Im attempting to connect to a password protect WAP2 Personal Wireless Network (I have Windows Vista). Unfortunately I can connect to the network but it will not Identify the network therefore I cannot connect to the Internet.
I have tried turning off the router and my computer, I have also tried both of the windows fixes for this problem (Reseting the network adapter and resetting my IP settings).
I recently got my laptop fixed after it being out of commission for about a year (it turns out there was just too much dust collecting in it) and when I got home and tried to connect to my wifi network, I didn't have internet access. I received a message that said I had sucessfully connected to my network but it was only a local connection - no internet. It also shows up as "Unidentified Network." This is peculiar to me because my boyfriend's laptop is able to connect to the internet wirelessly just fine, and I am currently using the wifi on my iPhone. I ran the ipconfig and several ping tests in cmd and used a wifi inspector.
Windows IP Configuration
Host Name . . . . . . . . . . . . : owner-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]...
I'm using a coaxial networking system and would like to electronically identify each section of coax in my network with a mac id for tracking purposes. Is there any way to do this without taking much space? Is there a microchip that I can install,preferably something that can withstand extreme environments?
View 4 Replies View RelatedJust bought a Sony Bravia KDL-46EX723 today and i am currently trying to connect it to my BT home hub via a "wired set up". BT home hub does not seem to be detecting the TV at all, when i try to do an auto set up it searches for a while and then comes back with, cable connection:failed, local access:failed, internet access:failed.I have went on to my network page to see if it was connecting to anything else and it is finding my external hardrive no problem via the Ethernet cable.I have tried looking at my computer IP details and adding them manually to the TV, but no joy, just comes back with the same errors.
View 7 Replies View RelatedI recently got a new computer from work, and it won't connect to my home network. I restored it to factory condition, and reinstalled the drivers for the wireless adapter card, but it won't identify my home network. The network adapter is a D-Link WDA 1320 and I'm trying to connect it to my home network which is AT&T Uverse, and the router is a 2wire 3800hgv-b. Hopefully that is enough information for at least an educated guess, I'm not so hot when it comes to home networking matters.This doesn't happen on any other computer.
View 12 Replies View RelatedI've recently moved house and decided to go with Virgin as my ISP. I was able to connect one laptop (running Windows 7), with no hassle, to the internet just fine, however, I've tried connected another laptop (running Windows Vista) and can connect to my router but cannot connect to the internet and it's telling me it cannot identify the network =/ I also can't connect to the internet if I use my ethernet cable. I phoned up tech support also and they recommended I update my drivers, but Windows is telling me I have the most up to date driver for my network adapter.
View 19 Replies View RelatedI am recieving full wireless signal stregth and says that i am connected but my computer cant identify the network and wont connect to the internet. I have tried everything the diagnosis has said to try but non of it has worked thus far.
View 1 Replies View RelatedI use windows7. Previously i had a normal internet connection (i use wireless) and few days ago my computer cant identify my network. It shows that im connected but it cant identyfy.
View 1 Replies View RelatedHow can I identify loop or virus in the network? is there any command to find out these ?
View 2 Replies View RelatedI have a Toshiba Satellite laptop that I can't get to identify my wireless network. I can get online using an ethernet connection to the router, but it can't identify the network and the wireless connection gives me just Local Only. I have another laptop that can connect to the router, and the Toshiba can connect to other networks. For whatever reason, the issue only appears when this laptop attempts to connect to this router. I've looked for suggested fixes, but none of the following have worked: Disabling firewall Deleting network adapters and having windows install them again Confirming that dynamic IP address is assigned Confirming that DCHP is enabled Running KB928233 I've tried every suggested fix I could find and nothing has worked. I have a Clear Home modem connecting to a Toshiba Satellite A215 with a Atheros AR5007EG Wireless Network Adapter and Realtek RTL8101E Family PCI-E Fast Ethernet NIC.
