Split TS And Main Server - Separate Broadband Line?
Aug 29, 2011
1.I want to have a seperate Broadband line for a Server running TS for certain users to log into to.
2. I want another broadband line that is split via switch for other users and servers.
Reason: Speed up connection for TS users so that are on a dedicated line.
How will I get TS Server to speak with my Main File server to access the files they need and there is 1 folder both networks should have access to?
TS server and Main server in Same building. Don't want to use a WAN routers to connect the 2 routers together. My Broadband (According to speedtest.net = 12Mbps DL/ 0.80Mbps UL)
View 2 Replies
ADVERTISEMENT
Jan 23, 2011
I have two networks with two different external IP address, of course I have two routers where separate PCs are connected.
My question is if is possible to run with the adapter like DHP-342 or DHP 200 this two LANs over power without conflict?
View 1 Replies
View Related
Mar 26, 2011
i have two broadband line in a lan. it is physically connected to same switch then same switch to connected other computers.now, i want to when one broadband line down or disconnected in the mean time another broadband line automatically backup internet line. so i want to free software for this reason to get these solution.
View 1 Replies
View Related
Apr 11, 2011
In a house that is too large for a small wireless modem to send a signal far enough, is it possible to use a second modem in the same phone line (not at the same time). Filters are used in the spare phone jacks.My main question is: when modem A is being used and modem B is switched off, is it necessary for the splitter for modem B to be removed and the filter put in its place? Or is the fact that modem B is switched off sufficient? I suspect that it's necessary and that's why my friend gets very slow download speeds even when the other modem is off.She insists that it used to work but I think she was just lucky if it used to work.
View 2 Replies
View Related
Feb 19, 2011
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies
View Related
Aug 16, 2012
I have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
View 1 Replies
View Related
Nov 20, 2011
I have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
View 6 Replies
View Related
Dec 26, 2011
I can not get onto the internet via dial up. The message says that I have no dial tone. Using the same line, I get a dial tone on the phone. I can get onto the internet via a DSL connection, but it will not make a connection when I have a telehone line inserted in the phone line jack. This problem started after the power went off and on quickly two times. I have followed all the instructions that I have found to reset the modem, but to no avail. Is it possible that the phone line jack needs to be replaced.I have a gateway laptop with Vista program.
View 4 Replies
View Related
Mar 3, 2013
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
View 5 Replies
View Related
Nov 2, 2011
I am planning the following network setup.Get a server with 2 NICs, a router and a switch ,1st NIC is connected to Internet2nd NIC is connected to a router,A router is connected to a switch,All the client workstation are connected to Switch to access the server.I believe with this setup all my client workstations can browse the internet on their local machine via server.
View 11 Replies
View Related
Jun 17, 2012
Trying to setup split tunneling over Site-to-Site (Gateway To Gateway) VPN between RV082 and Win 2008 server. Tunnel seems to be ok, I can ping/access by IP hosts from both ends. But I can't get split DNS to work. Here is the setup
10.10.100.2 is the DNS server for xyz.local zone. It is at remote network.
The tunnel and routing work properly. I can ping 10.10.100.2 either from RV082 (system management - diagnostics) or from hosts at local network.
Moreover, I can run nslookup on a host from RV082 side (local network), set 10.10.100.2 as server to be queried and test dns resolution. names of hosts from xyz.local are resolved correctly. But. If I use nslookup on host to query RV082 as a DNS server and query for a host from xyz.local it responds that xyz.local is nonexistent domain. The same result I get trying to resolve/ping same name on system management - diagnostics page. Resolution of names from xyz.local fails. But Internet names are resolved
just fine.
I've tried to reboot the router, connect/disconnect the tunnel, set Domain Name fields of split DNS configuration pagein different ways including fqdn of hosts from xyz.local No effect. Just the same situation.
View 2 Replies
View Related
Jun 10, 2013
(Setup routing and iptables for new VPN connection to redirect **only** ports 80 and 443) Only my goal is a bit different. I am running a headless gui-less install of Ubuntu Server 12.04 that is being used for a variety of different purposes... I would like all traffic to travel un-prohibited through my ISP except for my transmission traffic. I have a VPN i subscribe to that allows me access for which I only want to direct a single port's traffic to. I am currently using a modified version of the code from the above link. My current code is below:
#!/bin/sh
sleep 200
DEV1=eth0
[Code].....
View 1 Replies
View Related
Jan 22, 2013
I run a small software development firm with around 15 network users. We currently have broadband DSL (only thing available in our area with decent up/down speeds - 2/20 respectively). We have 7 development (Win 2008/2012) servers and 4 sales people that tie up bandwidth with video conferencing/movies/music/etc..We aren't running a DHCP server (the modem/router handles DHCP) or exchange (we use gmail). We essentially have the broadband modem, a cradlepoint mbr1400 router as AP, and a 24 port unmanaged switch, a few wireless printers, and of course each employee has at least one other device connected via WIFI.
