Cisco VPN :: Adding Users On 881-K9 Router Side?
Apr 7, 2013
A client of ours has an 881-K9 router that they have configured a VPN on, this was setup and configured prior to my joining the company. This client now needs to add more usernames to the VPN on the router side, and I've both searched here, and googled for how to add users to the VPN on the router, the only thing that comes up is adding clients (from the client end PC), and nothing to show how to create the users on the CLI from ssh on the router itself.
View 1 Replies
ADVERTISEMENT
Dec 28, 2012
She has comcast xfinity with a the SMCD3GNV router which if you ever look it up has the worst wireless signal imaginable and I can second that. I was hoping to not have to touch the SMCD3GNV router and just add on to it by attaching a secondary router as a wap.What I plan to do (which I am sure has been exasterbated in forums but just want clarity) was to disable DHCP on the new n router ( cheaper than official wap) and set ip out of SMCD3GNV router DHCP ip range but in same subnet mask so probably 192.168.1.2. Then connect the SMCD3GNV router to the new router via ethernet and dont use wan port. Is this basically all I have to do? Do I need to change the channels on either devices since their next to eachother? or will them being next to eachother and same channel cause interference? I have read I can call comcast and turn the smcd3gnv into a bridge ( plain modem) but I would rather avoid calling them and see if 2 wireless access points next to eachother is okay.Also, I plan on doing this by going to microcenter.com and getting a router for 24.99 or less with a coupon I have. Is there any on their website that you would recommend for this setup? Also if you could check the wap on their website and see if you think its worth it to get one of those instead if under that price as well. I want to utilize wireless n signal . Also, the xfinity service she has is rated for 50mbps download and cannot remember the upload , I have tested this wired and it does actually achieve this or greater.
View 5 Replies
View Related
Jan 30, 2013
My E1500 enters a state where the LAN-side (broadcast, etc.) works, but the WAN-side (internet connection) just goes away. If I go unplug and replug the E1500 the internet connectivity comes back.When this happens, the wireless indicator on my desktop (Dell with Intel wifi) says I have an internet connection, but I clearly don't.
View 2 Replies
View Related
Dec 20, 2012
how do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
View 1 Replies
View Related
Mar 16, 2011
I have a Cisco ACS 5.2 and have set it up as a RADIUS server. I was wondering if there is a way to add and update users automatically? We have a large number of users > 1000 that need to be added into the system and I don't want to do this manually. These users also update their passwords on a regular basis so I would need a script that would update the users automatically without any user intervention.
View 4 Replies
View Related
Feb 9, 2013
how to add VPN users for a Prosafe VPN firewall fvs318v3? I want to do a home to work vpn connection for several employees. All I am seeing is a place to put in IP addresses. Surely there has to be a way to set this up based on user name and password.
View 9 Replies
View Related
Mar 13, 2013
i configured cisco asa 5520 as cisco ezvpn server and cisco 891 as ezvpn client .the configurtion is working fine.i am using client mode on the ezvpn client side.but my quesion is , is it possible to communicate to ezvpn client side internal ip from the ezvpn server side?and one more thing what is the benefit of network extension mode on the client side and how it will work what are possible changes need to do in the server and the client side.
View 4 Replies
View Related
Mar 17, 2013
I'm trying to setup an ASA and a UC540 side by side, to utilize the ASA for data networking and the UC540 for voice. This 'should' work fine, I just seem to be having an issue where the ASA seems to be blocking traffic from the voice network as it passes through.So here is the LAN setup:ASA: 1.1.1.1UC540: 1.1.1.2The UC has a voice vlan 10.1.1.1/24 and a service module at 10.1.10.1/30My PC uses the ASA as its default gateway, 1.1.1.1The ASA then has static routes to the UC networksRoute 10.1.1.1/24 1.1.1.2Route 10.1.10.1/30 1.1.1.2Ping from PC to the UC networks works fine. However, ping from the UC networks to PC fails. ASA logs show traffic being denied due to not having an established connection or something.My guess is that the traffic is being blocked because the egress and ingress paths are different? Traffic from the PC goes to the ASA, then gets routed to the UC and it works. However in the other direction, traffic from the UC is going directly to the PC and bypassing the ASA, because its a directly connected network and doesn't have to route through the ASA to get to the PC. The reply traffic from the PC DOES go through the ASA following its route table, thus the issue of the ASA not seeing the established connection?Same-security inter and intra interface is enabled.So I think I see the issue, I just don't know how to fix it. Is there something I can configure on the ASA to allow for this? My only other option would be to configure a /30 on a new vlan to handle the routing between the UC and ASA or something, but that seems like its going to make this simple setup way too complicated with extra networks, vlans, trunks, etc.I am running ASA version 8.4.5?