System Info Utility version 1.0.0.1
OS Version: Microsoft Windows Vista Home Premium , Service Pack 2, 32 bit
Processor: AMD Turion(tm) 64 X2 Mobile Technology TL-60, x64 Family 15 Model 104 Stepping 2
Processor Count: 2
RAM: 1917 Mb
Graphics Card: ATI Radeon X1200, 128 Mb
Hard Drives: C: Total - 151125 MB, Free - 84247 MB;
Motherboard: TOSHIBA, IALAA, 1.00, 0123456789AB
Antivirus: Trend Micro AntiVirus, Updated and Enabled
Mid-day Thursday one of the laptops in my office suddenly was unable to identify the wireless network.
I have had this problem in the past with the other Dell laptop. Both are Windows 7. Tried uninstalling the adapter 4 times now. Changed SSIDs on my network. Added a SSID. Nothing works.
I am able to identify and get online if I put the IP address and DNS server in. Nothing I do lets it use DHCP.
C:UsersCheryl>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Cheryl-Laptop
[Code]......
I'm running windows7 and I have problem with my network. When I connect to the router it can detect the router but it cannot identified the network and get limited connectivity. I have tried using wireless and LAN connection and it result the same problem.
View 1 Replies View RelatedI've used a newly purchased laptop, Acer Aspire 5733Z-4614 to connect to wireless networks before, including the network I'm currently on (/w another laptop), however, recently it has been unable to go through to the internet, but does successfully connect to the network. The encryption seems to be OK, since both laptops are using the same WPA2-Personal AES, and this (currently connected) laptop does just fine. I've read through a few other articles on this site but haven't been able to pinpoint the problem. To my knowledge I have not changed any settings since it has worked correctly.
[code]...
I'm having trouble connecting my desktop to my home network. It was working fine last night, got home from work and voila, can't connect to my router anymore. My setup is cable modem, router, desktop via ethernet to the router, laptop. The laptop, which I am using right now connects just fine wirelessly to the router. Nothing has been changed to the desktop, no software installs, no hardware installs, etc.. No malware / viruses were found either. I'm using windows vista sp2 x32.- Power cycling - Firmware updates - Network adapter driver updates - DHCP working fine on router - No MAC address filtering - Also tried static addressing - Restoring factory defaults on router - Desktop restore to last night's restore point ( when it was working ) - All kinds of diagnostics - Ethernet cable testing.
View 5 Replies View RelatedMy laptop normally always works on the wireless network, but every now and then its randomly stopped working and said "identifying network" followed by "could not identify network, unidentified network." When i would troubleshoot it would say stuff about the default gateway and not a valid ip address. THis was fine because it would always just start working on its own in a day or so. However these arnt coming up when i do the troubleshoot this time, and its been over a week and no improvement.Im obviously writing this from the desktop. and the stats below are the desktop stats.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i7 CPU 930 @ 2.80GHz, Intel64 Family 6 Model 26 Stepping 5
Processor Count: 8
RAM: 6135 Mb
Graphics Card: NVIDIA GeForce GTX 465, 1024 Mb
Hard Drives: C: Total - 953766 MB, Free - 437284 MB;
Motherboard: MSI, MSI X58 Pro-E (MS-7522), 3.0, To be filled by O.E.M.
Antivirus: Trend Micro Titanium Maximum Security 2012, Updated: Yes, On-Demand Scanner: Enabled
I bought the modem from clearwire but after a period of time cancel internet because price is going up, i get to retain the modem, I live at campus now and i can get free internet by registin my physical adress and model. How can I identify the physical adress to register it in a new network to continue using the modem and pick up the signal with my modem..
View 1 Replies View RelatedI have an Inspiron 1521 and while I can find and connect to a network easily and quickly; it takes 5 minutes or so for it to really work. My icon says it's "identifying the network". Is there anything I can do to speed up this process?
View 1 Replies View RelatedI have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies View RelatedHow to install a wireless network in home environment?
View 6 Replies View RelatedI am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies View RelatedI have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies View RelatedI have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies View RelatedI have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies View RelatedI'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies View RelatedI have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things
View 8 Replies View RelatedEvery time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.
View 6 Replies View RelatedMy Set up at home is as follows: [code] Now according to what I have read I should be able to set the subnet on .2.0 network to a subnet of 254 and this gives me 512 Hosts I believe however my question at this point is how to route between 192.168.1.0 and 192.168.2.0.Or when I set the subnet .254 does the router just route it automatically.I would still set the subnet mask on both networks to 254 correct? I believe I can only use 192.168.0.1 to 192.168.1.255 w/.254 subnet mask. However I already have some servers that are configured with applications (On the 192.168.2.0 network) that I do not want to change ips on because it would be a pain to reconfigure so, my other question is other than using .252 to extend it to 192.168.0.1 to 192.168.3.255, (I need the 192.168.2.0) is there anything I can do? Like use 192.168.1.0 with subnet mask of 255.255.254.0 to get the 192.168.2.0 network? The reason I asked is I was using a subnet calculator to try and figure this out but every time I put in 192.168.1.0 with .254 subnet mask it changed the ip to 192.168.0.1 to 192. 168. 1. 255.I would really like to use the netgear only. The way I have it now is not working I am able to ping the internet from the 192.168.1.0 network but I can't ping from 192.168.2.0 network to the 192.168.1.0 network.
View 2 Replies View Relatedwant to setup a small home network of about 10 PC's.I want them to share the internet connection of 25mbps.I also want Printer Sharing.
View 2 Replies View RelatedAt the moment I have my home network (192.168.0.0/24) like as below (all connect using straight cables): [code] My Cisco lab equipment are in the basement all connecting to an access server which at the moment is plugged into Switch3-dumb (along with a printer & NAS).What I'm thinking is to replace the Switch3-dumb with a 3550 I'll be picking up later this week.Then using this to do as the Switch3-dumb did maybe by creating a native 'vlan 192' & putting it into a gig interface which will connect to the network using the straight cable, also putting the printer & NAS into the same vlan.This will hopefully still give me connectivity throughout.Then when required I'll like to use the 3550 with the rest of my Cisco equipment for setting up different labs (segmenting them from the home network by using different vlans etc.One of my reasons to implement the 3550 into the home network is to be able to play about on a regular basis (port monitor, traffic stats, etc).
View 2 Replies View RelatedMy Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again
View 3 Replies View RelatedFollowing are my components at hand.
1. My super awesome desktop with the regular gigabit, on board lan card (on Win7).
2. A laptop, with wireless connectivity (again on Win7).
3. A modem, UTStarcom WA3002G4 with an internet connection from BSNL.The modem is a wireless modem.
I want to be able to connect the laptop and the desktop in a single LAN connection, so that
i)I may play NFS Most Wanted on both the laptop and desktop through the LAN play.
ii) I may share files and folders, fast and without any hassles.
After trying most things and spending money like water, I still cannot get our home network to be adequate and I am out of options - Tried using two 100MBit/s Netgear routers "bouncing" signal to each other (Wireless Repeating Function). Not ideal as security is small and speed was slow (<10MBit/s) but at least it worked. However these routers had to get pensioned off when we put gigabit ethernet in the office - and the Netgear replacements (a) still have the security limitations with wireless repeating, (b) anyway see to do a worse job of repeating. Tried buying Netgear directional high-gain antennas and directing the signal point to point to a second router - didn't work at all. Tried Powerline (this was in 2008). It sort-of worked but was unreliable and dog slow. I think this is probably not worked by the fact that this building is OLD, most of the wiring is OLD, and anyway the electrical path would take the signal from the 4th floor, down some very old wiring to the ground floor, across a very old switchboard, and back up to the second floor... it's not quite the same as a modern house with modern wiring. Most recently tried using Netgear's Wireless Network Extender. Again, it sort of works, but it's NOT fast at all. In addition there are times when some of our computers using the extension segment of the network are unable to connect - they can still see 3-4 bars of signal, but they cannot get on the network. Appears to be an issue relating to gateway, or DNS, not sure. But I would say about 1 day in 3, when I come home, my wife tells me that the "internet is off".
View 4 Replies View Related