I have built two servers,a cacti server and a syslog server.They are both in vlan 30.Both servers can ping each other and can ping the gateway.Now the problem is the cacti server can ping hosts in vlan 100 but the syslog server cant.I am using a subnet mask of 255.255.255.248.
View 1 RepliesI installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies View Relatedi am facing the same problem now but am using windows 2003 server
View 1 Replies View RelatedI have a network with three vlans: vlan 10 (172.16.10.0), vlan 20 (172.16.20.0) and vlan 30 (172.16.30.0).I want to make sure that clients in vlan 10 can access to vlan 30, but not access to vlan 20.Vlan 20 can also access only vlan 30.i have configured a router on a stick and the acl's, but some how i can't ping from vlan 20 to vlan 30. [code]
View 1 Replies View RelatedI'm using Cisco 2960 Series SI, configuring VLAN is not so hard. but i'm having problem with this one. base on the picture above i'm attaching on Fa0/4 and expecting not to ping the default vlan 1. but my question is why i can ping the other vlan since i dont have use any routing?
View 1 Replies View RelatedI'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
The is VLAN id setting in some network/LAN interface .... how can I ping this lan/network interface in XP ..any freeware can do it ???
View 1 Replies View RelatedI have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
I am trying to config the following setup in the Cisco 1841. Able to ping the IPs of Vlan1(FE0/0/1), Vlan2 (FE0/0/1) and FE0/1 IPs from corresponding networks. But packets are not flowing to other side.
View 3 Replies View RelatedI have a Cisco 871 router and I have successfully added a second vlan and connected a switch configured with that VLAN. Anyways, my problem is the device in my new VLAN (vlan200) are able to ping/access devices on vlan1. I do not want this to happen. I read somewhere that the 871 routes between VLAN's by default.
View 3 Replies View Relatedi am stuck in a issue! unable to ping the SVI
i am design a small network for a office.
1 router 2811
1 switch 3750-e
Router is connected to the mpls cloud with ospf.
here re the config.
Router#
int fa0/0
ip 10.10.10.1 255.255.255.252
[Code]....
i connect my laptop and give ip 22.0.68.1 255.255.255.0 and default gateway 22.0.68.251but can not ping SVI VLAN 201 (22.0.68.251) ?
and from the SWITCH i can not ping the 20.20.20.2?
I have an ASA that houses 11 VLANs, and I am trying to add a 12th.One of the VLANs is for PCs that have internet only access.The new VLAN will be similar, but for multifunction printers only.VLAN 99 is for internet only and works fine, I can ping the gateway of 10.99.3.33 from any PC in that VLAN.I am creating VLAN 98, modeling it after VLAN 99, and I cannot get a PC in the vlan to ping the gateway of10.98.3.17.Both switch and ASA show the new VLAN 98 as UP, switchport is UP/UP.I have deleted and recreated VLAN 98 a few times, but I cannot get a PC VLAN 98 connectivity.Once it is working on the core switch, I will add it to the trunk to the IDS switches. VTP is not in use, everything is manual. [code]
View 4 Replies View RelatedI have created two vlans, vlan 1 data and vlan 200 voice. the issue is that when an on one vlan i cannot ping the default gateway of the othe vlan from my PC. An using sge 2010p switches.
below is my configuration
p route 0.0.0.0 0.0.0.0 192.168.0.1
ip dhcp relay address 192.168.0.100
ip dhcp relay enable
ip dhcp information option
interface vlan 1
ip dhcp relay enable(code )
I have a cisco 876 with, c870-adventerprisek9-mz.124-6.T9.bin. I have configured a VLAN with ID 230, an SVI with IP 192.168.230.1/24 and I have assigned switch port fa 2 to it…
interface Vlan230
ip address 192.168.230.1 255.255.255.0
VLAN ISL Id: 230
[Code]......
I'm having some trouble getting my head round the following but I think it's routing related?
I have a Cisco 3750 switch with the following configured:
interface Vlan1
ip address 192.168.0.223 255.255.254.0
no ip route-cache
[Code].....
The 3750 is connected to a firewall which handles the routing. From the 3750 I can only ping remote networks from the vlan1 interface not from vlan6,8 or 10 i.e ping 10.34.37.101 (remote network) source 192.168.0.223 (vlan1) works but ping 10.34.37.101 source 10.74.10.1 (vlan10) does not? I can ping 10.34.37.101 from computers on the various vlans but not from the 3750 it self.
I looked at setting a default gateway for the various vlan interfaces
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below.
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....
Why I cannot ping vlan when no port connect to switch.
View 3 Replies View RelatedThe server is on a different network and the desktop is on a another network.I can ping the server but i can't access any drive on the server.
View 1 Replies View RelatedAble to establish wireless connection to broadband router but cannot browse internet as it seems unable to resolve site names.Unable to ping DNS server from the pc, get request timed out message
View 9 Replies View RelatedRecently i changed internet service provider and i went up to a 24 Mbps line, though i can only reach a 8 Mbps service due to my location.
The problem is that surfing the internet has gone all kinds of wrong. Every page takes at least 20 secs to open and the response to online games has the same, or even more, delay. Checking my emails also takes quite some time.I tried connecting through the ethernet cable & the wireless connection(not at the same time). I even tried making a static ip. Same results, i can't seem to browse.
I insert data from two clients.(1 window server 2003,2 XP clients ) the two client print paper and the printer is shared printer. At the same time two clients print paper and the printer stop working. So I restart my two clients and server. After restart the clients cannot ping to server.