View 1 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Jul 11, 2011
Is it possible to configure Easy VPN on brach side which has 877 series router and ADSL connection for internet such a way that for internet traffic it will use the local ADSL line and for the server in HQ it uses the tunnel.or for internet also it will go thrugth tunnel and uses internet link at the HQ?
View 3 Replies
View Related
Oct 9, 2012
Since this router already set up for IPv6 and Dual-Stack traffic, would it be possible to give it the ability to get its IPv6 prefix from the WAN side of the router.
Example:
I have Comcast, and as long as my modem and router support IPv6, with the router also supporting DHCPv6-PD to get the /64 prefix from comcast.
I now have an RV180W so this is not an issue for me, but my father is inheriting the WRVS4400N from me and he is also on Comcast.
View 2 Replies
View Related
Jan 23, 2013
Basically I have a win2000 server running as a VM in my computer with a secondary LAN address(Different subnet) which acts as a gateway for the other devices on my network (e.g. my wifi-router has DHCP relay set to my VM's address). The VM uses another network(internal NAT) for accessing the Internet though my computer. So far, I've managed to set up the DHCP and routing. Other devices on my network have access to the internet. But, since my computer has only one NIC, and even though the VM uses a secondary IP address, it's still on the same network as my internet connection. There are computers that belong to other people, who I do not want to give access through my router(even though their computers are picked up by my DHCP). I was given only one IP address for usage on my computer. This is why I wanted to add some kind of an authentication procedure(like some sort of PPPoE login maybe?)so as to prevent unauthorized usage my my connection. The question is, 'What are my options for the authentication procedure, and where do I start?' If my explanation was unclear.
View 6 Replies
View Related
Oct 17, 2011
I have a central office and two branch offices, these offices are connected by a private routing service that has no connection to the Internet, the telecommunications operator in each office installs a router with a LAN and a WAN IP and configuration of these devices cannot be changed except the LAN IP. Only the central office network that is 192.168.0.0 have a router that has internet access. Remote offices have no access to the internet, what is needed is that remote offices can access the internet using ADSL router 192.168.0.254 at the central office. There are a small devices in each remote office that must connect to the internet and do not support any configuration except IP, mask and gateway, for example you cannot add a static route. Currently the pc's at remote offices has IP communication with the server from the central office using a static route. put some VPN routers between each LAN and the operator's routers (where RT yellow star appears in the diagram) and put the hosts of the two branch offices same IP range that the central office network? I had thought to use RSV400 routers?
View 6 Replies
View Related
Oct 5, 2012
Device: Linksys E1500 - firmware: 1.0.01? I've got a static IP setup for a small remote office and want to keep tabs on their internet connection by pinging it via a monitoring program we use. However, the router seems to not responding to ICMP.
- Filter Anonymous Internet Requests is unchecked.- I've verified that the Static IP is correct.
- I've tried pinging from several remote locations on different connections, with no avail.
I can't seem to figure out why i can't ping this device. I just want to make sure there isn't a setting in the wireless router that is preventing echo replies.The only other thing i can assume is that Comcast is filtering ICMP on their side of the WAN connection.EDIT: Here's a traceroute from my PC to the WAN side of the Linksys....
Tracing route to 50-194-XXX-XXX-static.hfc.comcastbusiness.net [50.194.XXX.XXX]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 172.25.2.1 2 6 ms 16 ms 6 ms 10.0.0.5 3 9 ms 8 ms 8 ms 10.0.0.1 4 7 ms 7 ms 7 ms 10.0.0.2 5 8 ms 7 ms 7 ms ont-static-208.57.XXX.XXX.mpowercom.net [208.57.XXX.XXX] 6 7
[code].....
