Broadband :: Configuring DSL With 5 Public Address?
Jun 23, 2011We will acquire a DSL connection with 5 static public address. How can I use the 5 static public address using a linksys router. Is it depends with linksys router model?
View 2 Replies
ADVERTISEMENT
Cisco WAN :: Configuring 861 NAT With Multiple Public IPs
Jan 20, 2012I've replaced my dead ASA5505 with a 861-K9.Our ISP provides a subnet of public address /29 (wan side) by example: 200.200.200.xxx /29,we have 3 servers (lan side) in the example 10.1.1.xxx /24 is the same case than Johnatan, the only difference are the public addresses. [URL], everything is ok when NAT via the FE4 public address, but when do the same with other public IPs doesn't work.
View 7 Replies View RelatedLinksys Wired Router :: RVL200 / RVS4000 Possible To Assign Public IP Address As Local IP Address?
Feb 28, 2011Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedCisco Firewall :: Configuring A5505 Setup Public Server And DMZ
Oct 8, 2012Setup:
LAN (192.168.1.X, with .3 as gateway)
DMZ (192.168.2.X with .1 as gateway)
WAN (X.X.X.146 as primary public IP, .145 as gateway and .147-150 as additional public IPs)
I want to set it up so that X.146 is where all my outbound traffic appears to originate.I want tcp HTTPS and SMTP to be allowed from the WAN (via the X.147 IP) to a specific server (192.168.1.11) on the LAN.Also, HTTP traffic to X.148, X.149 and X.150 should go to DMZ and 192.168.2.8, 192.168.2.15 and 192.168.2.18 respectively, but I haven't added that to my config yet. Looking to get the HTTPS and SMTP ones working first, then I'll fix the others (one step at a time)I've got contact with the outside world when I've configured it using the ASDMs "Public Server" interface, but it refuses to properly establish the connection, I get a "SYN timeout".
My config:
: Saved
:
ASA Version 8.2(5)
!
hostname kcisco
enable password X encrypted
passwd X encrypted
names
[code]....
Broadband :: Re-direct A Public Router To Port?
Aug 20, 2011I am trying to remotely access my PC from my HP Touchpad. I have program to do that but my public router is blocking access. The program says to redirect that router to port 5900. Since it is a public router I can't find how to access the public router to redirect it.
View 3 Replies View RelatedConfiguring D-link Wifi Dsl-2750u For Reliance Broadband?
Aug 6, 2012configure my D-link wifi Modem DSL-2750U for Reliance Broadband.I dont understand codes but a simple explanation and step by step
View 3 Replies View RelatedHow To Configure Public Ip Address On A Router
Oct 8, 2012i received a public ip from my ISP and need to configure to enable access my server remotely
View 1 Replies View RelatedHow To Assign Public Ip Address Using Router
Jul 14, 2011I have a public IP and I want to be able to view my three systems connected to a linksys router from the internet. How can configure the router to see three systems with just one Public IP address whenever I am on the internet?
View 5 Replies View RelatedCisco Firewall :: 80 / 443 - How To NAT Public Address To DMZ
May 13, 20111. how do I nat a public address to a dmz address.
2. how do I open port 80/443 in the public to this address?
Cisco VPN :: Public IP Address For ASA5505?
Sep 7, 2011I have a ASA5505 that I need to allow IPSEC and SSL VPNs through. The ASA is connecting to a BT Business ADSL router, what address should I be using on the ASA outside interface that will allow the ASA to be reachable from the Internet?
View 1 Replies View RelatedRouters / Switches :: Create A Public LAN Address?
Mar 7, 2011i want to connect dvr to the internet i need the step to take and process of creating a public LAN Address
View 1 Replies View RelatedGet Multiple Public IP Address From The Modem Using Switch?
Jan 25, 2013My ISP assigns IP's through a standard motorola cable modem via DHCP server. I can pay extra for a persistent IP which uses the MAC of my switch and assigns an IP. Is there a way to get multiple public IP address's from the modem using a switch?For example. Can I plug the modem into the switch and then plug a computer server into the switch and get an IP assigned to that servers MAC address and then also have another server attached to another port on the switch and get a different public IP for that servers MAC address?
View 7 Replies View RelatedSet DMZ With Multiple Devices On A Single Public Address?
Apr 9, 2013I have a i-ball 150M wireless-N ADSL2+ Router device in that , in the NAT tab, i have activated DMZ at my static ip with a private address 192.168.1.224 , so that that ip enabled device can be access to anywhere in public network.I want that using this single static ip , How to configure two private address devices in DMZ, so that both of ip enabled devices can be access in public network.
View 3 Replies View RelatedCisco WAN :: 1841 - Public IP Address Behind Router
Mar 8, 2012I'm really bad on networking so I have a question about NAT. I got two public IP addresses from my ISP: 92.x.x.252 - 92.x.x.254. 92.x.x.254 is configured as secondary on external interface and clients will use it two connect (vpn) it from outside through cisco 1841 to zywall p1 with wan ip address 92.x.x.253. Is this configuration (look at picture) allowed? How can I route traffic from 92.x.x.254 to zywall p1, if posible?
View 10 Replies View RelatedCisco WAN :: Assigning Public IP Address On ASA 5505
Jul 25, 2012My company wants to create a VPN Tunnel to allow a remote office to connect to ours. I purchased 2 ASA 5505 and I was expecting to be able to set this up without any issues. Sadly, that is not the case.
What I'm having trouble with is configuring my Public IP Address to the device. I go through the setup wizard and enter the IP Address like normal, but I have no option to input my ISP's subnet, Gateway or DNS. Without those, I get no internet connection. I know there is a way to do this, but I'm stumped.
My Specs:
2 ASA 5505 series
ISP Modem (Which they control) - SMC SMCD3GN with DHCP disabled
Protocols / Routing :: Cisco 1841 - Cannot Use Public IP Address
Jun 5, 2012Am having an issue with my cisco 1841. I recently brought some IP Publics. Now that i need them i just can't use them, I don't know much about routers but till now have successfully manage to do some stuffs with the router after googling ,OK we already have some other ip publics and when i look at the config file i can see something like this:
View 3 Replies View RelatedCisco Firewall :: ASA5520 - Cannot Use Public NAT Address From Any Of Other Interfaces
May 31, 2012I'm having a weird issue with an ASA 5520 (Ver. 8.2) of a customer. The scenario is as follows:
There is a sub net (on a sub interface) "Guest" which basically is allowed unlimited access to the internet. Traffic is source Na Ted through the ASA to the outside interface. This works fine.
There is on the "inside" interface a server which can be accessed from the outside via a public IP address. On the ASA this is implemented as a static NAT entry. This also works fine.
Now the customer wants to access the server on the inside from a client of the "Guest" interface using the public (Na Ted) IP address. Reason for this is, they have an application with hard programmed IP address inside and want to run some life tests. However, this kind of traffic seems not to be passing through the ASA.
What I have tried so far:
- examined, if a hairpin scenario could be applied here, but it seems not, as I have traffic traveling between interfaces not out and in to the same interface.
- enabled the option "enable traffic between two or more interfaces which are configured with same security levels" and also "enable traffic between two or more hosts connected to the same interface"
- when I use the real addresses of the host, it works, so it shouldn't be an issue with the firewall rules
So any reason why I cannot use the public NAT address from any of the other interfaces?
Cisco VPN :: 3845 Public IP Address Is Changed / VPN Is Disconnecting
Aug 29, 2012I've configured a easy VPN between cisco 3845 and cisco 871 router, 3845 is VPN Server.I am facing problem at client router ie.whenever The public IP address is changed the VPN is disconnecting.
View 3 Replies View RelatedBelkin Routers :: N150 - Can't Assign A Public Ip Address
Jan 8, 2013I have a n150 and it only allows private ip addresses for the lan setup. Is there anyway to assign a public address? I need to have the DHCP use a public range and I can't do that unless I can set the router to a public ip.
View 2 Replies View RelatedCisco WAN :: 1941 Cannot Translate Private To Public IP Address Using NAT
May 4, 2012I have 5 workstations with 2 servers but the backup server (black) is shut down intentionally.I have 1 cisco gigabit unmanaged 8 port switch and 1 cisco 1941 vpn router.The cisco 1941 vpn router is configured for IPVPN connection to other branches.
Challenge:
1. Configure NAT to enable the 5 workstations to be connected to the internet thru the router to the ISP.
2. Configure NAT to enable the server to be accessed from outside using the public IP address provided by the ISP. [code]
Verification:
1. I can ping other pc on 10.71.5.0/24 network.
2. When I typed in the ISP's public ip address on the browser, i got into the modem user interface for configuration.
I still can't connect to the internet. When i do tracert, it stops on the 192.168.15.1 hop and didnt continue. This shouldn't be the case since i want to connect using the GE0/1 outside port for the internet.
Cisco Firewall :: ASA 8.4(3) - Access To Public IP Address From Inside
May 22, 2012I need to connect from an inside host to a host located in the DMZ zone for DNS queries. The host in the DMZ zone has a static NAT to the outside. The point now is that I would like to connect from inside to the NATed outside address, means to the public Internet address.
Inside host: 10.0.0.1 -> PAT for 10.0.0.0/8 to 20.0.0.254 (Outside Interface)
DMZ host: 192.168.1.1 -> NAT to outside to 20.0.0.1
The traffic should be 10.0.0.1 udp>1024 to 20.0.0.1 udp=53. The source IP address on the outside interface now is 20.0.0.254 (according to the PAT), the destination IP address 20.0.0.1. The DNS reply from 20.0.0.1 should go back now to 20.0.0.254 and then to the inside host 10.0.0.1.
