Cisco 2960 Router Configuration?
Feb 15, 2012I have a serious problem with cisco 2960 router,i am using a dell dimension 3000 running a microsoft windows xp proffessional.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2960-S To 2960-LST Configuration Over Fiber?
Feb 11, 2013I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedCisco Switching/Routing :: 2960 / 1801 - Switch / Router VLAN Configuration
Jul 5, 2012I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
Cisco WAN :: 877 / 2960 - HSRP Configuration On VLan1
Nov 13, 2012I have the following topology:
2x 877 routers, one interface from each router (port Fa0 which belongs to the router internal switch) is connected to the 2960 switch, the switch himself configured with default settings, flat with one v LAN.
I have configured HSRP in the following manner: router A is 10.0.0.2, router B is 10.0.0.3, virtual IP is 10.0.0.1, take note that the HSRP configuration along with the IP address are configured on vlan1 interface.
Now when i connect a PC to the switch with static IP (10.0.0.4) and trying to ping 10.0.0.1 I'm not getting replies. i see on the PC, using wire shark, the icmp request goes out but on the primary router (and also on the backup) i can't see the icmp request (using debug ip icmp).
this behavior happens only when the HSRP is configured on interface vlan1, when configuring the same configuration on Fa4 (which is WAN interface) everything works fine.
Cisco Switching/Routing :: 2960 Configuration From A HP 2510
Jan 17, 2012At a college we have Ciscos 2960 and are trying to setup VLAN tagging and also using RST or MST. The traffic on the jack should get tagged vlan 248.We were told by the college that Ciscos in the labs will not work with the Alcatel switch that provides access to the lab. That Alcatel is in Bridge 1x1 mode. The college will not change the configuration on the Alcatel.We got the Ciscos to do VLAN tagging and can get network access. However the spanning- tree is not read properly. Cisco does not properly read the Alcatel's RSTP (since the Alcatel is doing tagging on the BPDUs). It places the root of the spanning tree under vlan1 instead of vlan248.
The college strongly recommends HP Procurves and we are using that as test.The following is the configuration on the HP and it works with no effort (it reads the spanning-tree information as MST)We will end up getting HPs instead, if the Cisco cannot work with the Alcatels.
Cisco AAA/Identity/Nac :: 2960 Configuration Combination Not Working
Mar 3, 2013We have a configuration that work fine but one of the combinations it don´t work. When we connect a guest laptop, the first time work fine. The configuration is when the laptop don´t authenticates with radius, the dhcp server assigned vlan guest and ip guest. The first time was ok. After, We connect a laptop with users authenticates work ok, the radius asigned vlan of users and dhcp server assigned ip users. The problem was when we connect for two time a guest laptop, radius didn´t validate and laptop didn´t negociate ip with dhcp server. In this time, the administrator of dhcp server, tell us that they didn´t see nothing traffic of my mac. and anymore run fine. If Whe change the port of switch , the laptup start working again.
Radius=NPS
Server dhcp: is typical.
Our scenario is with a ip cisco phone. the ip phone don´t have the authentication. The administrator of radius tell us that the configuratation is fine and the configuration of dhcp is fine. When we connect only laptop, everything run ok.
Configuration Port.
interface GigabitEthernet1/0/3
switchport access vlan 202
switchport mode access
[Code]...
Cisco :: Save Configuration File On 2960-48PST To FTP Server?
Feb 25, 2013I'm trying to save a configuration file on my 2960-48PST to a FTP server.
Unfortunately it doesn't work. What different steps I should follow ?
The software version is 12.2(50)SE5.
Cisco Switching/Routing :: 2960 Switch Lost Configuration
May 5, 2013I have a 2960 that bounced several times over the weekend and then appears to have lost its configuration. Using CDP from the backbone switch pulls up the information below. Is there any way for me to configure the downed switch from another switch on the network? I am trying to avoid having someone from the site try to find a console cable and a suitable computer with a serial port. [code]
View 2 Replies View RelatedCisco Switching/Routing :: DHCP Configuration For 2960 Switch?