View 3 Replies
View Related
Jan 27, 2012
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 1 Replies
View Related
Mar 3, 2012
I have a BEFSR41 (wired) router. On the LAN side, I'm using all static IPs, and have the local DHCP server turned off. On the WAN side, I'm using DHCP. When I plug my laptop (which runs Windows 7, and has a static IP set up) into the router, sometimes I can't connect to any hosts on the WAN side, even though other machines on the LAN side can connect to hosts outside. If I run Wireshark, I see the following happening over and over. [code] When this occurs, the laptop can nevertheless connect to the embedded web server running on the router, and, there, I can tell the router to release and renew its WAN-side DHCP lease.
View 3 Replies
View Related
Oct 13, 2011
I have a DGL-4500 D-Link router as a base. And a DAP 1522 Ethernet Bridge I use to connect 3 devices and another router I am looking to host a media Server for the house(on the bridge).
View 5 Replies
View Related
Jul 27, 2011
It's been a pretty darn good router for about 8 months now, then today one of the wireless connected PC's started to go intermittent internet, and then dropped the connection.
At first I thought it was the PC, but after checking other connected items (wii, PS3, another pc, 2 ipods, and 2 printers) I discovered all the wireless connections were dropped, and no one could see the SSID. An hour unplugged fixes nothing. 2 wired ports are working fine though.
When it's uplugged and then plugged in, all the little lights come on, then go out, and then, only the 2 wired port lights come on, nothing else.
View 2 Replies
View Related
May 7, 2012
I am using Linksys E4200 wireless router. I connected two machines, this way.
|LAP1|--------(LAN ethernet connection)----------|LinksysE4200|-------(Internet wired connection)--------|LAP2|
On the Linksys E4200, the Internet wired connection side, I gave static IP address which is in the same network range as that of LAP2.When tried to ping from LAP1 to LAP2, ping doesnot happen. Any settings by which I can ping from LAP1 to LAP2.
View 2 Replies
View Related
Dec 18, 2011
My Linksys WRT110 doesn't seem to have the range to make it to the other side of the house. What range expander is compatible?
View 5 Replies
View Related
Dec 10, 2011
E3200 works great until I enable QoS. The device uses QoS and works find until reboot. If QoS is enabled and the device is rebooted, its stops routing from LAN side to Internet side. Administration-->Diagnostics allow me to ping/trace route to Internet sites and local LAN clients but cannot reach Internet from local LAN.
Windows networking icon indicates "No Internet access". I can ping other devices on local LAN.
Disabling QoS restores routing and you can re-enable QoS after that and all is well. Unfortunately, if there is a power failure when I', not there to disable/re-enable QoS afterward, other household members can't use the Internet till I get home.
Wondering if any other QoS users have observed the same problem.
View 7 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Sep 11, 2012
I have an E4200 functioning with a new Comcast/XFinity cable modem on the public IP (Internet) port. That modem provides a DHCP address to the router (currently 50.129.x.x./255.255.254.0) The problem is that this new setup is leaking COMCAST DHCP responses through the E4200 to my WiFi clients. Most of the clients (newer iPODs, laptops) are smart enough to behave correctly and use Wifi Protected Setup. This problem means that one older iPOD seems to be receiving the Comcast DHCP (as 192.168.33.0/24 range) instead of E4200 Wifi DHCP range (as 192.168.1.0/24 range). I imagine the most direct solution is to pull the public connection briefly and allow the iPOD to fetch a valid WiFi DHCP from the remaining DHCP server on board the E4200. HOWEVER, I'd like to configure the router to suppress all DHCP packets from the Comcast network - or otherwise make sure the WiFi clients only receive DHCP from the router and not the Comcast modem.
View 4 Replies
View Related
Dec 21, 2012
I have E1 interface that supports 2Mbps and i need to connect Point to Point , my question is can i add 2 more E1 interface on my cisco router and configure it using channels on that link so i can increase my bandwidth up to 6Mbps.
View 5 Replies
View Related
Sep 26, 2011
We need to setup a VPn to another company, but we both use 172.16.x.x/16. Would I need to get both sides to setup a VPn using 2 different subnet ranges and then get us to NAT it to our own range?I was thinking of making our side 10.7.x.x/16 and their side 10.6.x.x/16
View 1 Replies
View Related
Nov 14, 2011
We will be getting a circuit from the same ISP at two of our sites and will be doing eBGP. Couple of notes. 1. We are fully aware of the risks associated with depending on a single ISP and have mitigated them as much as possible with the ISP. 2. We will be getting assistance on the eBGP setup from the ISP, so I’m not as concerned with that config at this point.
