My wifi connection seems to 'brown out' but not consistently. I just had comcast tech out yesterday and he said things seem good up to the cable modem.I just replaced my cisco e3000 with new cisco 4200. No problems when plugged into lan but my gut is telling me it still is in the "feed" and not the router. Anyway to track the latency of the broadband? See if if it comes and goes intermittently?
View 1 Repliesmy laptop (asus) has been having issues with my WiFi. On startup, the laptop will (usually) connect to the internet fine, but after a few minutes, usually without any specific cause, it will disconnect from the internet, and the toolbar indicator will go from full signal (full bars) to no bars and a yellow triangle, saying limited access. When I try to reconnect, it will say "connecting" for a few seconds and then will say "cannot connect". I have to leave it for a few minutes every time before it will randomly reconnect until the next incident... My other two pc's (one Windows 7 and one Windows xp) do not have this issue, but sometimes other wireless devices in the house (iphone, ipad) will have a problem where the WiFi indicator will show full bars but I will not have internet access. I have to disconnect and reconnect in order for it to work. Again, it happens sporadically with no obvious cause...
IPCONFIG Info:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
[Code]......
I've been having a problem with my wifi connection.I give my neighbor $15 a month to use his connection, so I have no control over the router.I'll be surfing along or just checking mail or whatever and out of the blue my connection stops. A little yellow triangle "warning" sign covers the signal strength meter in the lower right corner. If I click on the signal meter, up pops the list of wireless connections available to me and says that I'm connected, (but I'm not). So I go to the network and sharing center and sometimes this alone will restart the signal but usually I have to run the troubleshooter and the signal will come back with no explanation of what the problem is.While in the network and sharing center, my connection to the router looks clear and connected but shows a red X over the connection between the router and Internet.
View 3 Replies View RelatedI have a Linksys Wireless-N Home Router, WRT120N to be exact, and I have been having problems with my wireless. My wifi losses internet connection intermittently. This does not happen when I am connected directly to the router with a Ethernet cable. I have redone all the settings many times(like 6) and Im still having the same problem.
I really dont want to have to buy a new router
I have an ancient Compaq V2410 notebook which has started to drop my home Wifi connection recently (started about a week ago). At first, I thought it was the install of Firefox 8 as it froze and crashed but it happens with Chrome, IE and even when not running a browser.
My ISP is O2 in the UK and I have a DSL2+ service with the O2 Wireless Box II. I have gone through a power down cycle on the router and it continues to work with my ethernet-connected desktop PC. I have changed the Wireless Card in the notebook but fault is still intermittent. The notebook was also set to OpenDNS servers but that has been set back to Automatic DNS servers.
The notebook has the latest free versions of Avast Anti-virus & Comodo Firewall and the main issue is that the notebook has 640Mb system RAM which means that various Windows services have been Disabled or set to Manual.
I can sometimes recover the Wifi signal by switching the wireless on/off but it is sporadic. I have attached the Xirrus WiFi screenshots at startup, at fault state and at recovery state together with the ipconfig.txt output.
E4200 Version 2.0.37.131047 disconnects my wireless clients intermittently. I am seeing it mostly on the 5Ghz band but that is where most of my clients are connected. I have all the setting in advanced tweaked per cisco best practice. It just seems to reset every so often. Wired connection is not disconnected.
View 9 Replies View RelatedI'm trying to enable LAG between WLC and a Juniper switch EX-4200 but it is not working.
Â
In the lab i managed to enable LACP between Cisco 2960 and juniper EX-4200 and works with the atached configs that i found on juniper forum. Also LACP between Cisco 2960 and WLC works with te same config, but never between the WLC and Juniper. I've tried with passive mode and slow mode, always seems that juniper is not seeing the WLC BPDUs. I tried with WLC 4402 and 5508 both with 7.0 firmware.
I would like to explain my situation. My house has 2 floors. My broadband modem is on the 2nd floor. I have an ea 2700 linksys router there, connected to the broadband modem. However, i can't get a good wireless signal on 1st floor, therefore i bought a second router, an e 4200 linksys.
