All the pc's can't connect to my DNS server some a few minutes and then it gets back online, well windows says it can't connect to the primary DNS server.I have a router in between (a sitecom DC202-v5) and the router says it's gateway in unreachable. So what could be the problem for this? Because it's really annoying when playing online games.
View 18 RepliesI have install the administration toolpack on Windows 7 and enabled remote connections on my server 2008 box, When i try and connect with my Windows 7 server manager it does not work.I see stuff on google about enabling a trustedhost with winrm but can't find a way to do this.
View 18 Replies View RelatedAfter getting New Workstations, I wanted to connect that to the SERVER but Windows 7 could not log into domain of our server with Windows Server 2003. Besides following the proper process/steps. I am able to use the printer and internet shared through SERVER though.
View 2 Replies View RelatedI have a new computer with windows 7. Will be terminal for a server using xp.My computer detects the server but I do not succeed to access with username and password.
I have done the following:
Changed workgroup name to same as the rest of the terminals.Changed computer name to same as my previous computer in the network.Previous computer read only chosen username (+ password) when accessing.This new computer reads both computernamechosen username (+ password) when trying to access.
I suspect that username is not approved due to "double-name" ?
I am using a old notebook (2 years old) with windows server 2008 on it. I needed to remove al the drivers, because windows server 2008 isn't using the drivers of windows xp, and it wanted a clean installation.
Now the question and problem, is it possible to let my server wireless connect to my home network?
I am using for a server my old notebook:
Acer Aspire 5738ZG
2GB RAM, Intel Pentium dual-core processor T4200
Nvidia GeForce G105M 512MB (doesn't matter)
Atheros AR5B91 Wireless Network Adapter
I already installed the driver for the Wireless network adapter. Windows can't find any networks, when i try to connect.
My Windows xp computer can't connect to the DHCP server correctly and thus can't connect to the internet. It is connected through an Ethernet cable to a wireless router. All other computers on the same network connect fine to the router, both wired and wireless.This all started after I left my computer alone for a few hours and came back with it not coming out of idle. After shutting it off and turning it back on, it would not connect to the DHCP server.It assigned me the autoconfig address 169.254.189.73 because it couldn't connect to the DHCP server. I even tried a static IP but even that wouldn't fix it. I have tried the same ethernet cable in another computer and it worked fine so I know that it is because of my computer.I have tried renewing and releasing the connection using ipconfig in the command prompt but that did nothing. The settings are all the same as the other computers running through the same router. I have tried shutting down all the other computers and reconnecting the trouble one but again still nothing.The last thing I'm not sure about is the network adapter driver. I have reinstalled it but I'm not sure if the driver is correct. I have an NVIDEA nforce 10/100 Mbps Ethernet adapter. I attempted to reinstall but I'm not sure I selected the correct generation when I downloaded the driver installer. My computer says nothing about the generation of the adapter so I just chose the newest generation. My adapter is integrated in the motherboard.
View 19 Replies View RelatedHave nearly new desktop running Windows 7 and cannot connect to Internet (BT broadband in wireless mode). Error message says 'cannot connect to proxy server'.
View 4 Replies View RelatedI have windows vista and my modem is connected to a router it was working fine than all of a sudden I get a connection than I lose connection right after.
View 1 Replies View RelatedHow to connect window server data to website. when i change in server than update website data.
View 1 Replies View RelatedI am with Virginmedia networking. my main computer is attached to the hub but another one in the same room as the hub is picking up the Sitecom range extender at the top of the stairs, and 3 other computers are picking up off that but it is saying it is unsecured.how i can secure the Sitecom extender.
View 3 Replies View RelatedI planned for my customer to replace his old LMS 4.0.1 server under Windows 2003 by a new server under Windows 2008 R2.Customer wants also to set a new LMS name and IP address for the new server under Windows 2008 R2 and keep both servers on the network.I'm wondering what could be the best procedure to do that migration.Can I used backup / restore procedure in that case ?If yes, what file must I modify to adapt the new LMS configuration to new hostname and IP Address ?
