless Modem[CODE]
We are having a workgroup of 12 Pc connected using a switch (hub) having all Windows XP SP2 and some of them registered Kayspersky antivirus 2011. We have internet access using D-Link 2460T (DSL wireless ADSL router) connected to our LAN using a network wire and having DHCP enabled. Everything was working well for 4-5 years but recently a problem appeared.
I went out and bought a linksys 5 port workgroup switch. I tried to hook my internet into it and my other computers into it , THINKING, I would be able to get internet on all. No go. I can get inter net on one, as you can tell. but all others nothing. and to make matters worse i got win 2000, win xp pro, and linux that I like to get online.. I have : renewed IP's assin Ip's refresh, purge dns. rebooted. all and rebooted in diferent orders. double checked connections, tested all lines. The network is on a rj45 ethernet .
I have a DI-604 D-link router, is it necessay to upgrade to newer router to get faster access to internet? Upgrade Firmware? I have a PD950 processor with Win XP pro and use it for DAYTRADING streaming data and fast executions.
I use a Netgear FS605 Ethernet Switch to connect a wifi modem to my network and thus to the internet. People in that room can jump online via the wifi modem. You can also print to the wireless printer in that room via that wifi modem being local. However, I can no longer print to the wifi printer from anywhere else in my network (I could before I got a new router and wifi modem in there).Would this be a problem with this Switch or with the modem e.g.
I have 2 linksys routers installed on my home network. The primary router is a linksys WRT360n and is stationed inside the main home, while the 2nd is a linksys WRT160N located in my office. I've connected them via the lan to lan configuration and have disabled DHCP server on the 2nd. I can access the 2nd router via my primary PC but am unable to access the internet or see the primary from the PC connected to the 2nd router.
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
I have recently purchased a RVS4000 router and am experiencing major downtime.Almost everyday the RVS4000 router losing internet connectivity. I noticed that when this happens I cannot login into the router from my pc which is connected to the RVS4000 network.The only way to restore connectivity is to restart the RVS4000 by disconnecting power and powering back up.The router's WAN is connected to my Cable modem.The RVS400 has two PC connected to it. (port 3 & 4) I have a Cisco 8-port switch connect to the RVS4000 with 3 additional PCs/devices on it.
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
when my Linux VM is running!How's this for a mystery - last night I noticed that I could no longer access my gmail. Thought it might be down. This morning, I still couldn't access it. Thought I would try comcast, no joy either. Changed computers, no difference. Changed routers, no difference. Bought a new router and started plugging in network cables one at a time. My main machine first, everything works - http and https sites, a second computer, all good. The switch. Fine. Powerline. Still good. Then I plug in a Windows server running a Linux VM. Https sites on all the other machines stop working. Pause the Linux VM, restart router - https sites return to life. Went to Linux machine, re-enabled ipv6 (the only recent change on the Linux machine was to disable ipv6 since upon a reboot, Linux didn't have an ipv4 address). Restart Linux everything seems fine. A few hours go by, try to connect my wife's new laptop and at that moment wireless seems to stop. Restart router, wireless is back. But lo and behold, https is gone again. Unplug the machine that has the Linux VM, restart router, all is good.Ever see anything this weird?
how to create a password to access one pc to another pc .like i have 3 pc it is connecting throw switch .ip addresss is 192.168.1.1,192.168.1.2, 192.168.1.3 i want access from 192.168.1.1 to \192.168.1.2 like this here i want to create login password and how to remove password
I am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.