I searched the web, and connected both routers via Ethernet cable, plugging them in lan ports. The ea2700 was only configured wireless security passwords. The e4200 had it's ip renamed to 192.168.1.2 and DHCP server turned off. Well, i have a problem here. the second router, doesn't give me access to internet.
I had windstreams modem "speedstream 4200" but parents for whatever reason thought the 4300 would change everything. With the 4200 I was open for gaming, could connect. With this 4300 I can't connect to anyone at all. I disabled DHCP server in my rotuer and that aving more fails than succeeds. (in connecting to people).My router doesn't have bridge mode but my modem does, I don't know what it does in the modem. My friend had the exact same problem I did and he put his router in bridge mode which I do not.
View 13 Replies View RelatedI have a small network of computers and printers in my tax office and consist of three computers running in window xp professional, one computer is designated as the server workstation and the c drive is the share drive and the other two work stations are mapped to the share drive c on the server workstation . so i am using peer to peer networking and these three computers are connected by a seven port router and two other printer are attached to the router also. i am having a problem printing from the computers to these printers, one is a hp laserjet 4200 and another is a hp laserjet all in one 3055.
In the past i just click and i would print, but a few day ago when i click print from either workstation it would que it to printing but it would have a message that it could not find my printer on the network. dont know why it all of a sudden stop working. do not know anything about setting up a printer on a network. do note the printers are connected to the router and not directly to the server workstation computer via usb. So the two workstation and the server workstation have the printer software on the C drive of each computer but for some reason it could not find the printers on the network. How to network a hp laserjet 4200 and Hp laserjet 3055 in a network that is connected by by one seven port router. why is the printers not in the network?
I have the E4200. I have two networks, a 2.4 for internet, and a 5gHz for media. I want to have a wired connection to the 5gHz network as some of the media is on my PC. However, it seems I can only have a wired connection to the 2.4gHz network. Is there any way to do this?
View 3 Replies View RelatedTo improve the security of my 4200 v1 router, I turned on in the router configuration "Access via HTTPS" and after the reboot I could not access my router via the browser even when I click on the browser message to continue. What do I need to configure either in the router or my browser to use HTTPS?
View 9 Replies View RelatedI have home network with my Linksys E-4200.
Â
My HP Microserver (Ubuntu +Samba+Apache) is connected via LAN. I have notebook (Windows 7). To my server (FILE+WEB) I have access only when I connected via LAN cable. In windows 7 i see my server and have access to the files. Webserver works also properly: access with the name of the server in web browser.
Â
But by WiFI connection, there is no access ! The server has the reserved local IP-address, like 192.168.1.200.
Â
What should I do to solve it? By typing "192.168.1.200" i see the localhost page, but nothing more!
My linksys 4200 was set up some time ago for me, (unsecured) and was working fine. I was having problems with just 1 desktop that was using a usb wireless adapter, so I went and purchased a new cisco ae2500. While connecting I used the push button that it described, only it knocked out the network, and all the other computers are now off of the network. The new network(s) are Cisco_WPS_42526 (secure) and Cisco_WPS_42526-guest. Not knowing the network key and the guys that set it up are gone, I tried the guest. WHICH REQUIRES A PASSWORD!!!! I can now not get ANY of my computers online! How do I find the security, or the password? Why would you need a password for an insecure network anyway?
View 2 Replies View RelatedI would like for Cisco to offer a firmware update for my 4200 so that the password for the guest account can be disabled.
View 1 Replies View RelatedWe are facing a major issue of VPN tunnel going down very often. I have 7 Site-2-Site VPN connectivity, this works fine for some days and suddently VPN tunnel goes down intermettenly for one or few locations and i need to clear isakmp sa for that speicific tunnel to come up.When tunnel goes down the vpn phase 1 status.....
 Â
6Â Â IKE Peer: 125.18.0.38
   Type   : L2L            Role   : initiator
   Rekey  : yes            State  : MM_ACTIVE_REKEY
7Â Â IKE Peer: 125.18.0.38
   Type   : L2L            Role   : responder
   Rekey  : no             State  : MM_REKEY_DONE_H2
 Â
After clearing phase 1 for specific tunnel the VPN tunnel come up.
