I have a denon avr2113 receiver wired to my router on my home network. It has internet access and shows up on the router, but it doesn't show up on my windows 7 computers, which are wirelessly connected to the same network. Any ides? Streaming is allowed on windows
View 1 Replies
I recently acquired a Latitude E6510 with Windows 7 Pro 64bit. My Dell DR984 Bluetooth KB/MS receiver works on my Latitude E6400 with win 7 32bit works but fails on the new notebook.
I have tried the Broad-com updater, but it fails with a message that Dell must be contacted. Where can I find drivers so that I can use the DR984 with my new notebook?
I have been trying to stream videos from my PC to my Xbox 360 via the Windows Media Center app. I've got it all set up, my PC detects the 360 just fine and vice-versa. However, when I go into the app on the 360 and select the video to play, it plays it extremely pixelated. Usually it just freezes up on an extremely pixelated frame while the sound of the video continues on as normal. I've tried MP4, MKV, AVI, WMV, etc. all at multiple resolutions all with the same result.I can stream just fine via HBO, Netflix, Amazon, etc. so I don't think it is my network or internet speed. I've tried putting the 360 on a static IP, I've gone through all the FAQ from Microsoft about enabling Windows Services and the like, none of which has made a difference.I am able to stream to my PS3 just fine, so I am not sure what is going on with the 360.
View 3 Replies View RelatedI have Comcast broadband with one modem connected to my PC. I just bought a Denon AVR-991 Receiver that has internet capability. I I plan to use it for internet radio, etc.The problem is that each piece of equipment is in different areas of the house. I could connect the cable modem to the receiver and connect the PC to the internet via a wireless router, but I don't want to lose the speed of a direct connection on the PC.. can I have two different modems connected to the same incoming cable line? FYI, the existing modem is a Linksys BEFCMU10, and the second modem is one Comcast is in the process of sending to me as I just added Voip phone service to my account.
View 2 Replies View RelatedI have a Cisco Wlc 4402 , denon 3312 & AP 1142 all three devices are same subnet . But Airpaly not showing in Iphone. But if i put a Airport express in on these subnet then i find airplay option. How without Airport express i can enable airplay...
View 2 Replies View RelatedI am running OS X version 10.7.3.My router is the time capsule. Have wireless in house, no problem. BUT, just bought a Denon AVR 1913 stereo with wireless built in, but it requires ethernet hookup to router or a wireless bridge. I Have Linksys Cisco Dual-Band Wireless-N Gaming and Video Adapter (model WET610N).Its firmware is out of date and newest version is required due to difficulties with latest version of Mac os x.I cant install WES610N to update it.
View 1 Replies View RelatedI recently linked my dtv receiver to the internet through my laptop. My question is, since I'm now sharing the connection, do I need to make any adjustments in the "network and sharing center" to keep sensitive info on my laptop safe?I do have Norton Internet Security.
View 1 Replies View RelatedJust updated my DTV to a HD receiver which has the ability to access movies/shows via internet so I hard wired my belkin router to the TV receiver and I can't get it to connect. The router light does not go on showing me I am not connecting to the TV receiver. When I go into the DTV receiver it reads all my IP address and has an OK behind them, but says there is an error and the internet is not connected. When I plug the same cable into my PC or my laptop the light on the router does come on. Also my iphone does receive WIFI via the same router. I called DTV and they said everything on the receiver is correct. I called my router folks and they said everything is correct and that it must be the DTV receiver. I've been using this router for several years and their tech guy sounded like he knew what he was doing. how I can get the router to recognize the TV receiver?
Here are my router settings: I used the WAN IP info in my TV receiver. Home| Help| Logout Internet Status: Connected LAN SetupLAN SettingsDHCP Client ListInternet WANConnection TypeDNSMAC AddressWirelessChannel and SSIDSecurityUse as Access PointWireless BridgeFirewallVirtual ServersClient IP FiltersMAC Address FilteringDMZWAN Ping BlockingSecurity LogUtilitiesParental ControlRestart
[Code].......
I need a vpn address for Digital satellite receiver TITANIUM HD 20000.I have tested several address which are working on my pc windows but my satellite receiver can not connect to vpn server. what should i do?
View 5 Replies View RelatedOld Configuration:
A 2 Wire 2701HG-B DSL MODEM/Router Upstairs
Wired into 2 PCs upstairs
WiFi to a PC Downstairs.
I killed the DSL service and got U-verse, but that added a new Modem/WiFi downstairs. I still have the 2Wire upstairs, but it has no phone connection.Can I use the 2Wire to "Receive" and "distribute" the WiFi signal from downstairs?
