We are running ACS 4.1 on Windows 2003 server. The disk filled completely up with years of log files. We have freed up space but now none of the services will start back up either automatically or manually.
View 4 RepliesBecause the /var is 99% full, I have problems with taking backup. I have also problems with login into the web-page. I’m authenticated, but then I get: User Role is empty.
View 5 Replies View RelatedMy customer is tight on SN space, so they set up 400GB for the ACS AM. I saw a message about having less than 500GB flash by during the DVD install, but it seemed OK otherwise. When the VM boots off the HD, I get the localhost login prompt, and I type in setup, but nothing happens for about a minute, then I get the message 'INIT: ID "S0" respawning too fast: disabled for 5 minutes". After that, nothing. I've booted multiple times. Is this related to the disk space, and is it possible to install with less than 500GB?
View 7 Replies View RelatedI was asked to performe upgrade from acs 5.3 to 5.4 (vm), but i noticed that someone installed it on 80gb partition and there is 500gb as one of the requriments in upgrade and install procedure. What is strange to me is that "dir disk:" command shows such an output: 5165345067 bytes available.And under ESX i see 80gb partition. Anyway, is there any way to extend partition size to 500gb? Can I just change it under ESX? Is there any procedure to take under ACS console?
View 1 Replies View RelatedWe are getting ready to bring up 2 new 5.1 ACS servers to replace our ACS 4.2 configuration.The documentation says that 512GB of disk space is required for each server. This means we will need to request1 TB of disk space. The VMware folks in our group are asking why we need so much space when the 4.2 servers are only using 20 gigs including the OS.
View 3 Replies View RelatedThis is the error message I am getting on our ACS 5.1 appliance - is there anyway to purge the database or compact the file?
View 1 Replies View RelatedI have ACS 5.3.0.40 Primary Secondary Authenticators , of which the Scheduled backup has stopped.When checked the : Monitoring Configuration > System Operations > Data Management > Removal and Backup > Incremental Backup , it had changed to OFF mode. without any reason.Later i did the acs stop/start "view-jobmanager" and initiated the On-demand Full Backup , but no luck, same error reported this time too.
View 2 Replies View RelatedI am having trouble viewing all the Administration logs in ACS View. I have my Local Log Target set to a Maximum log retention period of 90 days. In ACS View I can display authentications that go back 90 days + However when I try and display the "ACS_Configuration_Audit" in View and perform a Custom query that goes back 90 days it will only display about 35 days of Admin logs.I know the logs are there because when I go into CLI and do a search like "show logging | i "ObjectType=Administrator Account" the Administration logs go back over a year.why ACS View cannot display all the Admin logs?The ACS is running v5.1.0.44 Patch 6 (Also experiencing this in a v5.2 ACS as well)
View 2 Replies View RelatedI have 3750x with existing small business server and all computers on one vlan. This vlan connects to other switches with fibre trunk sfp's.I want build a new forest utilising vlans in the normal way, what is the easiest way to segregate this vlan?The site is running 24/7.
View 6 Replies View RelatedAfter an upgrade from LMS 4.2 to 4.2.1 Legacy menu is completely empty. Is it a bug? If it's empty, how to get to some of DFM options (like rediscovery, discovery status etc.) They seem not present in "Site map".
View 4 Replies View RelatedIs there any way to add a printer to my computer that is on a completely different network? It's a small residential setup on both ends.
View 2 Replies View RelatedFor quite some time now my parents' wireless internet cannot seem to keep a wireless signal anywhere in the house unless you are sitting next to the router. I've been doing everything I know to try and keep the signal strong enough to use it down the hall in the living room.
I've tried using different frequencies and channels however this only seems to work for an hour then the network will fall off the network list entirely and then a few minutes later will pop back in. What is causing this signal to die out completely every few minutes? They've tried countless numbers of wireless routers in hopes it would fix the problem however this never seems to work. Is this an issue with the ISP and/or the modem they provide us? Wired connections work fine, just wireless connections refuse to either stay up or constantly disconnect the user from the network.
I currently own a Sony Vaio Laptop that has been working fine for the last 2 years, I was happily on facebook when all of a sudden, my laptop started lagging massively and it disconnected me from wifi, I was shocked to find that when I tried reconnecting, the laptop decided to stop working for a second and my wifi stopped working completely, every time I disconnect the Ethernet cable from my laptop even though my wireless switch is on, it won't even pick up my Virgin Media superhub I have about 5 meters from my laptop, it indicates that there is NO wifi anywhere, just the ascending bars with a big red X on it
View 1 Replies View RelatedI am getting wireless signal in every room except one of the bedrooms.I have upgraded to a better router Buffalo N450 AND added a wireless USB on to laptop.Here is the weird thing.I have 100% signal strength all the way to the bedroom door. One step inside signal drops to 20%, further inside it can get to Zero BUT if I just take ONE step into the bathroom which is in the bedroom.. signal goes back up to 100%... one step either way goes from 100 to Zero... What the heck?I live in an Apartment building.. What could possibly be upstairs or in the roof thats only blocking signals in this one room!