Â
7  IKE Peer: 125.18.0.38   Type   : L2L            Role   : responder   Rekey  : no             State  : MM_ACTIVE
 CINBLR01-SQDR-FIREWALL-00002# sh version
 Cisco Adaptive Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)
 Compiled on Thu 07-Aug-08 20:53 by buildersSystem image file is "disk0:/asa804-k8.bin"Config file at boot was "startup-config"
 CINBLR01-SQDR-FIREWALL-00002 up 1 day 17 hours
 Hardware:  ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHzInternal ATA Compact Flash, 256MBBIOS Flash M50FW080 @ 0xffe00000, 1024KB
[code]....
This platform has an ASA 5510 Security Plus license.
I have WLC 5508 and 18Â 1242 APs are connected to WLC. I am getting following error messages in all APs.
Â
*Jul 3 02:53:18.263: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jul 3 02:53:18.320: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Jul 3 02:53:18.326: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to
[Code]......
We are having problems with using QuickVPN to connect to our RV220W.Sometimes it works, and sometimes it doesn't. There doesn't seem to be any rhyme or reason to it. [code] The firmware version is 1.0.3.5.
View 1 Replies View RelatedRecently been taking my Laptop installed with Win7 Pro to a Friends and was sharing his Wireless connection from Belkin ADSL2+ wireless router and notice that every now and again the wireless connection would drop out and the only way to regain a connection to the reset the router. My friends network has two laptops on it connected wirelessly with Windows XP home edition SP3, and a Desktop PC with XP also on connected to router Via Ethernet, also a Windows Home Server and XBOX 360 also connected by Ethernet, My friend since updated his laptop to Windows 7 Home Premium and is using the Wireless connection which now finds intermittent loss of connection which can only be restored by Resetting the Router. why a Router should lose connection just by connecting a Win7 laptop wirelessly or is there more to it than that.
View 3 Replies View Related[code] Whenever I am browsing online, every once in a while the internet just cuts out. It still says I am connected to my wifi network, but there is "limited or no connectivity." Whenever it happens, everything on the network loses its internet at the same time. In the household, there is one PC (mine), one Mac (my wife's), one iPod touch, and 2 iPhones that all connect to the wifi. The vast majority of the time, when this problem occurs, simply unplugging the router and then plugging it back in fixes the issue.Sometimes however things are different. Especially lately, I sometimes get an "IP conflict" error message. It says another device on the network is using the same IP address. Sometimes with this error simply unplugging and replugging in the router works. Sometimes the router has to be reset twice before things start working again with this error. The error doesn't happen every time the disconnect occurs, but it seems to be getting more frequent lately.Sometimes the disconnect happens when I am playing an online game that requires a constant connection to the internet. Sometimes this goes as usual, where a single router reset fixes the problem. However, sometimes this situation gets more complicated. One game in particular (League of Legends, if it matters) has this problem all of the time. When the internet disconnects while this game is playing, I do not get the "limited or no internet" warning. Instead, the computer seems to think that it is connected, and that the internet is working.
During this scenario, resetting the router once is never enough. After resetting once, the wifi reconnects and now it realizes something is wrong. After the first reset, the computer seems to "realize" something is wrong after all, and I am connected to the network but this time with the "limited or no internet" warning. A second router reset after this usually fixes the problem.Last night the worst disconnect happened yet. It was in the middle of a game, and the internet cut out, with no warning on the network. After one router reset, the wifi network reconnected immediately with an "IP address conflict" error, and then I was connected with "limited or no internet" on the network. I did the second router reset as usually required, but nothing happened. After a second and a third reset, there was still a permanent "limited or no internet" warning.I tried hardlining in directly to the modem and there was still no internet. Running the network diagnostic on my laptop fixed it however and I was connected to the internet. However, wifi still would not work, even after trying the diagnostic again. Running the diagnostic came up with an error that the DNS server was not responding and so nothing could be done.This time I reset everything. Unplugged both the router and the modem and left them unplugged for 30 minutes. When I turned everything else on again, same issue. Connected to the wifi network, but "limited or no internet." I unplugged everything again, left them overnight, and this morning after plugging everything back in the internet was back.A few final points I think might be relevant:
1) When checking the system event logs, it's usually a DNS error that I get (see event logs, 1st attachment).
