Configuring An Internet Server And Client Cpu?
Feb 22, 2012
i have a new server but the ISP gave me this address
IP 41.221.92.150
S/Mask 255.255.255.252
Gateway 41.221.92.145
P/DNS 41.221.87.2
A/DNS 41.221.81.132
how should I configure my server and the client cpu?
View 1 Replies
ADVERTISEMENT
Jul 5, 2012
I use vmware workstation, and doing small networking project.i use 1 windows server 2008 x64 sp1 as DC, DNS and DHCP with 2 nic(1 nic for local(vmnet2) and 1 for internet(NAT)) and i use 1 windows 7 client machine.in server local nic settings are ip 200.200.200.1 sm 255.255.255.0 gw: empty dns 200.200.200.1
and internet nic settings all set automatic.and in DNS i added forwarder as my company's actual DNS server name.My requirement is client should browse internet by resolving through my dns server.but the problem is my server is having internet but my client windows 7 does not have internet
View 6 Replies
View Related
Jun 1, 2011
I have a small lan of around 10 computers in my office which are connected through a switch connected to a airtel broadband connection. I want to configure a network server so that I could manage an control the internet traffic used by all the workstations in the lan through that server. All the workstations have either WinXP or Windows 7 on it. I haven't purchased a server. I want to use a desktop(having some good configuration) as my network server.
View 6 Replies
View Related
Jul 11, 2011
Whenever my client browsing the net like youtube , facebook .y other client and the server encounter lagging .I Have : Router Dlink Dir600(4 Lan Port)Splitter Dlink Des 1016D (24 port x2)Pldt MyDsl ModemMy connection to server and client via internet .Modem - Router Dlink Dir600 RouterDlink Dir600 ( Port Lan 1) - Server Cpu .Router Dlink Dir600( Port Lan 4) - Dlink Des 1016D (24port)My Friend told me that it's better if i have Switch Over a hub connection Instead of Router And Splitter
View 2 Replies
View Related
Jul 18, 2011
My network connection was vanish the client are not connected to server and the computer cannot access internet
View 1 Replies
View Related
Feb 6, 2012
I was wondering if i should use the same RADIUS VSA attribute on ACS v5.1 to authenticate AAA clients as those i was using on my old ACS v3.3 server.
Example : under ACS v3.3 i was using RADIUS (Cisco Aironet) attribute to authenticate AP & WLC, should i do the same under ACS v5.1 ?
View 2 Replies
View Related
Jan 15, 2013
Need configuring Client to Site IP Sec VPN with Hairpin on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IP Sec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make traditional Hairpin model work in this scenario.
Following is the Running-Cong with Normal Client to Site IP Sec VPN configured with No internal Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel:
ASA Version 8.2(1)
!
hostname ciscoasa
[ code ].......
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
What needs to be done here, to hairpin all the traffic to internet coming from VPN Clients. That is I need clients connected via VPN tunnel, when connected to internet, should have their IP's Nattered against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16).
View 7 Replies
View Related
Mar 2, 2013
I have a problem configuring port forwarding to 443 and having client VPN to work.When 443 is NOT forwarded, VPN just runs fine (QuickVPN).As soon as I enable 443, the VPN stops working. No client can connect.I have the latest 1.2.0.9 firmware.Is there a way to enable 443 and having VPN to work at the same time ? I need 443 for Exchange.
View 4 Replies
View Related
May 15, 2013
I've struggled now for a couple of days to setup a PPPoe connection on our cisco 887va box. I can setup straight away on a draytek box so i know the connection is good.I can't get the line protocol to come up? It's connected via ethernet port 0 to an external modem. One thing i can't figure out is if ethernet 0 and fast ethernet 0 is the same physical port?I've attached the running-config below.
Building configuration...
Current configuration : 3738 bytes!! Last configuration change at 16:16:56 UTC Thu May 16 2013version 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname **!boot-start-markerboot-end-marker!!no logging bufferedno logging consoleenable secret *************
enable password ***********!no aaa new-modelmemory-size iomem 10!crypto pki trustpoint TP-self-signed-15463827enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-15463827revocation-check nonersakeypair TP-self-signed-15463827!!crypto pki certificate chain TP-self-signed-15463827certificate self-signed 01 **** quit!!!!!!ip cefno ipv6 cef!!license udi pid ***************!!username ************** privilege 15 password 0 *****************!!!!!controller VDSL 0operating mode vdsl2!csdb tcp synwait-time 30csdb tcp idle-time 3600csdb tcp finwait-time 5csdb tcp reassembly max-memory 1024csdb tcp reassembly max-queue-length 16csdb udp idle-time 30csdb icmp idle-time 10csdb session max-session 65535!!!!!!!!!interface Ethernet0description
[code]....
View 10 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
Jan 25, 2012
Does anyone have or know of a tried and true method of configuring a Windows Server 2008 box to provide authentication/accounting services for Cisco devices. I've read a few websites already and a lot of them seem to be geared toward VPN and some of the settings each site goes through are different.I've got NPS installed and a RADIUS client configured with the shared key. Right now I'm in the process of creating the Network Policy which only allows a Windows "admin" group to log in. Curious about the "Constraints" section where the NAS Port Type is selected and the "Settings" section where the service-type and vendor specific options are configured.
View 18 Replies
View Related
Jun 28, 2011
Configured a DP-G310 Print Server to work with the DIR 655? I have upgraded the firmware so I have WPA Security. I have typed in the WPA key in the DP-G310 setup. The DIR 655 sees the DP-G310 but it won't assign it an IP address. I can see the DP-G310 MAC address in the DIR 655 wireless status page but the IP is 0.0.0.0 and it disappears and reappears in the wireless connections list.
View 3 Replies
View Related
Feb 19, 2013
Im trying to configure remote access VPN on ASA5505. I configured it as local CA server, installed digital certificate on remote station and everything looks fine as far as i can see. I'm using cisco VPN client 5.0 on remote station. when i initiate VPN session it fails while trying to connect. Looks like im missing some configuration but i cannot figure out what it is. Currently i have firewall configured to use group authentication and everything works fine. I want to switch it to use certificate authentication, and if possible, confiure firewall to use main mode instead of aggressive mode for better security.
View 4 Replies
View Related
Apr 3, 2012
I would like to know the basic configurations for Win Server 2008 Standard for a small office (60 clients) The company has a Sales, HR, warehouse, and Accounting, and VPN for some sales, what configuration do you recommend me for each area? Right now my server has DHCP, DNS, and AD (do I need to install any other role?), Also what other configuration do I need in order to control my clients and users, and for security? how can I make the clients to save their files in my server? or make a copy of their files from their computers to my server? Any information for security? in my server or Router?
Like the tittle say, I just want to know all the configurations needed in a network for a small company.
View 1 Replies
View Related
Jan 12, 2011
How do configure win2008 server to bring up a password prompt box when access via a workgroup pc on lan.
View 1 Replies
View Related
Dec 3, 2012
We have recently installed Cisco for our wireless solution. We are an education and are looking to let staff and pupils bring their own devices. The route that we are planning to take to let them join the school's WiFi is to implement a RADIUS server so that they can authenticate with their Active Directory username and password. I have tried to test the solution but so far without any success. I am using a Windows Server 2008 R2 as my NPS server, I have setup the Cisco controller as per below:
Security Tab | RADIUS | Authentication - I added my windows server there and the preshared key, the Network User and Management is ticket and the server responds to a ping command,In the WLANs Tab, I selected my test WLAN and under Security | AAA Servers I selected the RADIUS server that I configured in the Security TabI then try to logon to my test WLAN and on the Cisco WLAN controller I get the following error: AAA Authentication Failure for UserName:test User Type: WLAN USER
Before trying to tinker with policies on the Windows Server I was wondering if the RADIUS is correctly setup on the Controller or have I missed something obvious?
View 6 Replies
View Related
Jul 9, 2012
I want to configure ad agent on windows server 2008 R2 SP1 with all need patch installed.When i try to connect to DC with adacfg dc list, status is UP. Log ADOBserver's don't show any errors. But when try to do command "adacfg cache list", result - empty. In what may be the problem? Perhaps it is related to the language of the OS?
View 4 Replies
View Related
Jun 10, 2012
I need configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.I have attempted to configure rdp access but it does not seem to be working for me. How to modify my current configuration to allow this? I need to allow the following IP addresses to have RDP access to my server: [code] The other server shows up as 99.89.69.334 but is working fine.
I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. My configuration file and what are the commands i need in order to put this through. Also, if there are any bad/conflicting entries. Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course.Also the bolded lines are the modifications I made but that arent working. [code]
View 8 Replies
View Related
Oct 23, 2012
Im trying to configure an ACE 4700 so that SSL termination is done on the ACE and HTTP reaches the weblogic server instance. I have a working setup of a Apache reverse proxy doing SSL offloading and using a weblogic module and that works fine Was reading [URL]. Any working config example for doing this with the ACE4700
View 2 Replies
View Related
Apr 5, 2013
Firmware 1.3 introduced a DHCP server.
It seems that I can add a pool for any subnet except the 192.168.1.1/24. I have successfully added a pool for 192.168.0.1/24, 172.16.16.1/24, etc. But when I use the same commands to add a 192.168.1.1/24 pool, I get:
sw(config)#ip dhcp pool network Device sw(config-dhcp)#address low 192.168.1.20 high 192.168.1.250 255.255.255.0 Illegal IP addresses range or subnet configuration Trying to configure a network pool on default IP interface
VLAN 1 IP was changed from default 192.168.1.254 to a static of 192.168.0.1.
View 2 Replies
View Related
Oct 8, 2012
Setup:
LAN (192.168.1.X, with .3 as gateway)
DMZ (192.168.2.X with .1 as gateway)
WAN (X.X.X.146 as primary public IP, .145 as gateway and .147-150 as additional public IPs)
I want to set it up so that X.146 is where all my outbound traffic appears to originate.I want tcp HTTPS and SMTP to be allowed from the WAN (via the X.147 IP) to a specific server (192.168.1.11) on the LAN.Also, HTTP traffic to X.148, X.149 and X.150 should go to DMZ and 192.168.2.8, 192.168.2.15 and 192.168.2.18 respectively, but I haven't added that to my config yet. Looking to get the HTTPS and SMTP ones working first, then I'll fix the others (one step at a time)I've got contact with the outside world when I've configured it using the ASDMs "Public Server" interface, but it refuses to properly establish the connection, I get a "SYN timeout".
My config:
: Saved
:
ASA Version 8.2(5)
!
hostname kcisco
enable password X encrypted
passwd X encrypted
names
[code]....
View 7 Replies
View Related
Apr 6, 2013
Currently running an ACE 4710, which is handling all of our inbound SSL connections and then forwarding requests thru to backend web servers. This all works fine.
My question is this..Right now we are not load balancing any of the backen web servers. But I now have a requirement that should a web server crash or become unavailable I need to redirect that backend connection to another web server.
Scenario is more like I have 2 web servers both serving same content, but I want one server to take all the connections unless it fails, at that point have all the connections forwarded to 2nd server.Is there a way to setup the load balancing where the 1st server gets all the connections until a failure happens ?
View 1 Replies
View Related
Apr 28, 2013
I would like to know if microsoft 2008 server RADIUS server could be use for authentication on Cosco 5508 instead of Cisco ACS.
View 4 Replies
View Related
Jun 3, 2013
We have a Cisco ASA 5505 at our CORP location, which I have configured the Site2Site VPN to our COLO with a Juniper SRX220h, the site to site works fine, but when users access the Cisco VPN client from home, they cant ping or SSH through the Site2Site. Contacted JTAC and they said its not on their end, so I tried to contact Cisco TAC, no support. So here I am today, after for the 3 days (including Friday last week) of searching the Internet for over 6hrs a day, and trying different examples of other users. The VPN client show the secured route to 10.1.0.0. [code]
View 19 Replies
View Related
Feb 13, 2012
I am having difficulty getting my HP Officejet Pro 8500(A910) configured to save digital faxes to my Iomega 2TB Home Media Sever (cloud edition). My home network is setup through a Linksys E4200.I was able to successfully configure it to save to a folder on my PC, but I do not want to leave it running 24/7.I believe the breakdown is in the Authentication part of the setup... It asks for the Windows username and password, which works fine for the PC setup but not for anywhere else. Do I use the UN & PW for the home media server if I'm saving to one of its folders? If so, how do I correctly type the path? It is communicating with the folder and leaving an alphanumeric file saved inside the folder when I use the 'save and test' option, but it breaks down from there.
View 1 Replies
View Related
Jun 5, 2013
I receive a question from a future customer about this future if its supported on " WS-C2960S-24PS-L":configuring 2 dhcp server on this swith ( 1 dhcp for voice vlan , and 1 for Data Vlan).I did some search , but i didnt find the answer .i have to advice a customer before ordering the switch.
View 2 Replies
View Related
May 7, 2012
I insert data from two clients.(1 window server 2003,2 XP clients ) the two client print paper and the printer is shared printer. At the same time two clients print paper and the printer stop working. So I restart my two clients and server. After restart the clients cannot ping to server.
View 1 Replies
View Related
Feb 28, 2011
I am trying to connect some thin clients to a domain based windows 2003 server. This the first time mi trying to do this. If the computer is set to workgroup there is no problem. The problem comes up when its a domain based server.I keep getting the message that the user is logged in. The host computer connecting to the server has the user name "thinclient" and I use the name "user" to log in from the thin client. But it says "thinclient" already in use and disconnect my connection between the host and the server.
View 2 Replies
View Related
Apr 9, 2012
I am installing Window Server 2008 with file Services, and I am making my clients to save files to their documents folder but those files are being saved straight in the Server. I was wondering if It is better to save files direct to the server or save files in each client?
View 2 Replies
View Related
Aug 23, 2011
A Windows Server 2008 r2 with 2 internet ports. One (IP: 10.0.96.132) connected to company intranet and one (192.168.10.1) as DHCP server connect to several PCs (192.168.10.**) through a switch.The problem is the PCs (192.168.10.**) can ping the DHCP server (192.168.10.1) , while DHCP server (192.168.10.1) can not ping (192.168.10.**).How to configure the server so that all these PCs can access the intranet?
View 4 Replies
View Related
Mar 8, 2011
how to change a clinet as server for all the remaining clients in a local area network
View 3 Replies
View Related
Sep 29, 2011
I'm having trouble connecting my client/server in my virtual PC. they just aren't seeing each other when it comes to connecting them to continue my server class.
server 2003 windows xp running on virtual PC I'm running windows 7 on my computer
View 4 Replies
View Related
Feb 9, 2011
I want make a workgoup network with my friend by VPN.we are connected throw internet to make the VPN connection.I configed a VPN server with incoming connection. client connected to server succesfully.but sever and client havent any data send or recieve. the server dont set an ip for client.this is connection propertice: as you see there is no data sending or dara recieving..Im using ADSL Modem(tp-link 8811) and have two lan networks with Modem and another computer.
View 1 Replies
View Related