I have a DIR-601 connected to cable modem. WiFi signal seems to drop randomly. I've been trawling through the logs and I see a lot of "UDHCPD Received a SIGUSR1" Is this related? what it means and how to stabilise the router?
Hardware Version: A1
Firmware Version: 1.02NA
Region: Canada
Wireless and wired connection.
[Code].....
I just replaced my older D-Link with a DIR-601. I decided to try the email feature, so I set the option to "On Log Full". Within an hour I had 5 emails. I noticed that they were mostly entries reading "DIR-601 local0.debug udhcpd[18594]: UDHCPD Received a SIGUSR1". The "Debug Information" option isn't checked.
View 1 Replies View RelatedToday i saw on the router dir-655 log file that "UDHCPD Received a SIGTERM" and "received signal 15, good-bye" and the ip address was renewd after 14 days. I want to understand if it's normal behavior of the unit or not. I'm connected to cable modem that is stable more than 15 days.
here is the log of my router:
Oct 23 17:49:48 debug UDHCPD sending ACK to 192.168.0.3
Oct 23 04:01:15 debug Debu: Joining group 224.0.0.252 upstream on IF address 46.117.1.47
Oct 23 04:01:15 debug Debu: Leaving group 224.0.0.252 upstream on IF address 46.117.1.47
Oct 23 03:59:09 debug Debu: Joining group 224.0.0.252 upstream on IF address 46.117.1.47
Oct 23 03:43:58 debug gpio create pidfile /var/run/gpio_wan_green.pid
[code]....
I receive wifi from an unsecured Linksys tower near by what can I buy to strengthen that signal will a wifi signal repeater work
View 1 Replies View RelatedHardware Version: C1
Firmware Version: 3.00
Wired works normally, and wireless is otherwise stable, except when under heavy load. E.g. if I initiate a large TimeMachine backup over wifi to my NAS, it will fail and the wifi will drop requiring a power cycle.I have tried a similar transfer over ethernet (~1.7Tb) and although the transfer speed wasn't great (~10MBs, likely due to NAS drive bottleneck), it completed without a problem.
If I try copying ~150Gb over wifi, however, it barely lasts 30 minutes without dropping out.Once the wifi drops, it still connects, but nothing works (I am unable to even connect to the web interface using the local IP). Other devices connected already via ethernet or 2.5Ghz still function normally, but the 5Ghz just fails, and if I try initiating a new connection to the 2.5Ghz it doesn't work until I power-cycle the router.As far as overheating goes, I'm not sure it is an environmental issue... I have the router standing upright in an open space so there is good airflow around it.
I'm having trouble with one of my DCS-930L cameras. I have successfully installed it and it's connected wirelessly to a Dovado router. However, after some 2 weeks the wireless connection drops and I can't connect to the camera anymore. As the camera is 350 km away I can't restart it. This happens everytime and the last time I was around the camera and indeed the camera LED was green. I restarted it by pulling the powercord and after that the camera worked for som 2-3 weeks and then the same problem again.I have 4 cameras, and it's always the same one that drops the connection and the router is only some 5 meters away from the camera. No walls between the router and the camera. I have the ability to restart the router with an sms, but that doesn't make the camera reconnect.
View 2 Replies View RelatedMy 655 router (RevB, Firmware 2.03) is connected from one side to a DSL modem and on the side to two wired PC's and via wi-fi to several other wireless clients (two smart phones and two notebooks). All is well until I try to connect a specific notebook. Connection is estabished for about 30sec and then the router drops ALL connections (including internet and local network!) and I must re-start him by un-plugging from power. This phenomena is specific to a specific notebook since with the other one
View 7 Replies View RelatedWe had our network set up using a Cisco wrt310n router and it was working greatThen suddenly we started having connection issues with anything wireless. There are 2 PS3's, 2 laptops, and 1 iPhone, 2 desktops but they are always plugged in and never skip a beat. When plugged in(where applicable) everything works just fine. So I changed the router to a D-Link wbr-2310. Network worked for a few days, but the wireless connection was a bit slow. Then it suddenly dropped wi-fi alltogether.