2) This disconnect error seems to be more prevalent when more devices are on the network. As I said, they have gotten more frequent lately, especially the IP conflict warnings, since the 2 iPhones were added a few weeks ago. 5 months ago when it was only my PC on the network, these issues were practically non-existent.
3) It's a Belkin wireless g-plus router. Model # F5D7231-4 version 1213. It is an older router.
4) This has been happening for almost a year, but just recently gotten so bad I have to get this fixed, especially after last nights that could not be reset no matter what.
5) I'm not sure the disconnects have ever happened why the PC is not connected. That may not be relevant however, because my PC is almost always on since I work from home, while the iPhones, iPod touch, and my wife's Mac are only connected periodically.
6) This error has occurred while my PC is the only device connected to the wifi network, but it seems much less frequent.
7) The time the error seems most likely to occur is when another device connects to the network, such as when my wife first gets home from work. This is not exclusive however, and the DC's can happen at any time.
I've seen that people want ping tests and ipconfig /all tests so I will post mine. I will edit my post with the same tests done the next time this dc happens. I've also included a screenshot of that xirrus wifi program. [code]
Ap's at remote location intermittently joins unjoins the WLC controller 5508. AP's getting IP's from DHCP server located at locan end. [code]
View 8 Replies View RelatedWe have a Cisco ASA and recently purchased a cisco small business srp527 router. It is connected to our ADSL2 connection and is working fine. I have configured the device with an ipsec tunnel using an ike profile and the tunnel is created successfully with packets traversing the tunnel. However packets are being dropped intermittently, with no cause. The link is currently not being utilised, there is no load on the network however when I ping Google and any address subject to the rules of the tunnel i notice that a single packet is dropped every now and then.
View 0 Replies View RelatedI installed the RV220W Router in my office about 2 weeks ago and everything works perfectly for 3-4 days but then my connection drops out and the router must be restarted to restore connectivity. When I say the connection drops basically the internet connection drops out and my network connections drop shortly thereafter. Usually the wireless connections lose connectivity followed within a few minutes by the wired connections.
Â
Is there something in my firewall settings that could cause this issue? I have checked with my ISP to verify there are no problems on their end.
We just upgraded from 8.2.4 to 8.2.5.20 on each firewall. The Primary and Secondary work when they are standalone but, when we connect the fail over link from the Primary to the Secondary, invariably, one of them will go into a constant boot cycle and one will be active but, external users will be intermittently dropped. As soon as we unplug the fail over, the firewall that stays up behaves normally. This is with 8.2.5.20 code or any other code for that matter?
View 2 Replies View RelatedVPN tunnel between ASA 5520 ver 8.0(4) and a remote Juniper firewall keep tearing down during Phase 1 rekeying. After the rekeying process fails, manually pinging one of the remote hosts that are proteced behind the Juniper firewall,initates the tunnel renegoation and rebuilds the tunnel successfully.
Â
When the tunnel is down, sh crypto isakmp sa shows no active SA for the remote peer. That indicates the PHASE 1 negotation had indeed failed.When the tunnel is working, sh crypto isakmp sa indicates an IKE role of Responder - always.Clearly that also means Phase 1 negotation works only one way, i.e. negotation initated by the remote Juniper unit only.
 Â
Interestingly, the Syslog server logged the following SNMP trap messages at the time rekeying Phase1.Note, Line#2 and #7 and wrapped to the next line for easy of reading.
 Â
Line#1:Â Â IP = Remote-Peer-IP-#, Starting phase 1 rekey
Line#2:Â Â IP = Remote-Peer-IP-#, IKE Initiator: Rekeying Phase 1, Intf outside,
IKE Peer Remote-Peer-IP-# local Proxy Address N/A, remote Proxy Address N/A, Crypto map (N/A)
Line#3:Â Â IP = Remote-Peer-IP-#, constructing ISAKMP SA payload
[code]...
