New Cisco E2000 (wireless N router) not compatible with WMP54G (2.4GHz) adapterCan't find new drivers. Crashes computer to blue screen. Can the two be made compatible? Windows XP Home and Pro (both computers have WMP54G and blue screen).
View 4 RepliesEssentially when my friends computer disconnects from the router, everyone elses computers cannot access the internet, even though windows says they are still connected.
View 1 Replies View RelatedDSL Modem>E4200>100' Cat6>SE2500>6' Cat6>Dell XPS 420 Windows 7 In this setup windows 7 crashes everytime about 2 mins If I go Cat6 to computer there is no issue at all The first 6' cable I used would only give a 10Mb connection The second 6' give 1Gb but still crashes everytime The E4200 has only to ports used one for the SE2500 and one for a Cisco SD2005 The SD2005 is connected to a Revue, Squeezebox, Sony BDP, and a Dish Network 722 I am also using WET610N to a trendnet 4port switch with a Dish 922 and a Sony BDP which I am tring to eliminate the WET610N by hard wiring everything. This is the purpose of the new ES2500.
View 1 Replies View RelatedDSL Modem>E4200>100' Cat6>SE2500>6' Cat6>Dell XPS 420 Windows 7 In this setup windows 7 crashes everytime about 2 mins If I go Cat6 to computer there is no issue at all The first 6' cable I used would only give a 10Mb connection The second 6' give 1Gb but still crashes everytime
The E4200 has only to ports used one for the SE2500 and one for a Cisco SD2005 The SD2005 is connected to a Revue, Squeezebox, Sony BDP, and a Dish Network 722 I am also using WET610N to a trendnet 4port switch with a Dish 922 and a Sony BDP which I am tring to eliminate the WET610N by hard wiring everything. This is the purpose of the new ES2500.
I have the WMP54G internal wireless adaptor. It normally works fine, but I have been having problems with it lately when I turn my computer back on from sleep. Even thought the wireless router works just fine, when the computer wakes up from sleep the adaptor does not seem to detect any network. I have to restart my computer, and then the adaptor detects the network.
View 1 Replies View RelatedI'm trying to install a WMP54G PCI Version 4.1 in my Windows 2000 Pro SP4 computer. I ran the setup cd before installing the card, then took out the disk. After installing the card and powering the computer, the Available Wireless Network screen didn't appear. I also didn't get the Network Monitor icon on the taskbar. Network Monitor appears in the start menu, but can't be started. Device Manager says the card is working properly and there are no conflicts.
I uninstalled the software, removed the card, and repeated the installation process with the same end result. The card light blinks like it is receiving data. I'm using a Linksys WRT54G2 router. Both my desktop (W7) and my laptop (Vista) connect just fine. How can I get my W2K computer on the network?
Can i move my linksys e2000 router to a new computer and if so how do i go about it
View 2 Replies View RelatedI have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
View 3 Replies View RelatedI have a problem with my download speed. I'm supposed to have a speed of 60 MBPS and when I collect my computer direct to the modem I received it but with my e2000 router, the 3 computer connected to it can't reach more than 30 MBPS. I just updated the firmware of the router to the newest version but nothing changed.
View 2 Replies View Relateduupon starting my computer a blue screen appears and it crashes, I shut the entire system down and restart in safe mode.
View 1 Replies View RelatedIf I have anything else connected to the network (anything being my Xbox 360, or my smartphone) and I turn on/wake up my computer, the entire network crashes and I have to power cycle the router and modem in order to get it to work again. What would even cause this? I often forget to turn off the wifi on my smartphone before I turn on the computer, which results in a lot of very tedious power cycling. It's also frustrating if I'm playing some vidya on the 360 and my wife gets on the computer, resulting in me getting kicked off and her unable to even do what she wanted to do in the first place.
The stranger part is that if I have my computer already on, and I turn on the 360/smartphone, it works fine. So there's something going wrong in the process of my computer connecting to the network, I guess. I have set a static IP, and I also made sure to turn off the energy saving feature of my wifi card, but neither of those things solved the problem.
I have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
Any issues on Cisco ISR / ISR G2 routers running 15.x code while doing NAT for large quantities of users (3000+) involving lock ups? This seems to be an ongoing issue for a customer. The symtom is present on 2811, 2911 and a 3945. The 3945 never spikes over 10% processor or memory utilization, yet still has these issues. The routers have been tested running 15.0(1)M5, 15.0(1)M7 and 15.1(4)M4 which all showed simular results. Other router side services are running such as NetFlow v9 to two destinations. Another interesting symtom, doing a "show ip nat translations" command will crash the router if executed at its peak usage period. NAT is to a single IP (sourced from outside interface), not a pool.
[code]....
I have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies View RelatedI saw a thread from early 2010 which described the issue I am currently having to a T. I am on a Belkin Wireless G with Mimo router and it runs perfectly either on LAN or WLAN, until my new roommate's MacBook gets on there at the same time. As soon as the MAC connects, I get a blue screen of death and the PC restarts. I have been battling this issue for over a week now and have absolutely narrowed it down to the Mac/wireless area.
I have already uninstalled/reinstalled my wireless drivers and thought that had fixed the issue(it worked fine for 4 days), until the roommate returned from out of town and connected the Mac to the Wireless....then WAMMO, like clockwork, back came the BSoD. This seems like a very unique problem, as I have done many searches online and the one I mentioned on here is the only one I could find that accurately described my issue.
For reference, I have posted the link to the previous case below. Unfortunately, no solutions, other than reinstall drivers (which I have already done) are posted. I tried everything in that thread and my settings appear to all be the same as his. Is it possible this is just some rare Windows 7 glitch that has never been resolved?
[URL]
I have a wgr614 V6 router, yes its old. I had 3 devices connected to it just fine before without any issues. But now It only allows my laptop, when I try to connect with my ipod touch or desktop, not only does it fail, the entire network crashes and my laptop loses it and its gone. It then takes about 2 minutes to come back up. So whenever I attempt to connect with another device the network crashes. so right now only my laptop is connected.I downloaded & updated to the newest firmware, did not work.I tried resetting the router, and made the network all over again, did NOT work.
View 7 Replies View RelatedI have a D-Link DIR-615 router, hardware version E3, firmware 5.10
When I go to get a list of servers when playing games online, my router lights up and then crashes, and I cant get on the internet again until I exit the game. Although, some games do work. There are no problems with my firewall, and if I connect directly to my modem, I can play fine.
We bought a cisoc 2911 Router with an EHWIC-VA-DSL-A Card. I did the Dialer Setup without any problem but if i set the ATM interface with the commands: [code]The Router crashes after some seconds. I didn't connceted the phone line to the DSL card. [code]
View 5 Replies View RelatedI have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
In hopes of fixing some "flaky" connection issues with my WRT54G V2 Wireless Router, I downloaded and applied the new firmware version released on 08/18/2011, Ver.4.21.4 for my Version 2 Router. I downloaded, went through the application process using the router's firmware update process, it said it was successful and then the router restarted and didn't work. Couldn't ping the address, constant flashing Power light, no response at all from router. Tried again, same result. Performed hard reset, same result. Tried a few other recovery techniques found on the web with no success. Finally I did the process found here [URL] This reset the router and I re-uploaded this same 2011 version. Router still broken. I ran through the process again after downloading an older version of the firmware, specifically version V3.1_4.00.7, the upload ran, and the router worked again! This was proof to me that the newest version completely BRICKED my router. I'm so relieved I was able to reset the router and manually recover, but most will never try this. I recommend Cisco retest this ASAP and pull the new release for the V2 router until they get this resolved!
View 9 Replies View RelatedDriver download for this pci adapter?
View 1 Replies View RelatedI am attempting to setup a wireless access pointand want to deny access to a group of IP addresses. When I go to Wireless, MAC setup, Deny or Allow, and select "Edit MAC Address List" my browser crashes. I have tried this on two different Linux systems and three browsers, Firefox, Mozilla, and Seamonkey.Tech Support tells me to downgrade to Firmware version 4.30.2, the only compiled version available on the Linksys website, but with no way to go back to 4.30.5 if the problem isn't fixed or if worse problems come up I am reluctant to try this fix, The only other suggestion Tech Support offered was to replace my WRT54GL with a WRT54G.