Site Summary
Site A:Cisco 2900 Series (RtrA) connected to single Ethernet based ISP circuit (ISP-1-A)eBGP will run between RtrA and ISP-1-A, default routes from provider onlyLayer 2 Switch (SwA) connected to LAN of RtrA and uplinks to SwB
Site B:Cisco 2900 Series (RtrB) connected to single Ethernet based ISP circuit (ISP-1-B)eBGP will run between RtrB and ISP-1-B, default routes from provider onlyLayer 2 Switch (SwB) connected to LAN of RtrB and uplinks to SwA
I need advise on the LAN side redundancy. Our goal is redundancy; load balancing is not a concern (If load balancing ever becomes a concern I will look at GLBP). We have several devices on the LAN side of the routers that can only use a single gateway. Given that I’ve surmised I need to use HSRP in some way for LAN gateway redundancy.
1. HSRP with Object Tracking, No IGP.HSRP handles LAN gateway failover if a router dies. Object tracking ensures LAN gateway failover if an interface fails or if an interface is up, but there is an upstream traffic issue. ie. track the physical WAN interface and use an IP SLA icmp to track a specific upstream IP incase of an upstream traffic issue.
2. HSRP with OSPFHSRP handles LAN gateway failover if a router dies. OSPF redistributes eBGP default routes to RtrA and RtrB so that each router should have a route to the ISP even if they loose their local ISP circuit. i.e if ISP-1-A on Router A goes down, Router A knows to send traffic out ISP-1-B via RtrB. In other words, traffic enters RtrA LAN, but exits on RtrB WAN.
3. HSRP with iBGP HSRP handles LAN gateway failover if a router dies. I have no experience with BGP, but assuming this would work similar to the OSPF solution above except for the required iBGP config and possible route reflectors?
View 2 Replies
View Related
Feb 6, 2011
I work most of the time at home so my work installed a WatchGuard Firebox SOHO 6 router at my place so they could make a secure VPN connection between my laptop and my work.All the other computers and gaming consoles at my home are also connected to this router. But they aren't connected with the VPN. Click here for a scheme of my current configuration.Now my question is: Can I place an extra wireless router (eg. D-Link DIR-855) between my cable modem and the watchguard router without blocking the VPN connection?I want to use the watchguard for my work laptop only and the new router for all the other computers and laptops.Click here for a scheme of the configuration that I want.
View 4 Replies
View Related
Dec 17, 2011
I have a home network that is up and running. It consists of a cable modem, a non-wireless router and two computers.My cable provider provides me with two DHCP IP addresses that are pingable on the Internet.I would like to connect a second router to my network and give it the second DHCP IP address that my Internet providers gives me.
View 9 Replies
View Related
Aug 19, 2012
I have 1 computer, desktop, and would like to hook up a wireless to use for phone and kindle,etc. Question is shoud I use a switch or router? I have a netgear fs105 and hooked it up but was told it's not wireless (that's how much I know). Have Vista. and dsl.
View 2 Replies
View Related
Dec 3, 2012
I currently have DSL and I have my router connected to the phone line in my home office and have 3 computers (2 business & 1 gaming) connected to the router via ethernet cable, works great.What I want to do is take the gaming computer to the game room in the basement and hook it up to the internet down there. Since it's a gaming computer I want to connect it to a router with ethernet cable for the fastest possible upload and download speeds (I do not want to use WiFi because I play flight sims and FPS and WiFi is too slow/laggy for online play).
1. Can I connect a second router into the phone/DSL line in the basement then hook up the gaming computer to the second router and get internet access like I have in the home office?
2. If I ran an ethernet cable from the home office router to a second router in the basement, would the long length of the ethernet cable adversely affect the connection speed (bit rate) of the second router? (would I get slower internet access in the basement?)
View 2 Replies
View Related
Jan 17, 2013
I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies
View Related
Jun 12, 2011
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies
View Related
Nov 10, 2011
I have an E1000 router and recently moved to a basement apartment where the only internet access comes from a single Ethernet cable running out of a router upstairs. I can connect to that network (it is family) but ideally I would like to connect my router and create a second network so that I can connect my printer and other devices independently of the upstairs network.
View 2 Replies
View Related
