Westell 6100-linksys Wrt54g Dd-wrt Configuration
Mar 23, 2012
i recently reflashed a linksys wrt54g v2.0 with dd-wrt (the latest stable release. i cannot for the life of me seem to configure it so that it works properly with my westell 6100 verizon modem. i would like to do so without placing the modem in bridge mode, as i had it set up prior to the reflash. this way i can remove the router when not in use.
my router settings:
wan connection type:auto config-dhcp
stp:disable
routername:DD-WRT[code].....
View 13 Replies
ADVERTISEMENT
Oct 18, 2011
Okay, I know there has to be something I'm doing wrong because 3 months ago I set up the same modem & router to work. Being the idiot I am, I reset my router to change the password (dumb I know) and now the router can't pass the internet signal from the modem on! 1. I've set the modem to bride/bridge and unchecked the private LAN box.release/renewed IP2. Used the modem's MAC address in the router. . Made sure DHCP set to obtain automatically.4. Reset, restarted seperately multiple times.It looks like from the status page that the router is obtaining an IP but it won't connect to the internet
View 2 Replies
View Related
Mar 28, 2012
At my home I have a Westell 6100 DSL modem connected to a computer.AT&T is the ISP and all filters are installed.I use my home computer via VNC applications from a remote location and I began to notice that the VNC local client session was being lost,,,over and over.It was discovered that the WAN IP was changing over and over and happens about once every 5-10 minutes,,,or so. While I have a dynamic WAN IP from ATT, I would not expect the WAN IP to change as often as 7-8 (or more) times a day. At first I thought it was ATT changing my DYNAMIC WAN IP.But, a review of the Westell log file is reporting lost connection(s),,,,,etc, etc,,,,,etc. over and over.Below is a list of the Westell log information showing several hours of behavior.The Westell diagnotics that were run and the SELF test run as expected.Looks like the DSL modem is going bad, a filter is bad, or the line is going bad and needs to be balanced,,,,etc..
Code:
All Entries
CURRENT MODEM STATUS
DSL Modem Status....... Up
PPP Session Status...... Up
Connection Type......... PPPoE
Time set from............. Local
[code]....
View 2 Replies
View Related
Aug 1, 2011
Where do I find security key for modem Westell 6100?
View 3 Replies
View Related
Apr 20, 2011
I'm unable to access the internet when I plug my modem (Westell 6100) into my router (Netgear WPN824). It works perfectly fine when I connect my modem directly to my computer though. It was working perfectly last night and for the last few years up until now.
I've tried sequencing, turning off my modem/router/pc while waiting two minutes in between each step but it doesn't work. I'm 100% sure the log in and password information to log in is correct (I use PPPoE to access the internet). I've tried resetting the router to factory settings and going through the setup but I get the same result. (Unable to connect)
OS: Windows XP
ISP: Verizon DSL/PPPoE
Modem model: Westell 6100
Router: Netgear WPN824
View 7 Replies
View Related
Nov 11, 2012
I have DSL via ethernet on my Mac through a Westell 6100 series modem/router, which also has a USB port. Is it possible to share my Internet connection, preferably via a cable not wireless, with a PC laptop by using the USB port (with an ethernet adaptor), or by splitting my present ethernet connection?
View 6 Replies
View Related
Mar 15, 2013
I have DSL via ethernet on my Mac through a Westell 6100 series modem/router, which also has a USB port. Is it possible to share my Internet connection, preferably via a cable not wireless, with a PC laptop by using the USB port (with an ethernet adaptor), or by splitting my present ethernet connection?
View 1 Replies
View Related
Oct 29, 2011
I just bought a Westell modem 6100 model online, and when I try to change the profile, I get a message saying: The server 192.168.1.1:80 requires a username and password. The server says: Modem Secure."
View 1 Replies
View Related
Nov 12, 2011
Wireless Router - DI-514,Modem - Westell 6100, Every time I refresh the 'View available Network settings' My Connection name pops up with other connections but then disappears after I refresh again and others as well disappear, but some stay. Right now I'm using the the wire the blue wire that connects me to the internet.
View 3 Replies
View Related
May 12, 2011
I'm running into the same problem. I'm trying to connect my 6100 Westell Modem as well, but I'm going through Cincinnati Bell Zoomtown. They sent me a disk & it does't have the right software on it. I was told to look online & have had no luck finding where to download. I have to use USB to connect. I'm at a loss at what to do. Have spent almost 3 hours on the phone with tech support at this point!
View 1 Replies
View Related
Aug 1, 2011
Earlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
View 5 Replies
View Related
Jun 9, 2011
When I hook up the Westell modem to my Linksys router WRT54G it wont work?
View 1 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Nov 24, 2011
I've got a WET200 connecting to a wireless router (linksys WRT54G) setup thru the WET200 site survey.Does the WET200 need to have an ip with the same sub net as the network the WRT54G is connected to?I have a laptop hooked up the the WET200 with a static IP. I cannot ping IP's of the same sub net on the network the WRT54G is connected to nor see anything on the internet?
WET200 connected to wireless AP WRT54G (192.168.23.3)
WET200 IP address = 192.168.23.8
Laptop IP address = 192.168.23.218 (connected to port 1 of WET200)
I can configure the WET200 via the laptop, but not able to see anything across the bridge?
View 1 Replies
View Related
May 22, 2012
I have a WRT54G with updated firmware. Today I saved my configuration to a config.bin file. When I tried loading the file, the admin screen went blank. Now I am no longer able to access either the internet or the router's admin page. Is a hard reset my only option?
