My parents recently purchased a Linksys N600 router to satisfy their wifi needs. They are running into an issue. Apparently, only my mothers laptop is able to fully connect to the device and port data in and out. My fathers laptop and his tablet both are unable to get past the "limited connectivity" yeild. They are both running on laptops using Vista and the tablet is Android.
View 1 RepliesI have problem connecting the wifi router to my desktop (running Windows XP) through LAN. When i connect the internet cable directly to my desktop, it was working. But when i connect the internet cable to wifi router, then a LAN cable from router to desktop, my desktop is showing that the network cable was disconnected. I have used the different lan cable too. I have used the reset function too. But the problem was not solved. I am getting the wifi access. But the connection between the router and the desktop was not established.
View 1 Replies View RelatedI recently purchased a WRT120n router to set up wifi in my house. I had installed the software and had the Wifi up and running. However, I am unable to connect to my wifi connection thru my cell phones. It does not connect to any of the smart-phones we have at home (Nexus S, iPhone 3G, )
The wifi connection is working on the laptops (Mac and Windows). Just not connecting to the phones.
I have a Cisco Linksys Router Model WRT120N - which is connect wirelessly to my MAC home computer. I also have a Dell D630 Laptop using WindowsXP. I have recently moved and my laptop used to connect to my wireless router (when I was at my old house) But now at my new house my laptop wont connect. It will connect wirelessly at other locations. The laptop picks up the wireless name and shows full strength.
View 1 Replies View RelatedThe internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies View RelatedI just installed a band new copy of xp on my system and I cannot connect to the internet! I'm connected via Ethernet to my Belkin n600 HD and whenever I go try to follow the steps via Microsoft [Go into Network Connections > Create a New Connection > Connect to the Internet > Set up my connection manually > Connect using a broadband connection that requires a user name and password] It just brings up the old school dial up vpn style thing and never connects to the net. Secondly I tried to install the Belkin software but it just has errors trying to establish a connection with it. The Internet is working fine, I have 5 laptops connected to it.
View 3 Replies View RelatedI have a N600 router. Yesterday, for the first time, I was unable to connect to the internet from my TV. It keeps saying network connection failed. I have unplugged the router and modem several times and that does not work. When I check the various wireless systems available (on the TV screen) I see mine there but it will not connect. At one point I did see something that said ethernet cable disconnected, but I checked and the cable is connected.
View 4 Replies View RelatedI am trying to install a Belkin N600 to a Windows 7 desktop with no luck. When I run the setup off the install disk it attempts to install the driver needed for the N600, but every time it fails the install stating that the device is not functioning. When I connect the N600 to my computer it sees the device but its almost like my usb ports are not powering the device even tho I have connected a lash drive to all of my ports to make sure they were working, and they are( All usb ports are 2.0).
View 2 Replies View Relatedabout two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies View RelatedMy net drops off every 20secs like clockwork, only affecting the wireless.I bought a new router yesterday to see if that would work, but it hasn't. At the moment, my router is connected to the modem, and my computer upstairs is running through the wireless connection from the router (not the modem)
My router is a NetGear N600 Wireless Dual Band... and my modem is a NetGear Rangemax wireless My computer is running Windows 7 and has a Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Network Adapter(im connecting to my network via the 2.4ghz... not the 5ghz)I've tried doing the whole, ipconfig/ release
I cannot connect to the WiFi router, an all-in-one modem+router provided by my ISP. Now, I run an Ethernet cord from the router to my computer: the computer works just fine. As of a day ago, though, none of the home's Apple devices will connect to the network, despite reboots, password retypes, and shouting at them. Each device (two phones and an ipad) can identify my network, but they cannot join. Additionally, there is an old laptop that cannot connect anymore.
View 7 Replies View RelatedI just successfully setup my wireless Netgear router to work with my laptop and desktop. I now want to get my iPhone to connect to it as a WiFi connection. It sees the available network after I enable WiFi, but when it tries to connect, it just says "unable to connect" or something after I input the password.