I updated drivers, updated firmware. And then the D-link stopped working even when wired, but thats a story for another time. So I plugged the Cisco back in, network up again. Worked for a few days and now I cannot connect wirelessly. I have my laptop in the same room as the router, it lists signal strength at full but says "did not receive any response from wireless router" and gives me a link to trouble shoot low signal... I have tried a lot of different tricks and settings and nothing has worked at all.
I have also noticed there are a lot of wireless networks in my area, I live in a townhouse complex. Each unit is seperated by a double garage, and backyard space. Last night I was detecting 11 networks. I tried using a different channel but no results.This isnt just an issue with one device, its every device I try and connect wirelessly, and with different routers.
I just bought a new router and i'm not able to access the internet on one of my laptops even though on the laptop it shows that its connected with full bars, it doesnt have this problem with the other routers i use. Also all my other computers are able to access the internet on this new router.
View 1 Replies View RelatedMy laptop is reading a full WiFi signal from my router. I am currently connected to the router via Ethernet on the same laptop. I've been reading tons of old threads to troubleshoot this. I'm at a loss. I have used this current networking hardware for more than a year without any problems. I do have a pretty old router but my iPod connects to the WiFi no problem at the moment. Here's what I've tried so far:
- soft reset of router
- power cycle modem and router
- removed saved network information from the laptop
[Code]......
I just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies View RelatedI have Virgin Media XXL broadband in the UK. I have Avast antivirus. Windows firewall is enabled and all security updates are up to date. I have a 50mbit virgin fiber optic broadband which is working fine on my flatmate's pc's. While making sure the internet wasn't being used my speedtest still returned around 1mbit with full signal strength. I have run speedtest on 3 pc's at the same time and 2 of them were over 30mbit while mine was still barely 1mbit. I am using an Edimax EW-7811Un nano usb adapter. From reviews I read that it should work great with Virgin. But for some reason it doesn't work well despite the full signal strength.
View 7 Replies View RelatedI am facing a kind of weird problem!! My Sony Vaio was getting connected to my Home wifi network and I could access Internet without any problem. Its been few days now that I can't access Internet though it shows connected. It does connect with the Wifi without any issue and even show the full signal like before, but actually there's no internet access. No browsers (IE,Chrome,FF) load any webpage, no messengers work.
View 1 Replies View RelatedI am using a Mac and would like to view the live feed full screen. Is this possible?
View 3 Replies View RelatedI have Asus EEPC Seashell/ 1015PEM netbook. The wi-fi connects only near/ so close to the wireless router with full signal. Just next room, blocked by a wall it disconnects, but full signal still exists. Is it anything to do with driver or hardware incompatibility- netbook has 802.11n adapter. Wireless router/DI624+ is 802.11g.
View 8 Replies View RelatedI am thinking of buying the DSC-942L, I already have "2" DSC-932L. I wanted to put it in my front door and set it up so it record to mine SD card 24x7. My questions are, when the SD card get full, does it overwrite the old files?
View 1 Replies View RelatedI set up an "access control" rule in my DIR-635 and so I have all navigation log from a PC of my LAN. But the URL in log are often truncated.There's a way to obtain a full track for an user navigation?
View 3 Replies View RelatedRegion : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet
How do I get the full 450 Mbps out of my router on the status it saying 300Mbps
This is on a DIR-655, firmware 2.01NA, hardware rev B1.Is there a limit on the number of DHCP reservations that can be added to this WAP?This WAP was working fine with 10 DHCP reservations (wired & wireless devices), 6 schedules, Access control of 2 devices by MAC (6 defined, only 2-3 active at a time).I started adding additional DHCP reservations, because I'm simplifiying my network, and when I add the 26th DHCP reservation I get the message "Schedule rules is Full! Please Delete an Entry."