View 3 Replies View RelatedMy WAG320N has developed a fault where by after 1, 2, maybe 3 clicks on the web interface and the router reboots. The browser can no longer connect until it is closed and reopened (firefox). Firmware is: v1.00.12
Interestingly, if I use a different browser it doesn't seem to reboot and I can click away for ever. However, firefox reproduces the problem every time. FIrefox version is 7.0.1
I recently upgraded the firmware from 2.0.2.1 to 2.0.3.3 and when the router rebooted the interface was missing many items. On the basic setup page the boxes were missing to set the local ip address, subnet mask and anything below that. On the Wireless Security page the security mode box was half it's size and did not have any options in it. The wireless isolation wpa algorithm, preshared key and key renewal boxes were missing too. I rebooted the router and still got the same thing. I was able to get into administration and reset to the factory default. Once the router rebooted I was unable to get into the interface at all. It wouldn't come up at all. The power and light were blinking but I was unable to connect to it. I tried to connect with 192.168.1.245 and the one I had set manually but no luck with either. I was able send back the router for an exchange with Cisco. I received the new one today. It started up and everything worked great. I decided to try the firmware upgrade again. I went from the firmware version that was on there(I didn't right down) to 2.0.2.1 and the upgrade worked as the other 3 I have. I than tried the 2.0.3.3 upgrade and I got the same thing as the other router I sent back. I have 3 other routers in place that I will not be upgrading at this point. I should not have tried the upgrade again on the one today but being a bank the examiners like everything up to date and it's part of the monthly check.
View 2 Replies View RelatedI seem to be experiencing a problem with content filtering on our 1941, if I add anymore patterns to the policy below the router crashes and requires a reboot, not sure why?
parameter-map type urlfpolicy trend cptrendparacatdeny0
max-request 5000
max-resp-pak 1000
[Code].....
For a while now, my wireless network at home has been very unreliable. I posted on these forums before, asking for assistance to fix crashes that seemed to be random. I was largely unsuccessful, and the problem continued. However, as I continued to experiment with different methods to keep my network up and running, I noticed that as long as I had at least one device connected to the network around-the-clock it never crashed. This was easy enough, as I own an iPod touch and a dock (I would leave it sitting it the dock unlocked all the time). But it's annoying to never be able to leave the house with it, and I'm ready to finally get a solution to the problem once and for all. I would prefer not getting a new router, but if worse comes to worse I will.
To sum it up:
-Works perfectly (when up) at full speed, never crashes unless there are no devices connected to it.
-When it does crash, it is very difficult to 'coax' it back into working again; it's been down for weeks at a time before.
-For some strange reason (and maybe this is a clue), newer game systems such as a Nintendo DSi or PS3 can make it start working again. I, of course, own neither of these.
-I'm using a WRT160N V3, latest firmware as far as i know.
I am experiencing loss of internet access when browsing to amazon.com. In addition to losing internet access, I am unable to connect to my BEFSR81 router when this happens. To resolve I have to walk over to my router and reset it by cycling the power.
This issue has been reported by other users of the BEFSR81 too: URL
Details: My BEFSR81 is version 3.0 and is running firmware version 2.51.4
Just got a wmp54g card from a friend w/o the disc, where can I find free driver downloads to set it up?
View 5 Replies View Relatedmaking Windows 7 do what it's supposed to? Seriously, there needs to be a button you can click to roll it completely back to XP.
View 1 Replies View RelatedI recently re-installed Windows on my PC, and I had the Wireless-G PCI Adapter installed before I done the re-installation.Now I've re-installed Windows, the adapter doesn't work. Do I have to re-do the whole process again? Also, I didn't actually install it myself, so any detailed step-by-step tutorial?
View 3 Replies View RelatedI am having some trouble getting my computer with Windows XP to use the Linksys model WMP54G wireless - G PCI adapter to connect to the network in my house. I have installed the hardware and the drivers. When I open the view available wireless networks window my network shows up with two bars of strength. But when I select this network and click connect, I get an error message saying "Windows is unable to connect to the selected network. The network may no longer be in range. Please refresh the list of available networks, and try to connect again." I have other computers connecting to this wireless network without any problem. The wireless router I am using is the model WRT150N wireless
View 6 Replies View RelatedMy router is located in my living room and my desktop is in a room located some 30 fett away with several walls in between. I am a light user (surf internet, read emails) and I do not have any special requirements.My router is a WRT54G router and my Wireless-G PCI Adapter is a WMP54G. Both have worked well for the last 5 years or so. Unfortunately, I had some work done in my room and the workers have broken the antenna on my desktop PCI adapter.What should I buy to replace my WMP54G?Should I get a PCI adapter or an USB adapter? Which one?Reliability, range and ease of use are my priorities. Price is not a major concern.
View 1 Replies View RelatedI just recently upgraded my OS from Win XP 32 bit to Win 8 64 bit. I am trying to get everything in order and most of the drivers are now working (CCC for my graphics card, driver for my Striker). However, I am having difficulty locating the driver for 64 bit windows for my Linksys adapter.
For the moment I am running wifi by using my old XP setup (which is the only way I can post on [H]). :P