View 2 Replies View RelatedI am trying to set up to watch a live webcast and get the the following essage,"Windows Media Player cannot connect to the server. The server name might not be correct, the server might not be available, or your proxy settings might not be correct." I have tried to verify proxy server settings and it still gives me the message.
View 1 Replies View RelatedI'm having trouble to connect the router to windows server 2003 ( I set up this latter as a router) I have also set up the loopback
View 4 Replies View RelatedI build a local DNS for namming my local network on windows server 2008 , but due to setup local DNS ,when I want to connect to internet from my pc , I can't do it . because my DNS set with a local IP such as 192.168.1.10. What can I do that have an Internal DNS and can use internet with that too.
View 1 Replies View RelatedIf I have two servers, one running Windows Server 2003, and one running Ubuntu 10, what would be the best way to 'map' one's drive to another? Either way is fine. They are each in a different state, and each have an external IP. I just need to do some processing on the Ubuntu server, then write the file either to its own drive, and have the web server (Windows) read it, or, have it write to the Windows HDD, and have Windows read it.
View 2 Replies View RelatedI am trying to set up this new extender on XP platform. I have only got as far as the username and login screen. I assume that this is asking for the nambe by which the PC (with me as user) is known and the password for this PC. I cannot get these recognised.
View 4 Replies View RelatedSince a few days I've installed my Sitecom 300N Repeater to extend the wifi signal at my home.I named my repeater the same as my wifi UPC modem (Cisco EPC3925), so the PC will see 1 connection instead of 2. I also turned off the DHCP server on the repeater (not sure what it does, but it was recommended when I was goggling around).fortunately I'm experiencing a lot of trouble. Although I can connect to the repeater, the signal is not always stable. Many times my connection speed is as low as 3 Mbps. When I quickly turn the power off and on it instantly jumps back to around 40 Mbps and stays like that for a few hours/days.It's very hard to debug this problem because after resetting the the repeater is doing very good until it slows down or even dispersers after a few hours.
View 4 Replies View Relatedmy router is sitecom gigabit 300N. since the past week there is this yellow exclamation mark on the connection in the task bar, near the clock. if I pass the mouse over it, it says no internet connection, eventhough I'm connected to the internet and I'm writing this right now, this is on desktop pc and connected to router by cable. the same thing on my laptop that is connected through WiFi, the signal strenght is normal, but there is the same exclamation mark. I'm pretty sure its the router not the PC because this happens on two different machines with the same router. I tried turning the router off and left it that way for about 7 minutes but that didnt work. is there something in settings I should do? or throw it away and buy Linksys/D-link router?
View 6 Replies View RelatedI have recently bought a new wireless card and it is giving me grief. Until now I had been using a laptop to pick up the wireless signal from my router, and pass it along to my PC, and have been receiving excellent speeds (30 Megabit) despite being 2 floors above the router.
I bought myself a Sitecom N300 card to go in the PCI slot of my computer, and my connection is generally extremely slow, and often drops completely for minutes at a time. The strange thing, however, is that it still shows medium to strong signal strength, even when the connection drops completely!
This is completely baffling me! I can't work out what could be causing interference, or why the signal strength doesn't go down when the signal does, or why the internal laptop wi-fi receiver seems so much better than this new card with 2 massive aerials. Unfortunately my ability to move either my PC or router is somewhat limited
I'm running Windows 7, fully up-to-date, and the router is a BT Home Hub 3
I have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View Relatedi've been using a VPN to connect to my home network from elsewhere for a few months. It's set up as follows:
PPTP
Maximum Strength Encryption
EAP-MSCHAP-v2 Authentication
Now I find out that MSCHAPv2 authentication has been broken and is no longer considered secure (even by Microsoft), so I want to change the protocol I'm using to make it secure.