I've been adding all of the new DHCP reservations as disabled, but I haven't assigned any schedules or otherwise to these new devices yet. So what's up with this message??
Region : Thailand
Model : TD-W8961ND
Hardware Version : V1
Firmware Version : 2.0.0 Build 111111 Rel.1111
ISP : 3bb
I have a problem when I am trying to add another static ip address to the list
the message above in title pop up, how can I fix it?
DHCP Table is Full!
I have tested internet speed on Ethernet (~20 Mbps), but when I'm connected via wifi network, it drops down to ~11 ? The speed is same on all wireless devices even when I sitting next to the wifi router.
View 8 Replies View RelatedJust three days ago, all of a sudden, my net drops off every 20secs like clockwork, only affecting the wireless.At the moment, my router is connected to the modem, and my computer upstairs is running through the wireless connection from the router (not the modem) - though it makes no difference the problem happens with either.
[code]...
I have a Windows XP machine which uses a USB wireless adapter. When I plug in another USB device, the wireless adapter drops the wifi connection.
View 1 Replies View RelatedI have a WiFi Linksys. I am using a Macbook Silver. This has begun recently, every few hours, the internet connection will drop. The only way I can get it back up is to unplug the wifi and plug it back.
View 6 Replies View RelatedMy net drops off every 20secs like clockwork, only affecting the wireless.I bought a new router yesterday to see if that would work, but it hasn't. At the moment, my router is connected to the modem, and my computer upstairs is running through the wireless connection from the router (not the modem)
My router is a NetGear N600 Wireless Dual Band... and my modem is a NetGear Rangemax wireless My computer is running Windows 7 and has a Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Network Adapter(im connecting to my network via the 2.4ghz... not the 5ghz)I've tried doing the whole, ipconfig/ release
I have used our home network with an apple iOS baby monitor app for a year without issues. An iPod is the transmitter and broadcasts the signal on my home network. Any other iOS device can pick up the signal when on "receiver" mode. This app worked great for over a year, but recently the app drops out after 1-3 hours. The dropped device also cannot get to the internet via Safari or communicate via the app. The WRT160Nv2 router indicates that the devices are still connected and the iOS devices indicate they are still connected, but they cannot communicate.
To fix the issue, I simply toggle the unit to/from airplane mode. This disables/enables the wifi and the unit jumps right back on the network and all is well. This is a pain though when the baby monitor drops in the middle of the night and we have to walk to the baby's room.
I have tried to recreate the issue with other video steaming (iphone video to appleTV), but I have not found the issue with any other app. Maybe I just have not run the movie long enough (3 hours+) like I do with the baby monitor app at night. Are there any wifi router timing or other settings that could cause something like this?
I continue to try to trouble shoot this:
1. wifi router issue
2. iOS issue
3. baby monitor app issue
I have a WRT310N V2 wireless router, with a WMP600N dual-band PCI card in my computer, using Vista 64x. I have had the same set-up for the past year or so, even after moving to a new apt, which I have been in now for 3 months. It has worked perfectly, up till recently. Over the past week however, my router has been dropping the connection, to the point of having to wait for it to show back up in my connections list. I made no changes to my setup, prior to the problems. I am kind of doubting it's my wireless card, as I can still see other routers. I have tried changing the MTU size, the Threshold, made sure the firmware was up to date, etc. I re-installed the drivers for my NIC and even changed ports, just to be on the safe side. I don't know what else to do, except go out and get another router. I have to use wireless, as I have nowhere to run cables at. I had this problem before with a Linksys wireless router, but figured it was due to the extreme amount of bandwidth my game uses online. Ironically, both routers are doing the same thing. They hit lag every 60 seconds almost on the money. I'm a gamer, so this is a huge inconvenience for me.
View 5 Replies View RelatedI've a WRV210 Wireless-G VPN Router with RangeBooster, that logs this alert almost every time, "Packet type : 0 -- free socket buffer only".Also each time that some devices, like Android, are connected to the Wifi, the wifi starts a reboot and drop cycle.