View 1 Replies View RelatedI had a network connection to the main family computer that just completely disappeared after I got back on it. It had been on all day because it was defragmenting, but a few minutes after I got back on it (I had just sat down in the chair and sent a couple messages on a chat I was in and dismissed an "Oh, Windows Media player found another WMP on main computer! Wooo!" notification) and then it was gone.
I assumed the internet had crashed so I gave it a couple hours, no internet. I stayed up longer waiting, writing, playing some games, but nothing. I didn't check the Network computers thing until now.
Usually even when the internet crashes the main computer still shows up in the computer list but it was just mine then. It seems like it totally dropped the connection and it can't find it again when I try to create a new one. It's not like I watch p~rn or download anything I'm not supposed to download so...
And the network icon doesn't have a big red no connection at all x - It's just the two computers, no world icon, no x. I've tried booting in safe mode with networking, nothing, 'netsh winsock reset catalog' + 'netsh int ip reset.log, nothing, create new connection, nothing, and repair memory problems, nothing. : Microsoft Security Essentials found no viruses after a full scan, and it had been updated hours before the internet had a tantrum. I recently uninstalled Malwarebytes because according to a friend its update crashed her computer so I have no other virus scanner to use.
Oh, I'm runnning a Windows Vista Home Premium. Mine is genuine, it came with the computer, but my father had the bright idea to use -my- Vista disc to install it on the main PC, so it's all 'rawr not genuine' though as far as I know, my father's W7 laptop is still running just dandy.
We use a D'Link router, and it's worked fine until now. I don't actually know how my computer is connected, I'm pretty sure it's hardwired to the modem or router, but my father's is wireless. I've been searching like mad for the router's wireless USB thing, but it seems to have walked out the door.
My Network is gone from my list of available networks on my MacBook. I use s NETGEAR router, my network name is simply "NETGEAR" i have never named it anything else since installing this over 4 years ago. I have unplugged the power cord, waiting several minutes before plugging it back in. Also tried unplugging both the cable and the power cord. The router has no small "pin hole" that i can see in order for me to try to re-set it this way. It has literally disappeared from my Mac. Do i need to re-install using my NETGEAR cd?
View 2 Replies View Related-No hardware profiles on "change adapter setting."-Network Adapter isn't shown in Device Manager.-Reinstalled windows 7 and problem still persist.
View 4 Replies View RelatedRoadrunner plugged directly into my computer:
Ping: 29ms
Download Speed: 22.16 mbps
Upload Speed: .85 mbps
Roadrunner through my WRT320N, whether wireless or plugged into my computer(s)
Ping: 850-1400ms
Download Speed: .09 mbps - .25 mbps
Upload speed: .04-.06 mbps
Occasionally I get passable speeds in the 6 mbps range for download speed, but lately the router has performed this way nearly all the time.I've tried reflashing the firmware. I've tried multiple combinations of suggestions, ranging from adjusting single frequencies to adjusting MTU size, etc. Nothing works. This router simply CANNOT be this bad.
Yesterday a coleagu accdently removed the CF card from the router now the router does no longer want to boot completely. It extracts the image from the CF card but when it has to initialize the configuration it stucks there for hours. Can it be that the startup config is somehow corrupted?
When i try to tftpdnld is says that the mac address is illegal.
The first line of the cookie looks like 04 ff 08 86 ff ff ff ff ff ff ff ff ff ff ff ff
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)Technical Support: [URL], Inc.PLD version 0x10GIO ASIC version 0x127c2801 platform with 196608 Kbytes of main
[Code]......
I'm an architect working in a small office that happens to be home to two seperate businesses, each with their owner network. However, these two networks want to use the same large format printer. I recently purchased the RV180W since the Cisco representative told me i would be able to connect both networks to the router so they can both see the printer without seeing the files on each of the other networks. We simply want to share the same printer.
Network 1:
192.168.4.1
Network 2
192.168.2.1
Large Format Printer
192.168.4.151
Network 1 has the RV180W as it's router with three gigabit switches. Computers and peripherals are connected to the three switches. 1 port open on the last switch.
I want to configure the RV180W to see both 192.168.4.1 and 192.168.2.1
What settings need to be modifed in order to accomplish this? Do I need more equipment? Is it easier to put a wireless card in one of the computers on the 192.168.2.1 network and then set it to see the 192.168.4.1 network?
how can I completely disable DHCP on SR520-FE?
View 8 Replies View RelatedI'm on a home computer and we use a router to deliver internet connection to the multiple computers in our house.However, lately I have been noticing that occasionally one of the computer's, on the network, internet connection drops but yet all the other computers are still working fine with their internet connection. And the internet doesn't completely turn off, like there is no "X" on the two computer screens down below...it just loses its little globe icon...In order to get back the internet, you would have to basically disconnect from the internet connection network and then go back into it and it's back again.