View 8 Replies
View Related
Jul 21, 2012
We have ASA 5520 acting as the VPN Server and Cisco 1941 router as EZVPN client. Since last few days client is not able to establish vpn connection. 1941 router is continuously generating the below log messages
001569: Jul 22 12:19:05.883 ABC: %CRYPTO-4-EZVPN_SA_LIMIT: EZVPN(VPNGROUP) Split tunnel attributes(51) greater than max allowed split attributes(50)
001574: Jul 22 12:19:07.835 ABC: %CRYPTO-6-EZVPN_CONNECTION_DOWN: (Client) User=vpn_user Group=VPNGROUP Client_public_addr=<client public ip> Server_public_addr=<server public ip>
004943: Jul 22 11:32:42.247 ABC: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the fragment table has reached its maximum threshold 16
View 3 Replies
View Related
May 21, 2012
I am using a 6500 with FWSM. I need to separate an internal server/HQ network from 3 or 4 different external connections. The external networks do not necessarily need to be isolated from each other.I have the option of using a 3 layer model: L2 Access layer to SVIs on the Distribution layer and then L3 to the 6500.L2 Access, connecting directly to the 6500s, with the SVIs on the FWSM.Is it better to have the FWSM outside the MSFC or Inside? Am i correct in thinking that "inside" vs "outside" is determined by whether the SVI's are configured on the FWSM or the MSFC? is there any performance impact from having the FWSM doing the routing instead of the MSFC.If the vlans are all configured on the FWSM, what is the 6500 doing, other than providing switch ports?
View 1 Replies
View Related
May 9, 2011
XP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu
View 1 Replies
View Related
Jan 14, 2013
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies
View Related
May 7, 2012
I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly?
View 7 Replies
View Related
May 26, 2011
- I just need internet in all 15 PCs - I do not want them to be connected with any sever locally or in network but my demand is internet on all system with good speed.
View 5 Replies
View Related
Jan 16, 2013
My fiance recently signed up for the Screen-wise Panel for Google research. Basically they monitor your TV usage and your internet usage. As part of the program they installed a Cisco WIFI router. I've got no issue with them logging the sites visited etc but I'm a little worried about them possible collecting private information (banking / work related stuff) that I don't want going out there. According to what I've read what's supposed to happen is they replace your router with the new Cisco router.The "technician" who came in and installed the router was actually a builder and not an IT technician and rather than replace our router he connected the Cisco router into port 4 of our router... I wasn't in at the time.
What I was looking to do is separate Port 4 of my router into a separate VLAN that can access the internet, but not access anything on ports 1-3, or the wireless. However, I want to be able to see everything on port 4 from the other side (in other words I want to see "into" the port 4 VLAN, but don't want them to see out). I also wanted DHCP to assign IP addresses correctly depending on where you were plugged in. In this example the first VLAN (your current router ip address) is going to be on 192.168.1.1, and the second VLAN (the new on we create on port 4) is going to be on 192.168.2.1.This is exactly what I'm looking to do, I could then connect the kids machines / tablets / ipods to the Cisco router and have the main machine and my work laptop on the main router... but I don't have a clue how to do it. </quote> Is this something that I am able to do with the Netgear router I own and is it hard to set up?
View 1 Replies
View Related
Jan 26, 2013
i have duel boot system with window 7 and ubuntu 12.10 i connect to internet through nokia mobile using serial cable. it works fine in ubuntu and used to work fine in window 7 also till last month. but now i am not able to browse internet in window 7. this shows connected but i am not able to open webpages despite using different browsers. network troubleshooting shows "DNS server not responding" error. i have tried ipconfig release ipconfig flush ipconfig renew etc. and resetting dns server address to google dns but to no avail.
View 22 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
Jan 15, 2011
i'm new, then i don't know what is my dns server names and ip
View 3 Replies
View Related
Feb 16, 2011
Have nearly new desktop running Windows 7 and cannot connect to Internet (BT broadband in wireless mode). Error message says 'cannot connect to proxy server'.
View 4 Replies
View Related
May 30, 2011
I want to open a branch office but need to access the same server as in the main office.How do I do this without losing speed?
View 2 Replies
View Related
Feb 2, 2012
What would be the ideal download and upload speed for a server of more than 50 people ?
View 1 Replies
View Related
Feb 8, 2011
Network connections lost Windows 2003 Server, Reload Drivers Still not working.
View 28 Replies
View Related
Jun 28, 2011
how can i store urls used by the client side in the server using java
View 1 Replies
View Related
Mar 27, 2012
The reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies
View Related
Jun 1, 2011
Half of the time i have to stay at hotel due to business trip. The hotel i stay will provide free internet broadband with cable but no WIFI. Can i set up WIFI if i have router?
View 2 Replies
View Related
Feb 10, 2012
I am using PTCL' DSL in my country. I want to know how can i increase download speed of stuff from internet?
View 2 Replies
View Related
Mar 2, 2012
would you explain the main differences between lms 3.2 and 4.2 cause my company is about to purchase the new version;
- how does it changed in taking reports ?
- how does it changed and improved in monitoring?
View 1 Replies
View Related
Mar 2, 2011
i need to change my computer setting so it connects to a broadband modem?
View 1 Replies
View Related