Â
As I understand from the above syslog trap, the Responder ( the ASA unit this time) started Phase 1 rekey (Line #1). It prepare a message to be sent to IKE Initiator, that it is about to start rekeying Phase 1 (Line #2). Down on the next line, it indicated that the local Proxy, remote Proxy and Crypto map as N/A ( not avaiable).Why would the ASA unit send N/A message as shown in Line#2, is that normal?
Internal network (LAN) works OK rock solid; only internet drops intermittently windows xp sp3 with latest updates wired connection
View 2 Replies View RelatedWe recently moved and upgraded our internet service from 1.5 Mbps to 4Mbps with CenturyLink. However, since our service was activated last Thursday, the internet connection intermittently drops and will not recover unless I reboot the modem. The period of up-time will last anywhere between fifteen seconds to several hours, usually falling along the five-to-ten minute range. No difference when using ethernet/wifi. The DSL light stays on, and the Internet light remains on as well.
View 11 Replies View RelatedI have a problem with a wireless adaptor on a Toshiba Tecra (A11-1EE - PTSE0E-065052EN) running Windows 7.The wireless adaptor works fine but every now and again it will just stop working. The operating system says that the adaptor is turned off but it isn't. I've checked the driver but it is up to date.I have to disable the driver and then enable it again and then the adaptor begins to work correctly again.
View 4 Replies View RelatedOk so my internet connection has recently started disconnecting and reconnecting every 5 mins or so. It has never done this before and has started doing it out of the blue. It doesn't even appear to have cut out by the icon at the bottom but it does stuff like stop youtube videos from loading or when I am playing online poker or online gaming it will cut out for about 30 seconds before reconnecting again.
View 14 Replies View RelatedMy internet connection seems to drop offline randomely while surfing the net. It basically results in yahoo or google freezing for 20-60 seconds before unfreezing and running flawlessly again. I seen a previous post that requested the individual hit start, run, cmd, and enter tracert google.com.
Windows 7 Professional
Service Pack 1
Intel® Core 2 Duo CPU E8400 @ 3.00GHz
[Code].....
The internet on my laptop only works intermittently. After a minute or so of initial use, it stops working and when I run the troubleshooter it discovers that the default gateway is not available, and then it says that it has fixed the problem. However, after only a minute or so more, the internet once again fails. I have tried the "run>cmd>enter>ipcongfig>enter" and found that the numbers for the default gateway are the same on my laptop as for a laptop that does work.
View 2 Replies View RelatedThe old 615 has been working very well for some years now, but the last couple of days we have had to turn it off and on again to get internet. It has happened 3 times in the last 24 hours. The globe light on the router remains green, and the notification icon on windows 7 doesn't show any problems yet we cant connect to the web. I've been looking on the forum and trying to understand some of the solutions and checklists already posted, but they don't make a whole load of sense to me unfortunately.
The firmware on the router is 2.27. The only change I have made to the system is that my wife's lan card seems to have died a death last week, and her computer is now connected by wireless. My computer is now the only one connected to the router by a lan cable.
There is something I don't understand. Under setup / network there is a dhcp reservations section. Pretty much every device seems to have a reserved IP address, and some of the devices that are reserved we no longer own. My son does gaming and wants a constant IP address, and my computer might need a permanent IP (don't know - just guessing here). Should all the other computers be allowed to sort themselves an IP every time they log on? Most of the devices have expires never, and some of the devices have the blue link that I can click for revoke and reserve with a time by them.
Am I barking up the wrong tree here and this lot has nothing to do with the dropping connection? What do the revoke / reserve and times mean? What happens when the lease runs out? Will the connection drop on that computer and it will have to try and connect itself again, or does it start a new lease every time it logs on to the router?
We're running Cisco Secure ACS V5.1 on a Linux platform to manage remote access to many networking devices. This has not been in place long, and is generally working OK. However, whenever I set the parameters of the user authentication to 'disable user account after X days if password was not changed', so as to comply with our internal security regulations, the user IDs seem to disable themselves intermittently, irrespective of whatever number of days I put in this - this can be a couple of days after re-enabling, or just a few minutes.
Â
This can be found in the advanced tab here: System Administration > Users > Authentication Settings.In the mean time, we are having to set the user authentication to be non-expiry. Is this a known fault with this version of software? If so, would there be a patch available, and how would I go about obtaining it?