Linksys Wrt54g - How To Access Router Set Up Page

Oct 8, 2011

running linksys wrt54g wireless router to two towers and 1 laptop----had short power outage after which i lost connection to router only on one tower---other tower and laptop were unaffected----had green indicator lights for positions 1 and 2 hard wire connected towers before outage---now only position 2----looking for reasons why I lost number 1 and thus connectivity to the router----have tried powering down router etc---but have not reset it---looking for more info first

View 1 Replies


ADVERTISEMENT

Linksys WRT54G V3.1 - Cannot Access Set Up Page In Router

Sep 18, 2011

My wifi router, Linksys WRT54G v3.1 has been working fine till now. Suddenly my laptop stopped receiving wifi signal. I am unable to access the set up page via 192.168.1.1 either from my laptop or from my desktop that is connected to the modem via the router. I reset the router as well but no luck.

View 5 Replies View Related

Linksys Wireless Router :: Cannot Access WRT54G Setup Page

Jan 19, 2013

I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G - How To Access Setup Page

Apr 27, 2012

When I had DSL, my WRT54G was my DHCP master for my home network.  When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point.  But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again.  I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want.  The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
 
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server.  Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G.  This solved my problem:  my distant wi-fi computer now has a good signal, and both computers "see" each other.
 
However, now I seem to have lost access to the WRT54G setup "web page."  Is it possible to access the innards of the WRT54G when its DHCP service is disabled?  Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

View 3 Replies View Related

Access Linksys WRT54G Config Page?

Dec 24, 2012

I just got a new Sharp Aquos Television and I wanted to try to find the SSID so that I could pick up a connection with my TV. When I went to command prompt and typed ipconfig to get the default gateway, the gateway ip took me to what appears to be my modem's config page and not the Linksys. how I can get to my WRT54G config page.

View 2 Replies View Related

Linksys WRT54G - Garbled Router Web Administration Page

Mar 11, 2013

Sometimes, when I access my router's (Linksys WRT54G) web administration page, it comes out garbled; i.e. missing text, icons, links, form controls, etc.

Gets fixed after powering the router off then on again.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Administrator Page Is Broken?

Sep 27, 2012

I recently "uninstalled" DD-WRT from my router and tried to install the actual firmware for the router, so I went to this page [URL] WRT54G and select version 5. My router is really version 5.1 but I read on this forum that this router works with version 5 so I downloaded it and installed it.
 
However, this is how my admin page looks like,
 
And I can't do anything at all. Is there a fix for this? Is there an actual version 5.1 firmware? Or must I switch to a different, proper router?

View 8 Replies View Related

Linksys Wireless Router :: WRT54G Page Has Reverted To Default

Feb 24, 2012

I have a Linxsys WRT54G.  Once every week or two, it seems to "forget" its name, and revert to the default name.  When I try to access it with my laptop or phone, "Multivac" is gone, and "Linxsys_XXXXXXX" (where XXXX are random numbers and letters) has taken its place.  When I go to the setup at 192.168.1.1, the "Router Name" on the first "Basic Setup" page is still "Multivac," but the "Network Name" on the second "Wireless" page has reverted to the default.  If I change it back to Multivac, everything is fine for a week or three until it "forgets" again.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Put ASPX Page When Start Connection?

Sep 9, 2011

Is there a way to put the .EXE program in the start connection in Wireless Router WRT54G ?
 
or a .ASPX page when start the connection ? I want to do it:
 
I want to control the time that the users used the internet in the hotel. The users had the login and the password which one. And I want stop the connection when the user get the time.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Lost Username And Password For Admin Page

Apr 30, 2007

I seem to have lost my username and password for the admin page for my WRT54G router.Is there a way to retrieve or reset the login?

View 9 Replies View Related

Linksys Wireless Router :: WRT54G V8 / Unable To Navigate The Basic Setup Page

Jan 14, 2008

I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed."  I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it. 

View 9 Replies View Related

Linksys Won't Allow Access To Router Page

Apr 17, 2011

I have a linksys router, Its at my sisters house. her son is trying to hook up his Xbox to it. The router will not allow me to access the router page, ( I called them and walked them through it). I reset the linksys router, by holding the reset button in for 45 seconds. Then I access the router page by going to 192.268.1.1 Windows gives me a popup to log in, What I find on the internet for a default login is the user name is blank and the password is admin. OR the both the user name and password is admin. However it still will not let me into the router page.