I know that on the PIX it was not possible, to have outgoing traffic on the outside interface which immediately enters again the same interface. Can I realize this scenario with the ASA 8.4(3) release now?
Cisco Routers :: RV180W - Outbound Public IP Address?
Mar 26, 2013What I'm trying to do seems pretty basic, but I cannot get it working on the RV180?I have 5 Fixed IPs. Using Access Rules I have configured a few inbound rules with specified WAN Destination addresses and these are correctly port forwarding these inbound ports on the specified Public IP addresses. Perfect!
However, for outbound, I need to do the equivalent for one public IP for outgoing SMTP so that our mail servers public facing address is not the standard WAN address and therefore will not fail a reverse DNS lookup. At the moment I have emails bouncing all over the place and panic has set in. I thought the SNAT option was the soltuion, but that just seems to break traffic flow completely on the specified port. I had this working no problem on my old Netgear, but I had to replace it due to throughput limitations.
Cisco Firewall :: ASA 5505 - Public Static IP Address And DMZ
Feb 3, 2013I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
Networking :: Thompson Router And Public IP Address With ST546
Sep 13, 2011I have a Thompson ST546 Router and I want to give it a public ip address and give two servers behind it public ip addresses as well.Now I am having great trouble getting this set in the web interface.
My router IP address is 91.85.232.65 with .66 and .67 will be the two servers. What is the subnet for these ips? Is it 255.255.255.248?
I have assigned my server the public address but if I try to ping it I am getting no response as if the ip is only a local address. My server is windows server 2008, is there a setting to turn ping on/off that I might have missed? I know the server is pingable internally.
Just to make it clear my ISP has assigned me IPs x.65 to x.70 for my use
Port Forward DVR IP Address - View Cameras On Public Website
Jul 12, 2012I recently installed a First Alert Security System and assigned IP address to the DVR but within the DHCP (After reading many threads, I will asssign, ping and create a static IP outside of the DHCP, maybe this will resolve the issue). I am able to view the cameras on my iPhone and HP Laptop but only internally on my network. I am trying to port forward my DVR IP address to be able to view the cameras on a public website. Although I am going to chcek and see if assigning an IP to my DVR outside of the DHCP and hopefully this will be it, I am afraid that my CradelPoint CRT 500 Modem will not support it. I read on one thread that this is a common issue after you have exhausted all the options. How can I be sure that my modem supports that my router port forwards? I want to avoid configuring to run in bridged or pass-through mode.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 V2 - Block Public IP Address?
Feb 2, 2013i got an E4200 V2 and it is updated to Linksys Smart Wifi firmware.. Is it possible to block a specific public IP address?
View 4 Replies View RelatedLinksys Wireless Router :: EA4500 Cannot Change To New Public IP Address
Jun 23, 2012I have noticed that after the new Firmware Update, the EA4500 will not change to a new public address. I have check my logs and my IP Address is the same going back to a 03/25/2012. I changed my router back to my old E4200V1 and it changes to a new addresses when the old one expires.
View 3 Replies View RelatedCisco Firewall :: ASA 5505 Port Redirection On Same Public Address?
May 26, 2012We have 2 TS (Terminal Servers) and have configured the 1st RDP using my public address (say 8.8.8.8) on port 3389. it is working very well of course. However I need setup my 2nd TS but will use port 7777 on the same public address which is not working.I am using ASDM 6.3 and firmware 8.3.1.Is this a limitation for this IOS?
View 6 Replies View RelatedCisco VPN :: 5510 - Changed Public IP Address / No Access On Native LAN
Jul 11, 2012i'm running a 5510 asa and the vpn has been working great for a while. We recently change our network provider so i had to change the public ip, and dns on the firewall... now i can still connect via the vpn and browse accross my mpls to other sites, but cant really access anything on the native lan that the firewall resides on?
View 9 Replies View RelatedCisco Firewall :: ASA5510 - Change Public IP Address On Outside Interface?
Mar 10, 2011we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
Cisco Firewall :: 2nd Public IP Address On 5510 That Points Nowhere Internally
Mar 15, 2011Will I break anything if I create a second IP address on the physical external interface of our ASA 5510? I want to point it nowhere internally but want an active interface that can be vulnerability scanned but won't lead anywhere internally.
View 9 Replies View RelatedBroadband :: How To Know Others IP Address
Jan 27, 2011Me finding my friends IP. I know its not good finding others IP but i need that seriously.
View 4 Replies View RelatedCisco WAN :: Configuring IP Address On A VWIC2-1MFT-T1?
Mar 19, 2012I have not worked on the new VWIC cards lately. I would like to know how I can configure the serial IP address like we used to do in the older T1 DSU WIC cards. I do not see any interface that shows as serial. I have configured the controller as a T1 controller but still no luck.
View 1 Replies View Related