However, I've spent 3 hours now researching this and I cannot for the life of me figure out how to use a better protocol on my Windows Server 2012 home server. I've tried setting up PEAP authentication (still PPTP) a la Microsoft's recommendation document, but it requires a certificate. I've created a self-signed certificate but it seems I can't issue certificates (via this method) without being a member of a domain, so I'm stuck. I can't even get started with L2TP since I can't find the option for it.
My question is this: Is there a way to setup a secure VPN server using Windows Server 2012 without a domain? If so, how do I do this?
i am facing the same problem now but am using windows 2003 server
View 1 Replies View RelatedIs there an iTunes Server for WHS 2011 available?
View 3 Replies View RelatedI've been reading that the Windows Server Backup that is included with Server 08 R2 is pretty good. Is spending $400 on a third party utility worth it?
I'm asking because we're purchasing a new server soon and I want to know if the included backup is going to be good enough. Will be backing up server state as well as data to tape and possibly an off site server (server 2003) if I get my way.
I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
I have a win xp laptop which connects via wireless to a cheap belkin router I have a Win 7 pro laptop which is hardwired to the router. The Win 7 machine is NOT set up for home groups. We are all on the same workgroup.
I have added the user name from the XP machine to the Win 7 pro machine with admin rights. I shared a folder on Win 7 and added the user name and gave read/write rights. I have no software firewall.
When I try to connect via win explorer via the workgroup I see the Win 7 machine (after 10 seconds). I see 'User' folder which I can browse and I see the folder that I shared but I can't access it. Access denied...
My friend and I bought Acer Aspire 5741's about 9 months ago and neither of us has had any problems until now. My friend went to connect to the internet via wireless router yesterday to find that there was limited connectivity (no internet access). We assumed it was a router issue and I gave her a number of things to check but all seemed ok with it. I went to her house to look at it today and when I ran the connection troubleshooter got "windows can't communicate with.......... (DNS server)". I connected my laptop via her router and everything was fine. I brought her laptop back to my house and tried to connect to the internet via my router and got exactly the same 'DNS' message - my laptop again connected without any problem.
I have re-booted the routers, laptops, network adapters etc and also checked the wireless adapter settings on both laptops, which appear to be the same. I have re-set the TCP/IP stack and have also tried ipconfig /release and /renew - none of which seems to have made any difference. The results of ipconfig/all are:-
Windows IP Configuration
Host Name . . . . . . . . . . . . : Debbie-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
I am running a small network of 30 pc. I have installed windows server 2003. Now i want to upgrade it to server 2008 but before that i want to test windows server 2008. That is why i,m looking online for a copy of windows server 2008 with reg key. Is there any good and trusted place to get windows server 2008.
View 1 Replies View RelatedI am working remotely & unable to access my company's 'ftp server'. The 'box' stated "NO SUCH INTERFACE SUPPORTED'. I have just bought a new Acer laptop & it'll be a complete waste if I can't use for work.
View 4 Replies View RelatedI have a dedicated windows server 2008 r2 enterprise.I am running an SSTP VPN but only have 2 IP address to connect to the internet on.My issue is that one of the IPs is for the IIS7 etc and the other is for VPN use.How can I apply the same IP to more than one user allowing them to connect all at one.There are in total about 5 users who want to use the VPN service and I dont really want to pay.How do I apply the same IP to all accounts and allow them to connect and all use the same IP at once.
View 5 Replies View RelatedI have a XP home SP3 as a server. My wired pc's all can see and connect to the server. I am now trying to add the wireless laptop running 7 Home. I can see my wired 7 Ultimate in the network window. I cannot see my server running XP.
View 1 Replies View RelatedI've setup the vpn on my Windows Server 2008 R2 box, I now need to do the firewall part - whats the easiest way of doing this as I can see there is a VPN Wizard on the PIX, or can I just open up the ports on the firewall?
View 6 Replies View Relatedi'm new, then i don't know what is my dns server names and ip
View 3 Replies View Related