Oct 21, 2011I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
Cisco Switching/Routing :: 2960 Multiple VLAN Configuration?
Mar 11, 2013Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies View RelatedCisco Switching/Routing :: 2960 / 3750 - Best Configuration For This Scenario
Jul 26, 2012I'm fairly new at trying to create isolated network segments on Cisco switches. What I'm trying to do is have multiple isolated paths that originate from my v Sphere infrastructure travel through a layer 2 link, v LAN, up to a MLS, and ultimately out to to the internet through a firewall. Each sub net might ultimately have a number of hosts on it, but I don't think the make up of those hosts will matter here.
My initial thought was creating v LAN tagged port groups on v Switches on my v Sphere infrastructure. Physical connections will go from my ESXi hosts to the 2900 series Cisco switch connected to trunk ports. Both v LANs would be configured on the switch but not assigned to physical ports. The physical connection to the 3750 would also be a trunk port connection from the 2960. The 3750 would have SVI's created that are attached to VRFs that would control route traffic. This might be totally wrong but from what i've read it seems to be going down the correct path I think.
Two part question, is this the best way to go about designing this network? If so I seem to be really struggling with the SVI/VRF part. Every time I create an SVI all of my hosts on the 10.10.10.x network can ping them, regardless of which v LAN they're on.
I just cannot seem to isolate the 172 network.
Cisco :: 2960 / 3750S / 3750X / 6504S - SNMP Trap Configuration
Sep 10, 2012I have Cisco 2960's, 3750's and 3750x's all running IOS on the access layer. I have Cisco 6504's running IOS on the Distribution and Core layers. I am looking to monitor redundant links through Spectrum by having specific ports send traps but I have run into trouble finding how to configure it. I would like to have:
1. Logging enabled for all links (Fiber and Copper) so that I see all links up/down messages in the syslog
2. SNMP traps sent for linkup/link down messages only for redundant links (ex. Dual Up links from Access Layer or Redundant Ether channel Links on Dist Layer)
3. SNMP traps should be ignored/not sent for all copper ports.
Cisco Switching/Routing :: 2960 NTP Server / Client Configuration In Switches
Feb 28, 2012We had core(4503), distribution(3750), and access switches(2960) in our environment. Currently we configured the clock manually in each switch, but a reboot of the switch resets the clock also. We are planning to make a single switch as a NTP servers and others are clients to synchronise the correct time even after a reboot of the access switches.
View 6 Replies View RelatedCisco Switching/Routing :: Force Catalyst 2960 To Ignore Startup Configuration?
Feb 4, 2013I was wondering if I can force catalyst 2960 to skip startup config stored in NVRAM and boot with no config everytime it is powered. I tried to find it on google and in cisco white papers but still no luck. I found only commands that begin with "set boot config-register ... ", but switch acts like it does not know these commands.
View 7 Replies View RelatedCisco Switching/Routing :: Static Smartport Macro Configuration Of 2960 And 3750
Dec 4, 2011How do I create static smartport macro on Catalyst 2960 & 3750 equivalent to below static smartport macro:
macro name NOT_USED
description UNUSED_PORT
switchport
switchport mode access
switchport access vlan 100
shut
@
I am able to create above smartport macro on Catalyst 3760 & 6500, but not on 2960 & 3750 (see below):switch(config)#macro ? auto Macro autoexecution settings global Enter global macro configuration
Cisco Switching/Routing :: Catalyst 2960 / VLAN Configuration Using MS DHCP Server
Jan 28, 2013I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
Cisco Switching/Routing :: 2960 POE Switch Voice Vlan Configuration To Work With Non IP Phones?
Apr 12, 2012provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
Cisco Switching/Routing :: Add 2960 To Stack Of 4 X 2960 Switches
Feb 7, 2012I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedCisco WAN :: 2960 / Internet Access Router Acting As DNS Server
Nov 25, 2011I have a design for my infrastructure and i'm thinking to choose 4 or 5, or more, 2960 series in a stack mode instead of one 4500 series?
View 4 Replies View RelatedCisco Switching/Routing :: 2960 / Bridging On Router Sub-interfaces?
