WRT320N Speed Completely Unacceptable
Mar 20, 2011
Roadrunner plugged directly into my computer:
Ping: 29ms
Download Speed: 22.16 mbps
Upload Speed: .85 mbps
Roadrunner through my WRT320N, whether wireless or plugged into my computer(s)
Ping: 850-1400ms
Download Speed: .09 mbps - .25 mbps
Upload speed: .04-.06 mbps
Occasionally I get passable speeds in the 6 mbps range for download speed, but lately the router has performed this way nearly all the time.I've tried reflashing the firmware. I've tried multiple combinations of suggestions, ranging from adjusting single frequencies to adjusting MTU size, etc. Nothing works. This router simply CANNOT be this bad.
View 4 Replies
ADVERTISEMENT
Apr 23, 2013
I have purchased Linksys WRT320N because my ISP give me speeds of 400 mb/s download and 200 mb/s upload. After I tested the speed my router get only 137 mb/s, why is that? I paid for gigabit router!?
View 7 Replies
View Related
Mar 25, 2013
My custom built computer, only 4 months old, is right now getting an approximate internet connection of 4 mbps. I'm supposed to be getting 60. (This is mbps down by the way) how to get my speed back? I've tried other network adapters but it's not working.
View 8 Replies
View Related
Jun 29, 2011
I'm trying to set up a site-to-site vpn between a cisco 871 router(IOS 12.4) and asa 5550 8.4
The router conf:
crypto isakmp policy 1
authentication pre-share
[Code].....
View 7 Replies
View Related
Mar 11, 2011
Is there any way to add a printer to my computer that is on a completely different network? It's a small residential setup on both ends.
View 2 Replies
View Related
Sep 13, 2011
For quite some time now my parents' wireless internet cannot seem to keep a wireless signal anywhere in the house unless you are sitting next to the router. I've been doing everything I know to try and keep the signal strong enough to use it down the hall in the living room.
I've tried using different frequencies and channels however this only seems to work for an hour then the network will fall off the network list entirely and then a few minutes later will pop back in. What is causing this signal to die out completely every few minutes? They've tried countless numbers of wireless routers in hopes it would fix the problem however this never seems to work. Is this an issue with the ISP and/or the modem they provide us? Wired connections work fine, just wireless connections refuse to either stay up or constantly disconnect the user from the network.
View 5 Replies
View Related
Sep 11, 2011
I currently own a Sony Vaio Laptop that has been working fine for the last 2 years, I was happily on facebook when all of a sudden, my laptop started lagging massively and it disconnected me from wifi, I was shocked to find that when I tried reconnecting, the laptop decided to stop working for a second and my wifi stopped working completely, every time I disconnect the Ethernet cable from my laptop even though my wireless switch is on, it won't even pick up my Virgin Media superhub I have about 5 meters from my laptop, it indicates that there is NO wifi anywhere, just the ascending bars with a big red X on it
View 1 Replies
View Related
Mar 17, 2012
I am getting wireless signal in every room except one of the bedrooms.I have upgraded to a better router Buffalo N450 AND added a wireless USB on to laptop.Here is the weird thing.I have 100% signal strength all the way to the bedroom door. One step inside signal drops to 20%, further inside it can get to Zero BUT if I just take ONE step into the bathroom which is in the bedroom.. signal goes back up to 100%... one step either way goes from 100 to Zero... What the heck?I live in an Apartment building.. What could possibly be upstairs or in the roof thats only blocking signals in this one room!
View 1 Replies
View Related
May 13, 2011
I had a network connection to the main family computer that just completely disappeared after I got back on it. It had been on all day because it was defragmenting, but a few minutes after I got back on it (I had just sat down in the chair and sent a couple messages on a chat I was in and dismissed an "Oh, Windows Media player found another WMP on main computer! Wooo!" notification) and then it was gone.
I assumed the internet had crashed so I gave it a couple hours, no internet. I stayed up longer waiting, writing, playing some games, but nothing. I didn't check the Network computers thing until now.
Usually even when the internet crashes the main computer still shows up in the computer list but it was just mine then. It seems like it totally dropped the connection and it can't find it again when I try to create a new one. It's not like I watch p~rn or download anything I'm not supposed to download so...
And the network icon doesn't have a big red no connection at all x - It's just the two computers, no world icon, no x. I've tried booting in safe mode with networking, nothing, 'netsh winsock reset catalog' + 'netsh int ip reset.log, nothing, create new connection, nothing, and repair memory problems, nothing. : Microsoft Security Essentials found no viruses after a full scan, and it had been updated hours before the internet had a tantrum. I recently uninstalled Malwarebytes because according to a friend its update crashed her computer so I have no other virus scanner to use.
Oh, I'm runnning a Windows Vista Home Premium. Mine is genuine, it came with the computer, but my father had the bright idea to use -my- Vista disc to install it on the main PC, so it's all 'rawr not genuine' though as far as I know, my father's W7 laptop is still running just dandy.