My current password shows in the Netgear router (through 192.168.1.1) in the "passphrase" field under Wireless Settings, and it's cp6s-n3rb-ziav. This is what I put in the password field for my particular network in the iPhone before it tells me it can't connect.
There is an option on the left column in the router for "Set password," but it's just to change it to something else. If my iPhone won't accept the current one, I don't see why it would accept a new one, and then I'd have to go and change it in the laptop, too. Without knowing if that's the issue, I'm holding off on that for right now.
I have been using broadband in my laptop using asus wireless router/modem DSL-N10E for last 2 months but with Ethernet cable plugged in. I have never used its wifi function. I tried today but was unable to connect after entering security passwordWhen look for troubleshoot it says "There might be problem with the drivers for the wireless network connection adapters"
View 4 Replies View RelatedI recently put in a Netgear firewall, configured it, its running no problem. Then I setup a new Netgear N600 wireless router, configured it, gave it a static IP, connected to it, works like a charm. Thing is, when I try to access the web gui I receive nothing.. Is the Netgear firewall taking priority or something? I went directly connected to the netgear wifi router and double checked to make sure that there was no settings restricting administration from wifi users, etc..
View 3 Replies View RelatedI own an AG214 ADSL2 router that I use for my desktop PC. I now however also have a WRT54GL for wireless connection. I connected the WRT54GL to my AG214 via ethernet. Everything works fine, I have wifi and I can use it to connect to the internet. However when I go to my router (192.168.x.x) I can't seem to be able to find a wireless tab to configure my wifi settings. The network right now is unsecure and has a default name (linksys). How do I access my wireless settings? When I access my router it does go to the AG214, do I need to access the WRT54GL? If so, how do I do that?
View 4 Replies View RelatedI've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
I've got a new E4200 router, Everything works just fine, but I'm unable to ping any WiFi hosts from my LAN, I can ping LAN from any WiFi Host.If I disable NAT on the E4200 I'm able to ping WiFi hosts but then all WiFi Hosts are unable to talk to the LAN.
LAN - 192.9.209.0
WiFi - 172.16.1.0
Same config runs perfect on my WRTG54GL.
Set up a Smart Wi-Fi yesterday. Linksys Smart Wi-Fi Router N600. Have 2 computers side by side. Connected my computer seamlessly. Works perfect. Went to set up my husbands computer (both computer are desk top HP Pavillion running windows 7) and the way I was doing it thru the network sharing center on his computer I was not able to get the computer to see the wi-fi. I tried both the router p/w and the p/w that was supplied by the smart wi-fi help center. So I wired it directly to the Linksys router with a new cat-5 ethernet cable. VOILA..internet connection! Question..is his computer secure even tho it doesn't have it's own p/w and is wired directly to the router? My thought is "yes" since the router is p/w protected.
View 8 Replies View RelatedTrying to get my Netgear N600 router to connect to the internet...nothing will get it to connect.I am able to follow step-by-steps to resolve this
View 14 Replies View RelatedI puchased the N600 WNDR3700v3 Dual Band Gigabit Router. I am able to see my wireless account I set up and is out there to connect to, but I cant connect. I can connect with an ethernet cord, but nothing wireless. It doesnt work for my home or work laptops. Prior to this I had another wireless set up and I am tempted to plug that one back in.
View 1 Replies View RelatedI have cable broadband internet.My internet modem is a Ubee D3.0.It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via Ethernet.My wifi went down the other day.Devices were connected, but were not getting any internet service.In troubleshooting, I attempted to dial in to the router using url... as well as 192.168.0.1, and I could not get into the router.I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one.I got home and plugged it in, still not working.I can't access it using the above mentioned methods, and the setup software does not detect a router present.I unplugged the router and hooked the computer up directly to the internet modem.Still no luck.The computer does show a network connection in the system tray, but with no internet.I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. even did a system restore to a restore point last week when I know the internet was working..
