i have a dsl modem tht is also wi-fi and has multiple ports to connect to internet. I want to be able to use a cable to connect to net on my desktop while allowing my bro to connect to net on his laptop through the wi-fi. Right now, we have to disconnect from the net on one to be able to connect on the other. Is there a way to do so without disconnecting?
View 1 RepliesThe goal is to add a 2801 router between a DSL modem and a switch and obviously still access the internet. I connected and configured as explained below and the results are:
- I am able to ping internet addresses from the 2801 router
- I am not able to ping internet addresses from userlaptop but I am able to ping LAN gateway (192.168.254.254)
I cannot understand why the internet requests from the user laptopuser are not routed to the internet but the router itself can access the internet.
INTERNET====DSLmodem=====CISCO2801=====unmanagedSwitch=====userlaptop
DSLmodem:
non-bridged mode and does the PPPOe authentication.
WAN interface: Dynamic IP address assigned by ISP
[Code].....
I'm currently undergoing CCNa academy so I got a "job" from my boss to configure Cisco 871 router. Unfortunately we just finished first semester at academy so there are some things that I'm still having hard time to understand. I managed to configure router so it connect to internet or to be exact it has internet access through another adsl modem that is in bridge mode. url...The problem is that users are not able to use internet when connected to this router. I'm able to access router through telnet ( ip 192.168.13.10) but that's it.192.168.13.0 255.255.255.128 is network that we use at work. 192.168.13.5 is IP address that is assigned to zyxel adsl modem ( If I'm correct, we could have used any address here since we are connecting this directly to router ? ) Zyxel adsl modem is connected to FA4 port on Cisco router. LAN cable is connected to FA0 port and from there it goes to switch ( it's some asus switch with 50 ports). [code]
If I ping google dns from router e.g. ping 8.8.8.8 it works. If I ping url... it doesn't work. Also I'm able to access router via 192.168.13.10 but if I use router as default gateway then I'm not able to access the internet.
We have an ethernet port on Cisco router 1800 connected to the ADSL modem. The router does ip nat translation, but users complained it is slow when they access to internet. [code]
View 1 Replies View Relatedhow do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
View 1 Replies View RelatedI have a laptop running Windows 7 and it is on a wireless network.The trouble I am having is, the Administrator account can get on the internet with no problems, however, another user cant.It was originally just a "User" account, however, I changed it to Administrator to see if that would resolve the problem. it didn't.
View 4 Replies View Relatedgot myself the Netgear internal PCI wifi adapter today & it works just fine on my Windows XP SP3 desktop.
The only problem I have is the question of restricting access to kids @ home. If it was an external USB adapter, I could have just taken it away but the concern is the device being an internal & always available one. The user configuration on the PC is such that there is 1 main administrator (The actual windows "administrator" account) that no one uses. Apart from that,
- 1 user with admin privileges (me)
- 1 limited account for the kid
- 1 admin privilege account for the kid again (for purposes like installation of games which require an admin account as mandatory)
I would like for the wifi PCI card to work only when I login to my account. There must be someway by which I could disable the device or make the internet inaccesible in the other accounts,, (but pls bear that 1 of the account that the kid uses also has admin privilege)
I tried disabling the device from control panel but in vain.. (tried something like the sys admins do in corporates ..) disabling the usb ports on the PC's in my office..!
They are all on the same domain but some of these users are getting dropped from the Internet, and email. Once they restart there PC it works for a couple of hours than it drops again. We also tried updating the network driver after doing that it works ok for a couple of hours after that they start lossing connection to the Internet and email again. We have tried several different things but have not being succesful in finding the issue.
View 3 Replies View Relatedgot myself the Netgear internal PCI wifi adapter today & it works just fine on my Windows XP SP3 desktop.
The only problem I have is the question of restricting complete internet access to kids @ home. If it was an external USB adapter, I could have just taken it away but the concern is the device being an internal & always available one.
The user configuration on the PC is such that there is 1 main administrator (The actual windows "administrator" account) that no one uses. Apart from that,
- 1 user with admin privileges (me)
- 1 limited account for the kid
- 1 admin privilege account for the kid again (for purposes like installation of games which require an admin account as mandatory)
I would like for the wifi PCI card to work only when I login to my user account. There must be someway by which I could disable the device or make the internet inaccessible in the other accounts,, (but pls bear that 1 of the account that the kid uses also has admin privilege)
I tried disabling the device from control panel but in vain.. (tried something like the sys admins do in corporates ..) disabling the usb ports on the PC's in my office..!
I live in a house with 5 other students. To be fair, it is in the middle of nowhere so the internet is probably very slow anyway, but here is my problem: Skype is so slow I can only just make a voice call, webcam chat is off the cards. YouTube and other videos are so slow to load I cannot watch them. My Xbox 360 constantly disconnects from the wireless, so I cannot play online.
View 6 Replies View Relatedrestricting access to internet for roughly 20 users. Right now we are connected using broadbandand using dhcp as assigned by common switch. All pc's are in a common workgroup. recommend me the hardware / software required to restrict this access.
1. Will I require a router as well as a switch ? or should I simply get a new switch ( for more then 20 users ) This would mean static ip for all users.
2. My idea is to create a AD server and use websense on it so that users who require internet access can still open internet sites but will be restricted through websense proxy.