We use a D'Link router, and it's worked fine until now. I don't actually know how my computer is connected, I'm pretty sure it's hardwired to the modem or router, but my father's is wireless. I've been searching like mad for the router's wireless USB thing, but it seems to have walked out the door.
View 8 Replies
View Related
Mar 7, 2013
My Network is gone from my list of available networks on my MacBook. I use s NETGEAR router, my network name is simply "NETGEAR" i have never named it anything else since installing this over 4 years ago. I have unplugged the power cord, waiting several minutes before plugging it back in. Also tried unplugging both the cable and the power cord. The router has no small "pin hole" that i can see in order for me to try to re-set it this way. It has literally disappeared from my Mac. Do i need to re-install using my NETGEAR cd?
View 2 Replies
View Related
Mar 12, 2012
-No hardware profiles on "change adapter setting."-Network Adapter isn't shown in Device Manager.-Reinstalled windows 7 and problem still persist.
View 4 Replies
View Related
Aug 8, 2011
I'm on a home computer and we use a router to deliver internet connection to the multiple computers in our house.However, lately I have been noticing that occasionally one of the computer's, on the network, internet connection drops but yet all the other computers are still working fine with their internet connection. And the internet doesn't completely turn off, like there is no "X" on the two computer screens down below...it just loses its little globe icon...In order to get back the internet, you would have to basically disconnect from the internet connection network and then go back into it and it's back again.
I was wondering, because I'm starting to get suspicious, is it possible that somebody on the network in my house the deliberately found a way to turn of the internet access for one of the computers? I was alerted by checking different websites that it is possible that somebody on your own home network can "hack" into another computer, view its internet history, and even disable internet. How do I know this is happening for sure and take steps to stop it. I want to catch who is doing this because nobody is telling the truth .
View 5 Replies
View Related
Nov 5, 2011
I was surfing the web one night and noticed that it was getting late so I turned my computer off.... I get back on in the morning after to find that my internet has completely stopped working. I tried everything like restarting, system restore[CODE]
View 1 Replies
View Related
Jan 24, 2012
II tried to make a wep password. and when i made one, i went on my laptop to try to find my network but my network name was completely gone from the list of available wifi networks i can connect to.
View 2 Replies
View Related
Jul 21, 2011
I bought the DIR-655 less than a year ago in Amazon, shipping it to NY. And then I came back to Uruguay. Almost 3 months ago the router stopped working completely and I started to search for support in Uruguay.After calling US support I was told I should contact the local or regional D-Link (which I later found is D-Link LA). And via DLinkLA.com I found the company TELEDATA S.A. url... who does the official support for D-Link in Uruguay. They told me the router couldn't be fixed, and told me DLinkLA, which is based in Chile, would either send me a working one (they also told me the service/warrany was already approved), or send me the money and gave me their contact details.After two weeks of contacting them, trying to get their attention, they finally told me it was not their responsibility because it was bought in the US. And now they don't return my e-mails.
View 5 Replies
View Related
May 14, 2011
Is there any way to disable internet access for selected PCs, while still allowing them to access the LAN?
View 2 Replies
View Related
Sep 1, 2012
I have a DIR-615 router. I would like to know if it is possible to block a PS3 from accessing the internet completely, without blocking any other computers/devices. I have access to the router, but not to the PS3 itself.
View 3 Replies
View Related
Mar 4, 2011
I have a switch connected from the internet outtake in my apartment.This switch gives internet to two, or sometimes three computers, by cable.To get wireless I have a DLINK-615 connected after the switch.This solution works flawless for some time, just after the router is started or reset. If I go to speedtest.net both the upload and the download works flawless.However, after around half an hour it's virtually impossible to upload, which gives heavy lag in programs like skype and games. If you try to speedtest.net now the download is still fine, but the upload gives a result of 0.1mb/sec after trying to even start the test for 3-4 minutes.Router giving up upload completely
I've tried to change the IP in the router to prevent a conflict between it and the switch. The problem is still there whatever IP I choose though, I simply have no upload.I've also tried to disable the DHCP, mess with the MTU and to enable the Access Point mode with no result.
View 2 Replies
View Related
Jan 25, 2013
I have 3750x with existing small business server and all computers on one vlan. This vlan connects to other switches with fibre trunk sfp's.I want build a new forest utilising vlans in the normal way, what is the easiest way to segregate this vlan?The site is running 24/7.
View 6 Replies
View Related
Jan 17, 2013
We are running ACS 4.1 on Windows 2003 server. The disk filled completely up with years of log files. We have freed up space but now none of the services will start back up either automatically or manually.