I was wondering, because I'm starting to get suspicious, is it possible that somebody on the network in my house the deliberately found a way to turn of the internet access for one of the computers? I was alerted by checking different websites that it is possible that somebody on your own home network can "hack" into another computer, view its internet history, and even disable internet. How do I know this is happening for sure and take steps to stop it. I want to catch who is doing this because nobody is telling the truth .
I was surfing the web one night and noticed that it was getting late so I turned my computer off.... I get back on in the morning after to find that my internet has completely stopped working. I tried everything like restarting, system restore[CODE]
View 1 Replies View RelatedII tried to make a wep password. and when i made one, i went on my laptop to try to find my network but my network name was completely gone from the list of available wifi networks i can connect to.
View 2 Replies View RelatedI bought the DIR-655 less than a year ago in Amazon, shipping it to NY. And then I came back to Uruguay. Almost 3 months ago the router stopped working completely and I started to search for support in Uruguay.After calling US support I was told I should contact the local or regional D-Link (which I later found is D-Link LA). And via DLinkLA.com I found the company TELEDATA S.A. url... who does the official support for D-Link in Uruguay. They told me the router couldn't be fixed, and told me DLinkLA, which is based in Chile, would either send me a working one (they also told me the service/warrany was already approved), or send me the money and gave me their contact details.After two weeks of contacting them, trying to get their attention, they finally told me it was not their responsibility because it was bought in the US. And now they don't return my e-mails.
View 5 Replies View RelatedIs there any way to disable internet access for selected PCs, while still allowing them to access the LAN?
View 2 Replies View RelatedI have a DIR-615 router. I would like to know if it is possible to block a PS3 from accessing the internet completely, without blocking any other computers/devices. I have access to the router, but not to the PS3 itself.
View 3 Replies View RelatedI have a switch connected from the internet outtake in my apartment.This switch gives internet to two, or sometimes three computers, by cable.To get wireless I have a DLINK-615 connected after the switch.This solution works flawless for some time, just after the router is started or reset. If I go to speedtest.net both the upload and the download works flawless.However, after around half an hour it's virtually impossible to upload, which gives heavy lag in programs like skype and games. If you try to speedtest.net now the download is still fine, but the upload gives a result of 0.1mb/sec after trying to even start the test for 3-4 minutes.Router giving up upload completely
I've tried to change the IP in the router to prevent a conflict between it and the switch. The problem is still there whatever IP I choose though, I simply have no upload.I've also tried to disable the DHCP, mess with the MTU and to enable the Access Point mode with no result.
I recently got my Cisco wireless system working a few days ago and am back with a guest network. Our wireless system includes one 2504 controller and 2 2602i access points. So, I want a wireless guest network completely isolated from the LAN.
Here is what I have done.
I have created a new internal network and assigned 192.168.2.1 to an unused port on the firewall and 2.2 to a new controller interface with vlan 10. I can ping both 2.1 and 2.2 from the firewall and the controller. Basic network connectivity is working. The DHCP server is setup on this same firewall and configured only for this port. This address is referenced in the controllers interface.
A new w lan was setup and enabled. The proper interface group was selected on the w lan. I have left the default layer2 security.
As far as AAA servers tab in this wlan, this is where I am a little confused. I wish to just have a single log in for this guest network. I wasn't sure what to do so I went over to the Security tab and created a "local net users" account. I do not know how to reference the use of this under wlan, security, aaa servers. Should I check the box that says "local eap authentication"?? If so, I don't have a profile name in the drop down. What I'm looking for is the username/password to be stored locally on the controller itself since there will be only 1 account.
Under wlan, advanced tab, I do not have "Allow AAA override" checked. Should I?
Lastly, when I try to connect the client, it is not pulling a dhcp address. I wasn't sure if authentication was required before dhcp or the other way around so I'm not sure what to trouble shoot first, authentication or dhcp.
I am using the RV220W with the latest firmware, I disabled all the four APs and also disabled the Radio, but the "Wireless" green light on the front panel still ON, why? How can I completely turn off the wireless?
Quoted from manual: WIRELESS—The Wireless light is green when the wireless module is enabled. The light is off when the wireless module is disabled.
Moreover I tried to disable the "Radio" while enabled one AP, I found that I can still connect to that AP, so what is the Radio's Enable/Disable used for?
I want to disable the telnet option/feature on ASA 5510
i tried no telnet alone it wont work as i didnt configured any telnet at all.
[URL]...
1655#comment-12826 I'm experiencing this bug and believe it may be causing a high cpu utilization. Does this bug mean the replay check feature is completely not functioning because I'd like to disable it.
IOS of 2 devices experiencing this issue:
ADVSECURITYK9-M Version 12.4(24)T
ADVSECURITYK9-M Version 12.4(22)YB
I have a RVS4000 and a WRT54GL router at home... I am planning to power down my home completely for several hours, my question is will I have to re-setup everything or will it retain the settings within the router?
View 6 Replies View Related