View 5 Replies View RelatedJust bought a new Netgear N600 router, hooked up 4 wired computers with no problem and got several wireless devices to hook up without issue. My laptop however, will not give me internet access when accessing the network wirelessly.
The access is labeled as Local Only, and the network is considered unidentified. Signal strength is excellent, and it reads the name of the new wireless server I created. It prompted me to enter the passphrase, which I did, and now my laptop is stuck on local only.
I tried updating my adaptor drivers but they are all up to date, and I tried to enter my adaptor into the address reservation on the router configuration page using the laptops MAC address and IP address.
I am unable to get this to hook up my vizio dvd player to wifi
View 2 Replies View RelatedMy son just got an Asus Laptop from his school. It is running Windows 8.It connects to other peoples WIFI, just not my home WIFI.When he got it home he found the network, entered the password and nothing happened. Now it can't even find the network.There is nothing wrong with the router as every other device connects fine.The router is a Netgear n600 - DGND3700?
View 3 Replies View RelatedI have internet through my cable company and currently use their wireless netgear router. I purchased a Netgear Router N600 but it does not have a port for the cable connection. Can you recommend the correct wireless router
View 1 Replies View RelatedIn my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
I have cable broadband internet. My internet modem is a Ubee D3.0. It is connected to my Netgear N600 Wifi router which have my computer and DirecTV hooked up to it via ethernet. My wifi went down the other day. Devices were connected, but were not getting any internet service. In troubleshooting, I attempted to dial in to the router using www.routerlogin.net as well as 192.168.0.1, and I could not get into the router. I assumed the router must have crashed, and I only purchased it a month ago, so I took it back to the store and exchanged it for a new one. I got home and plugged it in, still not working. I can't access it using the above mentioned methods, and the setup software does not detect a router present. I unplugged the router and hooked the computer up directly to the internet modem. Still no luck. The computer does show a network connection in the system tray, but with no internet. I plugged my laptop in to the internet modem, and I am able to get internet just fine from my laptop. I even did a system restore to a restore point last week when I know the internet was working. No luck.
View 5 Replies View RelatedI have a actiontec Wireless N ADSL Modem/Router Model# GT784WN & netgear n600 wndr3400v2 router that I would like to setup as a Wireless Repeater. I can not seem to get the netgear n600 setup.
View 1 Replies View RelatedSo I have a Netgear N600 WNDR3700 wireless router setup at home, and it works great for wireless, but when I plug in my desktop with CAT6 Ethernet cable to the router (didn't bother putting a wifi card in my desktop) for some reason it won't connect to the internet. I know the cable works because I've used it in the past, but for some reason I can't get it to work with my Netgear router.
View 7 Replies View RelatedI can not connect any equipment by WIFI. Tablet & Ipod. Equipment recognize a network but doesn,t connect.
View 1 Replies View Relatedlaptop to the Internet via wifi and am having no luck. The other computers in the house and my iPhone have no issues connecting, but his computer does for some reason.When I look at the status of the wireless connection, it's says the the IPv6 is limited.Since I am posting this from my iPhone, I'm limited as to what information
View 6 Replies View RelatedI've been unable to connect to the internet or even my Linksys router (192.168.1.1) from my main desktop. However, I can access the internet and the router by way of another (older) desktop and two laptops.This problem occurred after powering down and unplugging both desktops before a thunder storm. Later that night I powered on and had this issue. ISP didn't have any outages in the area. [code] Network and Sharing Center displays (this computer) with a line connecting to Unidentified Network and the red x between Internet. When viewing the status of that local network connection packets are being sent but 0 are received. TCP/IPv4 and 6 Properties are set to obtain IP/DNS automatically.I don't have any additional firewall software but windows firewall is enabled.
View 10 Replies View RelatedI've got a dell n4110 windows 7.
For whatever reason I can't connect to public wifi (school, library, cafe, etc) but I am able to connect to my home wifi no problem.
I can see it, just can't connect (doesn't give an error message, just says unable to connect).