Some extra context information, I've connected to the router a Cisco Gigabit switch and all the wired devices are connected to the switch, that could overload the router? Other point I've a Cisco VOIP gateway connected to the router and a few VPN's and firewall rules setup.
My computer is a Toshiba Sattelite o/s win 7. My wi fi signal is excellent, yet my signal keeps dropping or saying limited access.I have tried resetting the router and resetting my default windows settings on the computer. All other lap tops and wireless devices in the house do not have an issue.I discovered the other day as long as the laptop ( not the router) is plugged in and not running on batter power that i do not have a problem staying connected.For fun i wondered if it had something to do with the power cord making some kind of connection when plugged into the lap top, (since everything is more compact in them)I tried having the power cord plugged into the lap top but not into a power source but I still lost signal.
View 1 Replies View RelatedThis is another E3000 "connection drops" thread. Some background: I have two E3000's that are cascaded. The main router is in my basement connected to my cable modem and is my DHCP server. The second one is on the main floor and provides my wireless signal (no DHCP, and is hard connected to the main router).I have lots of connection drops with the wireless router on the main floor. Lately I have noticed a trend, though. My connection drops mostly when I browse my network (usually browsing pictures on another computer) or when large files or videos are being transferred. If I connect a cable, I have no problems. When wireless, I have signal drops.I have tried every trick and tip that I've seen on this forum or been provided in the Linksys FAQ. I've changed the beacon interval, fragmentation threshold to 2306 and CTS to 2307, I've tried changing channels, I've checked and unchecked boxes for NAT, Filters, etc. I've tried different combinations of WPA2 passwords. I've tried dynamic routing, static routing, blah blah blah...
When I set the 5Ghz channel to Auto(DFS) it defaults to channel 36 and 144Mbps. When I use other channels, I get 300Mbps. Either way, my connections still drops.
I have the latest firmware 1.0.04 Build 6.I even have the router sitting on top of a laptop cooling pad to keep it cool.No matter what I do, as soon as I start browsing my network the wireless connection drops.I am so frustrated! I upgraded my WRT-160N to this E-300 router to get the faster speed and dual band but have had nothing but trouble. I never had a connection drop with my 160N.
EDIT: I notice that when my signal drops, I can see the power LED blinking on the router, like it's going through a reboot cycle.
I own a CISCO Linksys 3500 router I use in my home. Every time there is a power outage, the router stops working. The only way I have managed to get it to restart is to remove the software, disconnect the router and then re installed and set up the router again
View 1 Replies View RelatedRouter: E1200 2.0.02 build 3 Feb 15, 2012
These symptoms are stumping me:
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
I've been experiencing a strange, repeatable behavior with my Linksys E1000. I have several wireless and wired devices connected to my E1000:
Wired: TivoHD, Sony BluRay Player, Sony TV, Windows XP Wireless: Lenovo Laptop (Windows 7), HP Laptop (Windows 7), 3 iPods, 2 iPhones
When I try to copy large files (~ 4GB) from my (wired) Windows XP box to either of my (wireless) laptops, the Linksys drops my WiFi network -- but the wired connections continue to work (including internet access). Copying the same/similar file from a WiFi device to a wired device appears to work correctly, as does copying from WiFi to WiFi.
To be clear, my WiFi network "disappears" -- it is no longer listed as an available network (as opposed to just dropping internet connectivity for WiFi). Unplugging the router and plugging it back in brings my WiFi network back up.
I have been able to repeat this issue with multiple files over the course of several weeks, and it happens about 75% of the time (i.e., I am occassionally able to complete a file copy from wired LAN to WiFi).
A little bit of background: I resurrected an old Windows XP box and am using it for shared network storage. I copied about 400 GB of files from my laptops to the XP box (WiFi to wired) with no issues at all. Pulling the same files back from XP to my laptops (wired to WiFi) has been causing the issue described above.