Region : Ireland Model : TD-W8980 Hardware Version : V1 Firmware Version : 0.6.0 0.6 v000 build 130303 rel. 38108n ISP : Eircom
Bought this adsl router on Friday and since then I have been experiencing random frequent wireless dropouts, router appears to reboot at this point too, Internet drops out too. Wireless drops as I hear the beep from my airplay speaker reconnecting. Any one have these issues too, tired changing channels, then back to auto again, still no joy.
Region : UnitedKingdom Model : TD-W8961ND Hardware Version : Not Clear Firmware Version : V.3 ISP : ADSL24
Using windows 7 and 8 on different machines I am unable access my routers web based set up.
I enter the usual "admin" and password in the login box. 3 goes and then get error message. or hangs on waiting.(connected to the router with Ethernet Cable). Could this be a windows based problem. I think it was ok on XP but that is gone now. Router is working fine but I just cant access it to alter any settings.
My 2 other spare routers which are not TP-link also have the same problem.
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
Region : Others Model : TD-W8901G Hardware Version : V6 Firmware Version : ISP :
problem with filtering
Region : Syria Model : TD-W8901G ver 6.0 54Mbps wireless G ADSL2+:
I used the url filter utility inside the router program. I put some url for example www.google.com, I wanted to try the filtering cababilty, Later I deleted all these adresses , but unfortunatley it keeps telling me the following message: "The system returned: (110) Connection timed out The remote host or network may be down. Your cache administrator is webmaster@proxy1."
Region : UnitedKingdom Model : TD-W8951ND Hardware Version : V1 Firmware Version : Latest ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
Region : Others Model : TD-W8961ND Hardware Version : V3 Firmware Version : 3.0.0 ISP :
My router is TDW8961ND The firmware version is 3.0.0 The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
Region : NewZealand Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111130 Rel.56405n ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
My DIR-655 has worked well for 3 months; both Ethernet and wireless. Yesterday I accidentally deleted this WiFi router from my Kindle Fire list of WiFi connections. Now, when I try to re-establish Kindle wireless logon, the router will not accept the previously used password.As a non-techno-geek, I tried to find this in the DIR-655 manual. But it is written in Greek and not oriented to the wireless user. [code]
Logon failure: The user has not been granted the requested logon type at this computer" Im having this same problem on two computers. One running windows vista ultimate 64bit and windows 7 home premium 32 bit to windows server 2008 r2 64 bit?
I have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
I cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
I found out that I cant access my modem (TP-Link W8901G) config page at 192.168.1.1. I was pretty sure my ID and password is correct since I never changed them. It is also unlikely that the password got changed by other people who are stealing my Wi-Fi as I turned my WLAN on only when I requires the connection then it get turned off afterwards.
I upgraded my router from version 1.2 to 1.35NA, through the Tools / Systems page on the router (uploaded the bin file). I am connected to the router via a wired connection.
During the upgrade, the message said I wouldn't be able to access the webpage until 75 secs. I watched it count down the seconds and then when it refreshed, I could not get to my routers page: 192.168.1.2
The DLink Router is connected as a pass through router to my FIOS router, so that I can use the wired ports and I use the DLink as my wireless router (fios router wireless strength was poor).
All the lights on the router are working as though everything is ok. I am still connected to the Internet, so it appears that the pass through of my wired ports is still working after the firmware upgrade, but wireless is not. Not surprising. I expect I may have to upload my settings (which I did save), but since I cannot get to the routers page, I feel a bit stuck.
two more bits of into. I also tried getting to 192.168.0.1, which might be the default? and I cannot get there either. My Fios router is on 192.168.1.1 (and as mentioned, the DLink should be at 192.168.1.2). Fios Router reports that the 192.168.1.2 port is inactive.
I am using D-Link DIR-615, I need to ask is it possible that i change the error page "Forbidden Web Access" ? I have blocked some websites and i dont want ppl know that it is blocked by router because in D-Link default error msg it is clearly mentioned that " This page is not included in the router's Allowed Web Site List". Is it possible that i redirect error page to some other site? or change error message?
Whenever I enter 192.168.1.1 to access the login page of my router, I cant access it to configure it even after resetting it !I also tried changing TCP/IP settings to static as mentioned in the router's manual but it dint work?
I have been using this router for 6 months without problems. However, it hasn't been working since yesterday morning. It receives power but the Internet led doesn't light up. The network leds are blinking faintly and rapidly. I can't access the configuration page from my browser. Is it dead or not?
Region : Portugal Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : UnitedKingdom Model : TD-W8968 Hardware Version : V1 Firmware Version : latest ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
I have three PCs in my lan. (A, B & C).I can access shared drives of B & C from A
I can access shared drive of A from C but cannot access B from C
I can access shared drive of C from A & B.
I get error message "Logon failure: the user has not been granted the requested logon type at this computer".
All the systems are Win 7, A & B are desktop and C is a laptop.I added the C's name in A's "Security Settings -> Local Policies -> User Rights Assignment -> Access this Computer from the Network" too. Still can't access.
Region : Australia Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
Im having issues setting up port forwarding with my Synology NAS.
My house is all connected via network cable, going to a main 24-port switch, which is connected to a Modem/Router (TP-LINK in this case). I can access the NAS from anywhere on my home network, send and receive is fine. I previously used a Billion modem/router in the same config and it all worked fine.
The problem is that when going through the Synology setup, it fails to see the tp-link. So therefore I cannot run its port forwarding program to setup all my ports. Which in turn the NAS can't access the internet. I have started going through the port-forward setting on the router interface, and manually entered the ports - i realized that I'm limited to the number of ports i'm allowed to open! I have also run a port testing program, some are successfully opened the others are not.
Is there some button i need to check or switch on the modem?
Region : Italy Model : TD-W8970 Hardware Version : V1 Firmware Version : TD-W8970_V1_130201
I just bought online a brand new TD-W8970 modem/router but I'm in trouble with getting ADSL working.I set up a PPPoE connection with the settings from my ISP but the ADSL Led on the device is solid OFF and in the Admin section it says DSL Status: Not Connected.
Region : UnitedKingdom Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP : Virgin
I've just replaced my aging ZyXel Wireless Router with a TD-W8970 which connects to the internet with no problems whatsoever. However, I have an ethernet connected Western Digital MyBookLive NAS which is happily allocated an IP addess but does not show up on my network on my PC (Windows Vista - fully patched). A usb connected pen drive and exactly the same. Am I missing something blindingly obvious? On the ZyXel the NAS worked with no problems whatsoever.
The problem with the NAS was my internet security Bitdefender. For some reason, on installing the TP-W8970, it switched my firewall status to public from home/office. Corrected that and the NAS can now be seen over the network. This does not fix the USB attached pen drive not being seen problem though.