View 6 Replies
View Related
Aug 21, 2012
I have a WRT54G router anf DSL modem. My router keeps losing connection, wired and wireless (My connection is not visible on any laptop). I tried briged mode on the modem and I tried the configuration CD. Everything works for some months or weeks. Sometimes the CD setup asks me for manual configuration. I am using modem to desktop connection?
View 2 Replies
View Related
Mar 3, 2011
I was trying to work with a friend set up his wireless router. He had the Geeksquad come and set it up and I have no idea what they did. A mess of wires. I noticed that I was able to log into the imbeded browser of the modem and the router from the main PC. I didn't think it was possible to log into the modem if it was set up in bridged ethernet mode. His internet is working but I was thinking that he may have problems with double NATing.Basically, I just want to know what options there are for setting up a router to a modem. I'm aware of bridged mode and setting up the router as a switch (not real knowledgable of this one). Seems like DHCP is enabled on both devices.
View 3 Replies
View Related
Nov 30, 2011
I have at&t DSL with Westell Modem/Router in Bridge Mode and Linksys Router connected. The internet is working fine, but I'm unable to forward ports on the Linksys Router. The ports are 80 and 37777.
View 1 Replies
View Related
Feb 20, 2012
I have a westell 7500 with fairpoint service hooked up to my DSL line. I have disabled woreless on the westell. I then have a linksys e-1000 connected to the westell 7500. I have one wired computer on that network, my imac/game server, my main PC, my wii and an ipod touch connected connected to the linksys e-1000 wirelessly. I want to forward port 25565 through these routers to my imac. How can I do this? I have tried portforward.com, and a million other things.
View 2 Replies
View Related
Apr 12, 2011
how can I track a dynamic IP address. The reason why I am asking is because my dad lives about 40miles from me and I would like to logon to his computer from my apt and my dad is currently using frontier dsl connection with a westell 6100 modem. Is there any software or what do I need to do to configure this?
View 6 Replies
View Related
Feb 7, 2012
I used these instructions to put my Fairpoint westell 7500 modem/router into bridge mode: [URL]. Then I hooked my new e3200 to the westell 7500, but no matter what I tried, I could not get any PCs hooked to the e3200 to be able to get to the internet.so able to get to internet too. My questions are:Is there any downside to doing it this way? (ie, not putting westell in bridge mode).Can this cause any slowness or conflicts? Any reasons why bridge mode may not have worked?
View 4 Replies
View Related
Sep 20, 2012
I Installed windows XP on my Alive 6100 computer, and now it wont detect my ethernet cable. I tried updating the drivers off the ECS website but nothing works. I cant go through ethernet or wireless, probably dont even have the drivers (I Installed the ones listed on the site).
View 2 Replies
View Related
Apr 7, 2011
I have a Westell Verizon 6100G Modem someone gave me. My service is with ATT using a Westell Windspeed modem, that is going bad. ATT wants $75.00 to send me a new modem. Is there any way to convert this Verizon modem to use it on ATT?
View 3 Replies
View Related
Aug 9, 2011
Where is the WEP KEY for a AT&T Westell router?
View 1 Replies
View Related
Mar 7, 2011
i have a westell 6110 that i want to upgrade to westell 7500; how to do this ?
View 1 Replies
View Related
Oct 8, 2011
How do I open my NAT on my westell 7500
View 3 Replies
View Related
Sep 22, 2011
I have a DSL modem and Linksys WRT54G wireless router for several years and haven't had any problems. I decided to move the router and modem to a different room. Upon replugging everything in, I can't get an internet signal from my router. My modem seems to work fine-all lights are on and if I plug my laptop directly into the modem I have internet access. But, if I plug the router into the modem, I can't get internet signal both wired or wirelessly through the router. All of the lights on the router turn on-showing I should be getting internet signal [power light solid, WLAN light on, internet light on], but my computer won't open a website. I've done reboots on the modem and router. The router was working great prior to moving it. My DSL company says everything is fine on their end. I receive a Ping back from the router as well. What else should I check or do I need to do?
View 1 Replies
View Related
Sep 1, 2011
I have a linksys router connected to four computers and putting out a wireless signal. I also have a PC upstairs I would like to get online, and have a WRT54G V5 wireless router that I want to use like a wireless USB stick. Is this possible without downloading additional firmware beisdes official Linksys firmware?
View 6 Replies
View Related
Aug 1, 2011
I have a bluray player that I want to get internet to that is downstairs. I would like to use my old Linksys WRT54g ver 2 router to do this. I just put DD-WRT firmware on it. I have a Linksys E1000 as my primary router. All I want to do is be able to to put the Secondary router (WRT54G) downstairs near the bluray player and run an ethernet cable from the lan port on the router to the ethernet port on the bluray player to get internet access. What is the best way to do this? Client bridge or Client mode?
View 2 Replies
View Related
Feb 24, 2012
I recently purchased a Linksys E1200 to replace my Linksys WRT54G. I'd like to utilize the WRT54G as a repeater. Is this possible, or do I need to buy a "repeater"? how to configure/set up the WRT54G repeater?
View 3 Replies
View Related
Jun 20, 2011
Where do I get the WEP key for my Linksys WRT54g router?
View 2 Replies
View Related
Jun 5, 2011
I am trying to connect a Westell 327W to a linksys etherfast cable/dsl router to support my new Kindle. The Kindle recognizes it but is unable to connect.
View 3 Replies
View Related
May 18, 2011
I have all the PS3 and Activision ports. What numbers go where in the router's port forwarding screen. My ISP says that the PortStart and Base Host Port should be the same numbers and the PortEnd should be the number at the end of the range (10070-10080 for ps3). I'm going with that for the PS3 TCP numbers, but don't know which numbers to put in for the PS3 UDP or the Activision TCP and UDP.
View 8 Replies
View Related