Bought a Dir-600 from challenger, used it for 3 months and started expericing the common problems of loosing internet connection highlighted by many users here and in other forums. Would always have to do a modem / router power cycle to get it going again.Slightly after 3 months... the thing went dead. Can power up but no response. Cannot detect the modem.Got a one-for-one exchange at Funan. Used the 2nd one for less than 2 months. It just went dead on me! Same problem...
View 3 Replies View RelatedI have web server setting behind the Linksys ADSL modem, I set the DMZ IP to my web server IP so the external internet users can access my web pages.
This setup was working fine until I switched to “Linksys X3000” modem, external internet user can no more access my web pages.I had set the DMZ IP correctly in the new modem. The local LAN users can access the pages without any problem.
We've got Workgroup LAN at our office and the Server is configured by the OS “Windows Server 2008 R2”. Most of the users use OS Windows XP-Service Pack-2. Now, I want to see the Internet surfing status/activities done by any particular user/users at any time from the Server. You know that, some people enter into restricted sites which impose severe negative impact on the network. If I could trace from the Server any user of doing this, I shall block his Internet connection from the Server.
View 1 Replies View Relatedwhen I try to enable network internet connection on my computer it tells me that somebody else is using IP 192.168.0.1
View 2 Replies View RelatedIf there is something that cant control the bandwidth of our internet.
The problem is that one person is constantly hogging our internet by downloading and such and making it impossible to play games.
So is there anything that can make it so he cant use that much bandwidth so we can play without constant lag?
I have configured and tested an ASA-5505 that will be deployed at a customer's home. The ISP cable modem will connect to the E0 (outside) interface of the ASA. All other interfaces on the ASA are configured for the inside network 192.168.5.0/24. I have created a VPN site-to-site tunnel between this ASA and the UC540 to allow 192.168.5.0/24 subnet access to the internal networks on the UC540.
The user has requested that all the network devices used by the rest of the family will only need to connect to the Internet. They will not need access to the VPN tunnel and they will not need access to the computers on the 192.168.5.0/24 inside network. I was planning on performing the following tasks to get this to work.
I have an ASA 5510 with IOS 8.4. I want that only authenticated active directory users can pass the firewall.
View 3 Replies View RelatedI have a 2504 Controller (os version 7.0)with 7 access poins attached and with 2 vlans. one for regular users and another for gues users.
View 10 Replies View RelatedWe have a Cisco 3750 stack connecting to the MPLS router, able to ping 8.8.8.8 - [URL], the internal users on their own Vlan can ping the default gateway the 3750 switch but no further, trace route from the PC/Servers stops at the 3750 stack.We have the switch configured to ip route 0.0.0.0 0.0.0.0 to the public interface in the MPLS router, from the switch I'm able to ping the internet.
View 17 Replies View RelatedI am able to successfully connect to my ASA5505 via AnyConnect via a mobile device. Upon doing so, I lose internet connectivity. My access list appear to be correct to I'm sort of at a loss.
[code]....
My wireless users are loosing the internet(http and https) connection many times per day. I just check the ports configuration in the switch, but The problem persist. The device is a Cisco Aironet 1130 AG.
View 4 Replies View RelatedI'm looking into a way of routing users internet connection based on their username or group in a windows environment. Currently there's two ISP connections with their own proxy server. I want a user to be fully redirected to one of the ISPs based on who they are. I was hoping via IE proxy settings, this can be accomplished, but it looks like the primary ISP connection, is still getting most of the connections/routing.
View 1 Replies View RelatedHow does one configure the router so that Internet users can access internal company websites? The only thing that appears is the Cisco router login. Also I need to configure Terminal Services and its not on the list under Service.
View 2 Replies View RelatedI have a 2wire 2700hg-d (Qwest/Centurylink) router serving 3 or 4 computers. Is there a way I can either block or monitor porn viewing activity of users through the router?
View 2 Replies View RelatedI currently set up two LAN networks. But one of them (Router 2) will be open (no password). Will this create a security compromise? Can the Router 2 Users access information of users of Router 1?
Modem WAN > Router 1 WAN
Router 1 LAN > Router 2 WAN
The router 1 and 2 are broadcasting different networks and SSID.Is there any setting that I need to change, or this configuration is perfectly safe? both of them have DHCP enabled.
I heard there was this router that does not make other user slow their internet even if there are multiple users.
View 5 Replies View RelatedA client of ours has an 881-K9 router that they have configured a VPN on, this was setup and configured prior to my joining the company. This client now needs to add more usernames to the VPN on the router side, and I've both searched here, and googled for how to add users to the VPN on the router, the only thing that comes up is adding clients (from the client end PC), and nothing to show how to create the users on the CLI from ssh on the router itself.
View 1 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
I have router TP-link WR1043ND which cant handle more than 22 users?
View 4 Replies View Relatedi have tenda ADSL router using the internet of Nepal Telecom, Nepal and distributed to two users. now i want to limit the speed of the other user to least and i want to achive maximum speed of the subscription but have no idea to manage it
View 1 Replies View RelatedWith my old netgear router I could see and share files on my kitchen PC from the office PC but with the WRT54GL I can't.
I have a printer with a static IP that both PC's can see.