View 1 Replies View Relatedi have server 2003 sp2 with "AD " , every thing was working just fine until yesterday the server goes down i cannot ping the "server"or its ip from any PC and i cannot ping any thing from the server only it can ping itself "localhost ,server, 192.168.1.1, 127.0.0.1 " when the problem happens it checked the server and the ipconfig was chenged to :
192.168.1.1
255.255.255.0
192.168.1.254
127.0.0.1
8.8.8.8
the DNs server was changed ! now my server is clean and i reconfig my dns server but no dns is working in my network the AD server or the DSL router/
I've recently swapped out an old pix firewall for a new ASA5505 and have been trying to match the configs as best I can. However I still can't ping the new firewall from the server and it still won't let them serve out. The firewall exists on a separate VLAN (vlan30), but the previous pix never seemed to care about that. I'm wondering if that might be part of the problem.
View 8 Replies View RelatedA Windows Server 2008 r2 with 2 internet ports. One (IP: 10.0.96.132) connected to company intranet and one (192.168.10.1) as DHCP server connect to several PCs (192.168.10.**) through a switch.The problem is the PCs (192.168.10.**) can ping the DHCP server (192.168.10.1) , while DHCP server (192.168.10.1) can not ping (192.168.10.**).How to configure the server so that all these PCs can access the intranet?
View 4 Replies View RelatedAbout my internet setup, I receive internet from my ISP via the LAN cable. The IP is static, provided by the ISP. To use the internet, I have to login to their server using a username and password.Earlier, I did not have a router. So, to see if the ISP server was up, I could just ping the IP of the ISP server from my computer using the command prompt, and it would show whether it was up.However, since I got a router, I find that I cannot ping the ISP server from the computer directly as before. To ping the ISP server, I have to open the router administration page using the browser, then use its diagnostics feature to ping the ISP server. It shows only a few pings, and is not like the continuous ping that can be seen when you run ping from the command prompt. So, it's difficult to see the pings, and also diagnose. Also, sometimes the router pages do not open and get stuck, even after being refreshed.Is there any way, or any setting, by which I can ping the ISP server from the command prompt on the computer? Do I have to make changes in firewall settings of computer, or any settings in the router?Why can't I ping the ISP server directly from the computer?I am using Windows 8. The firewall of Windows 8 is on, and the hardware firewall on the router is off.
View 9 Replies View RelatedI have a windows 2003 server. It had been working and then a couple of days ago the computers on the network could no longer find the server. I cannot ping the server anymore. I have replaced and tested all cords and routers between the computers and the server
View 5 Replies View RelatedI have recently got our Cisco engineer to create a VPN connection to our network through a ASA5510. I am able to ping all devices on the network bar two servers (2xW2K3, one configured with AD/DNS and the other is a AD/file server) using IP addresses ,However, I cannot ping any devices using host names. The engineer has entered in the correct IP address of our DNS server, but still we have this issue. As the VPN client cannot ping the DNS server, it is unable to resolve the host names, but I cannot seem to work out why we cannot ping the DNS server.
View 1 Replies View RelatedNot sure what's going on with this thing. Unfortunately I'm 3 hours away from where it's installed. We put it in place about 3 months ago. It's set to use failover and load balancing. When I installed it I tested the failover and load balancing and everything worked as it should. The past 2 weeks the unit has not been failing over when one ISP drops. This requires a power cycle of unit to get the secondary on X2 to pick up. Data collection is turned off. Probing is turned on for both WAN ports. While both ISP's are up it load balances fine. I was there last week and pulled the patch cables going to the modems and it didn't skip a beat doing a constant ping. Just randomly it takes a shit when one ISP goes down. Takes out the network as well as no internal resources are reachable as well. Can't ping the server from any PC's and such.
It's running an older firmware. 5.5.6 from Nov 2011. 5.8 is currently available. I'm just leery about flashing a new firmware remotely.
Anything like this before with these units? We have plenty of 170's and 180's in place that are trouble free.
two of my workstation can not receive ip address from the server but can ping server. So i can not browse with them
View 3 Replies View RelatedI use a Buffalo Nas LinkStation WXL server to back up my files and data. It has been working perfectly and we have saved some files and data in it.However, we turned it on one day and it had disappeared from the list of Computers on the network and for a while now we haven't been able to get in. It is not showing in the list of Computers in Network and its webpage keeps coming back as "Unable to Connect" or "Taking to Long to Respond".The server is visible on the router's webpage under DHCP Clients List and we can ping the server and get a reply. But none of the laptops on the network can view it neither can I (the administrator) get access to it via its webpage?
View 1 Replies View Relatedi have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies View RelatedI've configured a lot vpn server for 857/1800, etc. But this has never happened.I configured 881 as VPN server using CP.Shared key, local group and local user authetication with split route.Local pool 192.168.100.1-254? I have acl for telnet which allows local pool IPs.I have acl to deny local network to local pool IPs for NAT.I've deleted the whole settings and re-run the wizard. It's still the same thing. I can connect from the VPN Client, but no traffic going through. The problem to me is isakmp with DPD. But why it is dead? Why no response from the server? If it is an error, why connection has no problem.
View 1 Replies View Relatedim trying to connect a dell MD3000i to a Cisco 3750-s but i am not abel to ping the server.the status is up and Protocol is up. but still nothing.i configerd the port to be a acces port and also at trunk port but still nothing is happening.
View 1 Replies View Related