Aug 13, 2012I need to bridge 2 subinterfaces; F0/0.301 and F0/0.302 on a single router.The router interfaces with a Cisco 2960 (LAYER-2) switch.QUESTION is, does a Cisco router support bridging on subinterfaces on the same physical interface?Currently this is NOT operational Spaiing-tree on F0/0.301 and F0/0.302 is down, switch side is forwarding for both Vlans.show ip interface brief shows up/down status of F0/0.301, F0/0.301 and BVI6 is down/down?
:
SETUP:
bridge irb
!
!
Interface F0/0
no ip address
[code]....
Cisco Switching/Routing :: Flapping Between Router (2811) And Switch (2960)
Jul 23, 2012we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
Cisco Firewall :: How To Configure 5510 - 2611 Router / Two 2960 Switch
Dec 29, 2012I have one Cisco ASA 5510 with 2611 router two 2960 switch how to configure.
View 1 Replies View RelatedCisco Switching/Routing :: 2960 - Connecting Two Vlans To 1 ISP Router Interface
Dec 19, 2012I have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
Linksys Wired Router :: Vlan Trunking 2960 And 2950 Switches
Feb 18, 2011I have a number of class-'c's as a hand-off from my data center fiber to my 2960, which then sprawls the racks with about many 2950 switches, mostly 20 machines per switch. To allow machines on one 2950 to push data to another 2950 without routing back to my ISP's router(which costs money for bandwidth) isn't is possible to trunk one port on each 2950 to another 2950 and adding a addititional vlan8 to them. Then data jumps from 2950 to 2950 without going back to the 2960 or mainly not going back to my ISP's router. Is this the correct way to accoplish this with extra vlan and trunking the 2950's to each other or am I looking at this all wrong?
View 1 Replies View RelatedCisco Switching/Routing :: Router Is Connected To Switch 2960 Configured As DHCP SNOOPING
Sep 3, 2012We have a DHCP SERVER implemented in a cisco router 2610.This router is connected to a switch cisco 2960 configured as DHCP SNOOPING. At the switch appear the next log message: [code] The ip address: 10.100.200.1 belongs to DHCP SERVER configured at router cisco 2610. What to do so these log messages does not appear any more? Do I need to do some configuration changes at some switch or router?
View 11 Replies View RelatedCisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration
Jul 17, 2012I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration
Dec 14, 2012I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedLinksys Wired Router :: Proper RVS4000 Configuration Behind A 3rd Party Router
Mar 16, 2011I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies View RelatedCisco :: ASA 8.4 - Getting NAT Configuration Through Router?
Oct 6, 2011I have a nat configuration to apply on a 8.4. I am a bit confused.On a ASA 7.0 the configuration is as such static (inside, outside) 10.102.247.0 10.102.247.0 netmask 255.255.255.0Basically, I want a bidirectional nat .. for users to connect to the inside network using the real IP.object network Delta subnet 10.102.247.0 255.255.255.0,object network Delta
View 0 Replies View RelatedCisco 1841 Router - NAT Configuration?
Apr 8, 2011I have 2 cisco 1841 routers the one is connected to my local network and the other is the stub router and it only has 2 fastethernet interfaces. fao/1 connected to the local network and fa0/0 connected to the internet and to the other router. How can i configure NAT on the fa0/0 which is sharing the internet and local network
View 1 Replies View RelatedCisco WAN :: 2811 - Configuration Of Router And BGP
Nov 8, 2011I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
Cisco WAN :: ADSL Configuration On 887 Router?
Aug 1, 2011I am installing a Cisco 887 to a ADSL2 Circuit and I cannot connect to the ADSL eventhough the show interface shows that both the ATM0.1 and Dialler 0 is up.
The configuration of the router is below.
Building configuration...
Current configuration : 5980 bytes
!
! Last configuration change at 11:12:58 PCTime Wed Aug 3 2011 by cisco
[Code].....
Cisco WAN :: BVI Configuration On ASR1002 Router
Oct 14, 2012We have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies View Related