I am wondering if the login popup is something with the windows settings. As when I had the router here at my house, I think It just went to the webpage of the router and thats where it asked me for the user name and password. I do not recall the popup login window before the router page. Is there something to turn off to set it so that windows does not give a popup to login and goes to the webpage to login?

View 9 Replies View Related

Cannot Access Router WRT54GX Web Page / Setup Page?

Jul 28, 2011

i need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen

View 2 Replies View Related

Linksys Wireless Router :: Way To Access Set Up Page For Secondary WRT300N

Aug 13, 2012

Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
 
Is there a way to access the set up page for the  secondary WRT300N, bypassing the main router intervention via the Cloud  software?

View 3 Replies View Related

Linksys Wireless Router :: Can't Access WRT160n Setup Page

Oct 16, 2012

I have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.

View 5 Replies View Related

Linksys Wireless Router :: Cannot Access E1200 Setup Page

Nov 29, 2012

I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....

View 6 Replies View Related

Linksys Wireless Router :: Can't Access Setup Page WRT54GS

Sep 9, 2012

I need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding.  I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing.  The connection times out.  I really need to protect my network.

View 1 Replies View Related

Linksys Wireless Router :: 1721 - Can't Access Setup Page

Jul 11, 2012

My internet is T1 by Verizon. My mom's company Siemens pays for our internet because she works from home as medical tech support on the phone. Okay so the T1 had to be laid out to our house underground I think because where we live, other brands of internet aren't available. The T1 goes from the box outside into our basement and hooks up to a Cisco 1721 modem. From the 1721 the internet goes out to a wireless router that is sitting right next to it. This wireless router is a Linksys WRT160N V2. We have several cables coming out of the WRT160N V2 to go to the first floor for hardwired connections, but one cable goes to the attic and connects to a second wireless router. The second wireless router is a Linksys E2000. We have several cables coming out of the E2000 that go to the 2nd floor to serve as hardwired connections.Okay so let me explain where things went wrong.

After a storm our power went out. Eventually the power came back on, but every now and then our internet would shut off for like half a day then turn right back on, so our internet was getting really really spotty. The [b]AL[/b] light on the Cisco 1721 would come on every time the internet went out. It was so bad that my mom had to get an aircard from verizon to get internet. So after two weeks of spotty service and arguing with verizon trying to get them to come fix the problem, they said try resetting your wireless routers because they might have "bad data" in the lines causing spotty connection. So we reset the wireless routers by holding down the reset buttons on the back. Well.. this reset all of the settings for the routers which Cisco facilitated set up, and now our wireless routers are out of warranty date so they can't set the wireless routers back up. However, we have copies of the online wireless router set up page, so we thought maybe we could just set them up ourselves.Well the problem is... We don't know how to connect to the wireless setup pages.. I read something on the internet about setting up wireless networks and to type 192.168.1.1 into our browser(Mozilla Firefox) and that would bring us to the wireless setup page. But the page does NOT ever come up.

Another way to find the IP address of our wireless routers would be to try going to the cmd and typing in ipconfig and using the Default Gateway IP address for the browser to connect to the setup page but that doesn't work out either.... Right now I unhooked the Linksys WRT160N V2 and hardlined the Cisco 1721 to the Linksys E2000 to a PC on the second floor because I figured it wouldn't work out if we had two wireless routers running at the same time. Currently the browser is taking me no where at all. It just says "Connecting..." but nothing is loading up at all.I tried hardlining from the Cisco 1721 to my mom's laptop, which is her work computer, and I got no response at all. I figured it might just be her work computer that was messing up and not allowing her to hardline into the 1721 so I tried hardlining the Cisco 1721 straight to the PC desktop on the second floor(we have no other laptops other than my mom's work laptop) and nothing went through. Then my dad says the Cisco 1721 has been configured so it doesn't direct connect, meaning that it has to go through a wireless router.

View 4 Replies View Related

Linksys Wireless Router :: E1200 - How To Access Router Admin Page

Apr 1, 2012

I want access the my E1200 website in order to implement new username and password to secure the network.

View 1 Replies View Related

Linksys Wireless Router :: Need Access E1000's Web-based Setup Page

Jan 6, 2012

I have a Linksys E1000 wireless router, and I seem to have either written down the password incorrectly or am using the wrong one. Regardless, I can not access the web-based setup for the router. Is there anyway to reset the username and password for it?