View 4 Replies
View Related
Jun 13, 2012
After an upgrade from LMS 4.2 to 4.2.1 Legacy menu is completely empty. Is it a bug? If it's empty, how to get to some of DFM options (like rediscovery, discovery status etc.) They seem not present in "Site map".
View 4 Replies
View Related
Jan 19, 2012
Whenever I access a file through HTTP, it seems to require that I completely load the file before it will display.
1) For large images, this will result in the whole thing taking some time to load before displaying in its entirety, unlike the usual progressive rendering.
2) For file downloads, this will result in the file being downloaded only after being cached, appearing only when the whole file has finished downloading, unlike the usual process where it can be seen as a progress bar in the browser's download window (for some reason, FTP downloading seems to work normally)
3) For internet streaming video, this means the video will not display until the whole video has been buffered (i.e. will not play until fully loaded)
1) I am on a home network. Other computers (including my old one) do not exhibit similar problems
2) Using Firefox 9.01
3) Win 7 SP1
4) Realtek PCIe GBE controller
View 12 Replies
View Related
Dec 21, 2012
How do I remove the start up password completely from my Lenovo laptop
View 1 Replies
View Related
Nov 24, 2011
where to change version of windows I can not find where to change the version of my windows to make it compatible with my router..I know that there is a place to change it,but I can not find it...I have Windows XP and it is compatible with my wireless router.
View 3 Replies
View Related
Apr 6, 2011
I'm going to buy a WAG320N router modem.I've read the manual but I haven't found an answer to the silly question: is it possible to completely disable wifi, and surf in internet using the 4 lan port only?
View 2 Replies
View Related
Nov 17, 2012
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
View 7 Replies
View Related
Aug 15, 2012
I'm an architect working in a small office that happens to be home to two seperate businesses, each with their owner network. However, these two networks want to use the same large format printer. I recently purchased the RV180W since the Cisco representative told me i would be able to connect both networks to the router so they can both see the printer without seeing the files on each of the other networks. We simply want to share the same printer.
Network 1:
192.168.4.1
Network 2
192.168.2.1
Large Format Printer
192.168.4.151
Network 1 has the RV180W as it's router with three gigabit switches. Computers and peripherals are connected to the three switches. 1 port open on the last switch.
I want to configure the RV180W to see both 192.168.4.1 and 192.168.2.1
What settings need to be modifed in order to accomplish this? Do I need more equipment? Is it easier to put a wireless card in one of the computers on the 192.168.2.1 network and then set it to see the 192.168.4.1 network?
View 3 Replies
View Related
Dec 13, 2011
how can I completely disable DHCP on SR520-FE?
View 8 Replies
View Related
Feb 9, 2011
I am using bsnl broadband connection
modem: wa3002g1
os: xp(86x) / vista(64x)
A few days back I have changed the modem (don't know the previous model no) because of some issues. Since then I am not able to open most of the websites in Firefox, IE6/8, chrome, opera. If i connect with other network like reliance data card, those websites are opening, if i connect bsnl the problem will be same again. I called to customer care many times, but no use.
View 2 Replies
View Related
Feb 22, 2012
I am trying to set up WRT on my WRT320N access point so I can connect it to my other access point that also doubles as my DSL router.Where can I find the WDS on the WRT320N?
View 1 Replies
View Related
Jul 4, 2011
I've had this WRT300N for several years and it has worked very well.It suddenly dropped all wireless connections and no one can re-connect. My main pc is hard wired directly to the router and works perfectly as always. 3 wireless pc's and 3 handheld devices suddenly can't connect. I've powered down my modem and router for several minutes, but nothing changed. The firmware was upgraded a long time ago and there are no other upgrades available.
View 7 Replies
View Related
Sep 14, 2011
I purchased an E4200 from a retail store about ten days ago.It completely quits periodically. Even the managment interface is gone. It seems to just die. The only fix is to unplug it, count to ten and plug it back in.router also gets extremely hot. I have tried locating it in several places, no matter where I put it, it still gets very hot. Right now I have it straddling a trash can so that it has about two feet of air space under it. It is still uncomfortable to the touch.
When I contacted technical support all they would do is walk me through setting it up from scratch again. I've done that many times, and I do not want to do it agian. Setting the router up agian will not make it cool down.
1. Exchange this for another one, probably from the same batch, at the store?
2. Fight with Linksys tech support to get a waranty return? (Any input on how to get them to do this?)
3. Return this router altogether (paying the retailer's 15% restocking fee) and look for another brand?
View 8 Replies
View Related
Sep 29, 2011
I had an antenna break on a WMP54g v 4.1 and I was able to replace it with a WMP54g v 4 but I'm not having a lot of luck getting the driver to install. This is on Win7 32 bit Home Premium. I assume this is due to the fact that I was using a newer and switched to an older piece of hardware and there is some driver issues. How to uninstall the old driver completely so I can start fresh I have tried everything I know to do and can't seem to get anywhere.
View 1 Replies
View Related