I don't see how to turn off the DSL MODEM. If I put in the ID and Password for the WiFi router downstairs into the 2Wire upstairs, will it "Login" or will it conflict? Are there special settings for the PCs to access the U-Verse router through the 2Wire?Basically, I want to know if the upstairs 2Wire can receive the U-verse signal and convert it to wired signal for the 2 upstairs PCs.
I am in a community that has a wifi system and the club house is about 900ft awayWhat king of a receiver would I need to reach and receive that signal?
View 2 Replies View RelatedI want to use a D-link WB-2310 wireless router to receive a wireless signal. Downstairs, connected to a cable modem (11MBPS), is an intel iMac running 10.4 that can send out its own wifi signal (internet sharing). Upstairs will be a PowerPC G5 Mac running 10.5 that has no wireless card...I was hoping I could use the router in place of a wireless adapter.
View 3 Replies View RelatedI have a Class HD 9000x 2USB TV receiver. It comes with a wireless connection. I am not able to connect it to my wireless router. When I try to connect it to the wireless router it says "No Wireless device" Although all other wireless devices (Labtop, Mobile) are working fine. I think there are steps to activate the network connection on the receiver.
View 15 Replies View RelatedI am sharing wifi with my sister from apartment directly above hers...I can get the wifi and use it for my laptop/computer but have been having trouble keeping it stable for to use it as an internet connection for my satellite.I bought a Netgear wnce2001 (wifi to wired) and it works ok about half the time....the other half the signal is simply to weak to even register the IP address on my satellite receiver.Is there anyway to increase the signal on my end...you know, without having to add a bunch of new gadgets?
View 6 Replies View Relatedi want the Satellite receiver to be wireless.i have a I-Link 9000 Plus Satellite reciever which has an ethernet port , where the buffalo router will be connected. (Buffalo WHR-HP-G300N Firmware: DD-WRT v24SP2-EU-US My main router is the Linksys Wireless G router WRT54G2 V1.5.
View 2 Replies View RelatedI have an old PC in my Buenos Aires apartment, connected to WiFi by means of a receiver module - because the modem is across the room and too far to connect by cable...But I get the message that the device would work more efficiently with a high-speed USB port...If I installed a high-speed card inside the computer, would this improe my Internet speed? It hangs up quite a bit... but then again, it's a Pentium III, so there's that limitation too.
View 1 Replies View RelatedI have no system. I bought just the cameras @ a yard sale 4 a $1. I want @ hard wire them @ PIP on my TV via RCA cable.
View 12 Replies View RelatedJust picked up the Yamaha rx-v867 receiver a few weeks ago. It has an ethernet port so that it can do internet radio (Pandora, etc). Not close enough to the router to go wired. I am getting an old 802.11b router from a family member today. Can I use this as a bridge to send music over the wireless network to the receiver? What steps to successfully setup?
Usually I set up wireless networks with laptops or pc's with wireless cards.
can i connect a wireless security camera to a computer without its receiver
View 1 Replies View RelatedI have a Belkin f5d7234-4 lying around at home. I also have a Panasonic TV which requires a proprietary wifi donge to get a wireless signal, so my question is, can I use the router to recieve my house Wifi (broadcast by my new NetGear Router) and send it out through its Ethernet port to the TV?
I checked, the router doesn't have ddwrt support, I'm new to hacking around with routers and networks, so I don't know how to do this, I see how it is logically possible
I want to connect my satellite receiver to my modem through Ethernet cables. First connect the modem to Ethernet outlet using standard small Ethernet cable.connect Ethernet outlet A to outlet B using Ethernet cable inside the wall.connect outlet B to the receiver using standard small Ethernet cable.I want to know how I make the connection in outlet A and outlet B to make this work.
View 3 Replies View RelatedI have bought 2 white single ariel recievers for wireless xbox live and red light stays on both so cant be them so what am i doing wrong , i have had it working on a cable but not wireless
View 1 Replies View RelatedI'm trying to configure an snmp notification reciever on WCS 7.0, so that critical alarms get reported to our central console. Following the configuration guide I was able to add the reciever as northbound, but after adding it I get an alarm saying that it is unreachable by WCS so all alarm notification will be suspended. I have tested snmp and ping connectivity between the WCS box and the notification reciever and it works ok, is there some other traffic that I might be missing?. I've seen some packets going from the WCS box to TCP port 7 on the reciever, which as far as I know is the echo service, is that what WCS uses to test connectivity?
View 7 Replies View Relatedits possible use citrix receiver for java on asa 5505 on ssl web vpn?