View 3 Replies View Related

Linksys Wireless Router :: WRT310Nv2 Sometimes Blocking Access To Facebook Page

Nov 6, 2012

I've been using my WRT310Nv2 Cisco wireless Gigabit N router for 2 weeks now, and sometimes, it's blocking access to Facebook.comI am not aware if it does the same thing with other websites, but my guess is that if I fix this one, I'll fix them all. So here I go, I click on my Facebook icon in my bookmarks and all goes well. Then, a while after, Facebook doesn't respond anymore and I'm send to a page that says "this is probably not the webpage you are looking for!" and it goes on about someone probably trying to hack my Internet and so on. But it's impossible: my network is under a solid WPA/WPA 2 security access. So I try again and click on the FB icon, and it shows me this:

"Invalid URL
The requested URL "/", is invalid.
Reference #9.c2c28f18.1352263449.304a8c9"

View 9 Replies View Related

Linksys Wireless Router :: Wrt120n Unable To Access Settings Page

Jan 6, 2012

Have a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".

View 2 Replies View Related

Linksys Wireless Router :: Wrt54g2 - No Access Through Wifi To Setup Page?

Jul 16, 2011

I bought wrt54g2 several years ago and everything worked fine until this week. I got trouble with this router now.All the computers at my home couldn't access to this router even just connect to router's setup page at 192.168.1.1. The only way go to setup page through LAN Cable .I'm afraid maybe there's interference channel with my neighbor, then I did some change to router channel already, but the result same. I still couldn't access to the router through WIFI
 
Fyi, I did upgrade the firmware with the latest one and all the computers distance to the router not more then 5 m and in the clear area

View 6 Replies View Related

Linksys Wired Router :: BEFSR41 Lost Access To The Admin Page

Nov 13, 2007

I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.

View 9 Replies View Related

Linksys Wireless Router :: WRT610N No Access To Edit Any Settings On The QOS Page

Mar 11, 2012

I entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);

Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.

View 1 Replies View Related

Linksys Wireless Router :: Unable To Access Cisco Admin Page For 54G V5

May 3, 2012

I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5.  Also need to connect VPN but unable to. 

View 1 Replies View Related

Linksys Wireless Router :: Can't Access Cable Modem Status Page With EA6500

Apr 5, 2013

I cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?

View 9 Replies View Related

Linksys Wireless Router :: E900 - Upgraded Firmware / Changed IP Now Cannot Access Setup Page

Jun 6, 2012

I bought E900, accessed setup thru 192.168.1.1, upgraded its firmware.. then changed router's IP, it reboots, then went blank, I cannot access the setup page anymore?

View 9 Replies View Related

Wrt54g Linksys - Cannot Access Router Settings

Jan 1, 2012

I have a wrt54g Linksys router, and recently whenever I type 192.168.1.1 into the internet in order to access the settings/homepage, I get " internet cannot display this webpage"

View 2 Replies View Related

Linksys Wireless Router :: E3200 - Block Keywords And Customize Default Page Given When Access Restricted?

Aug 5, 2012

Is there a way to block keywords and also customize the default page given when access is restricted?

View 1 Replies View Related

Linksys WRT54G - Router Connected But No Internet Access?

Dec 27, 2011

So, I restarted my linksys router (WRT54G model) yesterday because of some issues I was having. Right now, I have full bars for connectivity on all my devices (Acer Aspire laptop running Windows 7 starter) when the Ethernet cord is connected from the modem to the router, but I have no internet access. Only when my laptop is connected directly to the modem, I have access to the internet (but ofcourse no wireless).

View 1 Replies View Related

Linksys Wireless Router :: WRT54G V8.2 Cannot Access Setup

Apr 13, 2012

I had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:

Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.

View 5 Replies View Related

Linksys Wireless Router :: WRT54G Can't Access Own Sites

Nov 14, 2011

My own sites were down & I can't view them on my computer now.This is the 2nd time this has happened to me with router WRT54G.Every time there's a problem with my hosting company & my sites go down, my router blocks them once the sites are back up & running.When I plug directly into the modem I can access them, but then I can't use my phone, etc.I've recycled & I keep trying to find how you save your settings on your router so I can do a cold reboot, but I can't find the instructions anywhere.Why does it keep doing this & how to save the settings & restore them.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved