Alright, the computer I had cisco connect on crashed. I got a new computer and I'm trying to install Cisco connect using the downloaded version and I can't install it because it requests the password of the router, which i do not know. This is because I've lost the CD copy of Cisco connect. I've tried resetting the router itself by pressing the red reset button
I cannot get my belkin n150 wireless router to connect to my laptop or ipad - wireless connection was working but stopped - so i attempted to re-configure the ip protocols on the router using the 184.108.40.206/ password - changed the ip setting on the belkin page but did not reset or set address (DHCP).
I've got a Belkin G wireless router.I've got my Vaio with windows 7 , my other emachines with vista and another acer laptop in the house also on vista/All laptops can connect to the router and internet fine but when I password protect the WI-FI the ACER aspire won't connect to the router, while the other 2 and also a ps3 all connect with the password no problems.
I had to unplug my belkin router and get a new modem from my cable company and lost the piece of paper that comes with the router when you buy it saying your name and ssid code. what can i do to get a new one?
I'm having issue with wireless connection on Belkin router F5D7633-4.Every 1-2 days my router disconnect and reconnect for no apparent reasons. When this happens, it affects it's wifi. All the devices in my house couldn't connect via wireless to this router. The only way to get these devices connected is to manually reboot the router.Do you know how to allow the router to allow many devices connected at same time?
I purchased a used WRT54G router that has DD-WRT firmware installed. I do not have the user name and password for it. How do I get around that issue so I can set the router up on my network. I would like to keep the DD-WRT firmware.
I have done all the resets, factory resets, hard resets, and any other names. When I attempt to enter any sort of IP addresses,default Belkins and ones I see when viewing ipconfig, all it does is perform a Google Search with the numbers.Again, turning on wireless on my laptop and phone fail to find my router, which used to just be called "Belkin".Here is all the info that I believe you need:
IP- Comcast Modem-Cisco DPC3008 Router - Belkin F5d7230-4 V1444 (althought a little old, have never had major issues untill a couple days ago)
Windows IP Configuration Host Name . . . . . . . . . . . . : JBerman-Win7 Primary Dns Suffix . . . . . . . : mmreibc.prv Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No
I upgraded my Mac OS to 10.7 (lion). I can no longer use Cisco Connect. I cannot recall the password I created when using Cisco Connect prior to upgrading to Lion. Is there any way to determine or reset my password without Cisco Connect. And why is it taking Cisco so long to provide firmware that works with Mac OS 10.7?
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
I haven't used my Linksys WRT54G v5 wireless router for about 1 1/2 years and needed it now at a new place.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and I've lost the disk for the control protocol program.I tried pressing the reset button to clear the modem and it took the WPA protocol off the modem so I can use it without any security but that's not a good thing.How do I get it freed up so I can get to the security protocols and put security back on my modem?
I can get on the internet and surf just fine but when i go to maps or Gas Buddie, or check in with Facebook it says" my device can not be located. Are location services turned on on the device." I have checked on my ipad and location services are on, on everything. I had no problem with the other router I had. I also have a Sprint Airave connected to my internet, but again i had no problem with the other router. The router is definitely faster than my old one and set up was easy but its very frustrating to not be able to find my location.
Does my Belkin F5D8236-4 ver. 1 (firmware 1.00.02) router support Apple's Bonjour print application. I can't get my iPhone or iPad to recognize my new HP Photosmart 7520 wireless printer which is connected to my network through my router.
I have had this same problem. When I clicked to connect on the wireless router with a new computer, instead of asking for the password (as most routers would) it asks for the PIN. The it takes me through to a strange page where it asks me to enter the name of the network and suggests the name of my computer as the name of the network. Once I chose a name it then connected locally buy not to the Internet and then disconnected my other computer from the Internet too. I tried thecomputerguy's suggestion but when I click on Wi-Fi Protected Set Up" it asks me for a password before I can access custom settings. It then won't accept the router password i had originally created, the pin or any of the other codes on the bottom of the router.It was weird-almost as if entering the router pin from my new computer overwrite the previous settings. The router has an installation cd which I didn't use when trying to connect the new computer-not sure if this has caused the problem?
I bought a N150 belkin router from a friend without the quick installation guide that was supposed to be incuded. I tried to set it up myself using the CD-Rom but wasn't able to so my roomate did it with the CD-rom she had. She didn't know how to put in a password so I was able to connect my laptop by pressing the WPS button on the router. Now I want to connect another laptop but I need the security key. How do I set one up?