View 1 Replies View RelatedI have lost my receiver to a wireless mouse and key board of LOGITECH K260. kindly tell me what should i do to resolve this problem. can i get its replacement from market?
View 1 Replies View Relatedcapturing high-quality audio (44.1 kHz, 12+ bits) and send it over WiFi to a receiver.
Microphone->[Audio module+Transmitter] -> Wireless Link -> Receiver
I have a Vizio smart tv with built in wifi. I have Centurylink dsl service with a Westell 7500 gateway. All of my wifi devices, including my tv can access the internet appropriately. I also have a wii connected to my tv which can access the internet via wifi. My question is---is there anyway to setup an internet connection to my directv hd receiver using the wifi connection through my tv or wii? I really do not want to buy anymore equipment and I only have one phone line run with dsl service.
View 1 Replies View RelatedIs possible to setup DIR-655 as a Wireless receiver passing the signal to the other devices by ethernet?
View 2 Replies View RelatedA 2960G switch is doing IGMP snooping and is configured as the querier. There is no multicast routing.
Port 1 - Video Set Top Box A
Port 2 - Video Set Top Box B
Port 3 - Multicast Source
Both Set Top Boxes A & B are set to receive the video delivered in the same multicast group.Every 60 seconds the switch generates an IGMP General Query message which is sent out all the ports in the VLAN.There is a 10 second timeout in the Query message. Devices that wish to join (or remain joined) to the multicast group have this amount of time to respond with a Join Message directed at the multicast group. Devices deliberately wait a random duration within the timeout time before replying.
For some reason (which I don't understand), if the switch receives a Join request message from a Set Top Box, it forwards that messages out of the port to the other Set Top Box. So, let's say Box A responded with the Join Message first. Box B now sees the Join message and now thinks there is another multicast receiver on its branch of the network, so it suppresses its Join Message to avoid sending an unnecessary message.If by chance Box A responds first 2 or 3 times in a row, the switch will not have seen a response from port 2 for awhile, so it prunes that port from the multicast. Eventually, Box B responds first and gets re-joined onto the multicast. It is now Box A that may get pruned if it is consecutively slower.
How do I prevent the switch from replicating the Join message out to the other Set Top Box? I have verified this behavior with Wireshark. But, I believe the Join message is only supposed to be forwarded to a multicast router (if there is one - and there isn't), not to other ports.The 2960 is running 12.2(58) SE2.
I am having trouble locating and installing my pci receiver card driver using windows 7 64 bit op sys
View 1 Replies View RelatedI have some 1080p video files on my PC. Since my PC isn't powerful enough to play the files smoothly, I have been streaming the content to my PS3 using Windows 7 media sharing.
This works well with no noticeable loss of quality.
My problem is that I have to go into the services on my PC and restart the WMPNetworkSvc service every time I switch the PS3 on, otherwise the PS3 doesn't detect the PC.
how to make this a permanent arrangement?
Is it possible to convert multicast streams (224.0.0.1:1234) to unicast (Receiver 10.0.0.1:1234) at the router level.
View 4 Replies View RelatedFor my work I am looking to create wireless capabilities to remote locations. To do this we are using a standard modem/router that is connected to an Engenius (802.11b/g) wireless outdoor radio connected to a dish antenna. We are able to go to locations (3+km) and then with a corresponding receiving antenna (using LoS), receive the Internet and connect both to computers at the transmitting point as well as to the WWW. The problem exists is that we want to employ a series of routers at the receiving end that would be able to carry the transmission to a different location (relatively close), due to the fact that some of the locations do not have line of sight to the antennas. We are using Encore routers, model # ENHWI-N3. When we connect the radio's Ethernet into the routers WAN reciever, we can connect to the Internet with a computer. The problem exists is we want to pass that connection over to a second router (R2). This connection is done when the routers are on access points set to a WDS function with R1 having R2's mac address and vice versa. Both routers are set to channel 1. Even when the routers are seperated by distances >50m a computer plugged into R2 can see a computer plugged into R1. Files can be transferred between the 2 computers wirelessly at speed around 3 mbps. However computer 2 on R2 can not connect to the WWW. This router features a spot that lights up if it has Internet access and R1's is lit up but R2's is not. How do we transfer the Internet and not just a LAN from R1 to R2 so it can be accessed further away from the point of the radio and antenna equipment. This setup has also been used where R2 is hardwired to R3. At R3 we change the channel to 11, and then connect through that with mac addresses wirelessly to 4th router. If comp is in R4 and far away it can still access and file share from comp at R1.*edit the ip address for the routers exist all on 192.168.1.xxx If the 3rd number is different between routers would this make a difference?
View 1 Replies View Related
