Recently my computer has been unable to connect to a certain website. (cevo.com) I've deleted my cookies, tried different browsers, tried changing my MAC address, and still nothing. I've run several virus scans and tried connecting to the website on different computers in my home. It works on those computers. The website just won't load at all on my computer. Also, a program that must connect to the website to function properly won't work on my computer anymore either. I can connect to the website using a proxy site, but I still need to get this fixed.
When I ping cevo.com, this is what I get:
Pinging cevo.com [50.56.5.59] with 32 bytes of data:
Reply from 50.56.5.59: bytes=32 time=50ms TTL=46
Reply from 50.56.5.59: bytes=32 time=49ms TTL=46
[Code]....
Also, I plugged my computer directly into the modem and it still didn't work.
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access. Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I've spent 2 days already trying to get 2 ASA 5505's to connect using an IPSec vpn tunnel. I cannot seem to figure out what im doing wrong, im using 192.168.97.0 and 192.168.100.0 as my internal networks that i'm trying to connect over a directly connected link on the outside interfaces with 50.1.1.1 and 50.1.1.2 as the addresses (all /24). I also tried with and currently without NAT enabled. Here are the configs for both ASA's, the vpn config was done by the ASDM, however i have also tried the command line apporach with no success. I have followed various guides to the letter online, starting from an empty config and from factory default. I have also tried the 8.4 IOS. [code]
I have a problem trying to connect a VPN site to site between a FWASA 5515X - ASA5510. [code] The configuration in the 5510 its the old one that i been using with a firewall 5505.
After upgrading a couple of AS5505 to asa8.41 and using ASDM-641 I have been unable to set up a Site to Site using the Wizard.Had enough of a headache doing the upgrades on the CLI. I wait for my PO for Sec+ to clear so I can Add Failover. Ping was enabled and both '05 can ping each other. [Code] .....
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
We have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration... Current configuration : 5425 bytes ! ! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01 ! version 12.4 no service pad
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
1. i have 1 router with 2 computers.. i both checked their IP's using the whatismyip.com .. turned out they have both same IP.2. then i went to Download Angry Birds to download the demo version of angrybirds.3. my first computer could not download it, it says "unable to connect" , but my second computer can download perfectly..4. so now, i bought the angry birds game from rovio, i used my 1st computer to activate the game, guess what, activation cannot connect, so i cannot activate my game in 1st computer, but can activate in my 2nd computer.
I don't think this is specifically an internet explorer problem but i could not figure out which category it could have gone in. A few months ago random websites started becoming completely inaccessible to my internet connection, no matter how often i would try. The most recent one to have happened allowed me to connect just yesterday, but today i cannot connect to the website from this connection. I was able to connect to the website when i used the computer at a friend's house.
I have a cisco 7613 router and need to connect a site using Optical fibre (BSNL) on gigabit port,we will use convertor to convert optical signal to electrical .What configuration must be done on router to ensure this point to point fibre connectivity between my router and another router at differnt POp.
Everyone else sharing the same wifi connection as me has been having normal connection as always. My laptop does not connect to a single site because it always times out. If it does connect to a site, it takes like 10 mins. I got an alienware laptop.
Recently i bought Dlink 150 router and configure sucessfully for the Toshiba satellite laptop when i am trying to connect the status is showing as connected sucessfully but iam not able to access any URL with wirless And the same dilink router when i configure another laptop it is working fine so i a came to know there is problem with my Laptop
I can't open a connection to eca-msp.crashplan.com (which is one of the data servers for the CrashPlan backup service).Symptom: "telnet eca-msp.crashplan.com 443" hangs, and eventually times out.
Works fine when I connect directly to my cable modem.No PC or device behind my firewall can access it when going through firewall.Other crashplan hosts (notably, central.crashplan.com 443) work just fine.And of course, every other https site I use works just fine.
I have an @Remote appliance through Ricoh for our copiers. This appliance connects to their site to transfer meter readings and other information. This appliance can't connect to their site to transmit data. Ricoh is telling me the problem is on our firewill. I have assigned the Ricoh appliance a static IP address in our network. Our firewall is a Cisco ASA 5510. I don't have much expereince with logging on the ASA, so I'm not sure what "teardown dynamic TCP translation from inside" means. Is there something that is preventing this IP from contacting the Ricoh site? [code]
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
I have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
We've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
I've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
