Does anyone Know if I can use Siemens cat6 jacks with any other face plate? I can get all Siemens stuff from work, but am not overly fond of how their face plates look to put them all over my house.
View 1 Replies
Our house has a cat5 line that runs from downstairs, around the outside of the house to an upstairs office. We are consolidating all the outlets that are randomly spread around the walls. The cat5 cable is about 6 inches too short to reach the new box so we figured we might as well run a new cat6 line. (I think we can make the run 20 feet shorter so that's a bonus.)The cat5 line has 2 jacks wired in series at either end. Everything I've read says cat6 is much more touchy and you should only expose the minimal amount of wire from the sheathing and don't untwist the pairs more than necessary. Can I put two jacks on each end of the cat6?
View 4 Replies View RelatedWiring my house for Cat6 very soon. I already have most of the architecture decided on (except the decision of whether or not to use a patch panel, but that's another story). However, the office layout is giving me problems.
See, I plan to rent out my house some years down the road, as work will inevitably force me to relocate sooner or later. I know that *I* would want the ethernet ports on the North side of the office, but I can conceivably see somebody else needing them on the South side of the office. Cords running across the room are a pet peeve of mine, so that's out.
Instead of placing the jacks on just one side of the room, I'd prefer to put a jack on BOTH sides of the room, for each line. Like how you used to find two RJ11 phone jacks on the same landline. (note: only one pair of jacks would be used at a time). Is this easily possible with Cat6?
I have a N+ wireless router model F5D82335 and have lost my owners manual. I can't find online info on what the face lights mean. Currently the wireless yellow light flashes about ten times then pauses and flashes again. I have no issues with being able to connect.
View 1 Replies View RelatedNot sure why Cisco is shipping like this? It is a pain to mount them. Earlier we had option to slide out the Secuirty hasp.
View 1 Replies View RelatedIs there a Cisco wall-plate model? Something similar to HP E-MSM317 and Ruckus 7025? I had look on the web but couldn't find anything.
View 3 Replies View RelatedI converted my old telephone wiring (Cat5e wire) to Ethernet by adding keystone jacks and then tied all the rooms together. I test every room for continuity with a LAN tester and everything showed up OK. I then plug my Ethernet in one of the keystone jack and check for internet in every room with my laptop received no connection. I connect the same cable to my laptop and everything works fine
View 18 Replies View RelatedI am trying to wire cat 5 jacks into my walls and none of the jacks work. I have tried with multiple jacks and experimented with different wiring configurations but they still don't work. I know the wire I am working with is good because it had a male connector on it and I connected it to my laptop before I started wiring the jack and it worked.
View 3 Replies View Relatedthe internet is so poor I usually lose the signal, since it has to go through walls and a bunch of trees. My question is can I use the phone jacks in the wall to set up a second router or something to increase it. Or what is the best way to increase the power and strength. What do I need and how do I do it. My fathers router is under verizon vios. I plan on getting and xbox 360 with live capability and need good internet for that
View 2 Replies View RelatedBesides MAC address filtering, is there another good / easier way to keep visiting laptops etc from plugging in a CAT cable and accessing a LAN protected by a perimeter firewall?
View 3 Replies View RelatedBesides MAC address filtering, is there another good / easier way to keep visiting laptops etc from plugging in a CAT cable and accessing a LAN protected by a perimeter firewall?
View 1 Replies View RelatedIs there an easier way to connect an RJ45 connector to a Cat5 cable, rather than the traditional method of lining up the wires by hand, inserting them in the right order into the jack, and then crimping it? It just seems like it would be very tedious if you had to do this A LOT, and I've had a good bit of practice. I saw that they make "EZ RJ45" jacks.. but do they make anything else that can make it easier? I'm asking out of curiosity, and not necessity. I have no problem wiring them, but it's just something that I hate to do (I think a lot of people would agree that it's not the most fun thing to do in the world of networking).
View 13 Replies View RelatedI need to have some (maybe four) virtual network interfaces, one face of them connected to my laptop and another face bridged to one of my physical network interfaces.How can i do that?Ive tried VirtNet and Microsoft Loopback Adapter but no success.
View 1 Replies View Relatedwhere i can get driver for siemens gigaset 504 agu? Need driver software.
View 1 Replies View RelatedMy friend recently let me have his Seimens Gigaset SE567 modem which i needed cause it has a router but as soon as i switched it with my old router which is a Westell 6100f,the internet light wont show up ..so i contacted verizon and they said that there service is plug and play type of service so i am lost on what to do ..i looked around the forums and i got close by going to the browser and typing the IP but from there i am stuck ..i don't know how to set up any thing in the configurations.
View 2 Replies View RelatedI'm thinking of making a security system for my house (and possibly selling and setting up for others) based off usb 1080p webcams. I read online the max length of a usb cable is 5m before you need a hub to act like a repeater. Could I simply buy a cat6 (or 7) cable, splice the usb into it, and then unsplice at the computer as a workaround?
View 8 Replies View Relatedwlan is not working vth siemens gigaset se568 modem.when trying to connect wlan then the indicator of wlan turns on and suddenlt it goes to off
View 1 Replies View RelatedI already connected the wires to my computer and I already switch on the power of the GIGASET , unfortunately I still cannot connect to the internet using my PSP and LAPTOP
View 3 Replies View RelatedHow can I access this router?
View 2 Replies View RelatedHow can I get a driver for this wireless modem? My netgear failed completely. I am using a neighbour's connection to get on to the internet, and tried to download a driver, but every link I could find wanted to search my computer for the hardware. Ridiculous! I need a driver to make it work, and if I plug the Siemens in I lose the connection to get a driver.
View 1 Replies View RelatedI want to update my router as it currently provides poor wireless connectivity. My current router is a Siemens Gigaset SE587 wlan dsl. This supports a 802.11g frequency, though I'd like to update my home network to 802.11n. My concern is this, is it worth buying a new router/hub that supports this frequency if the other devices in my home are still using 802.11g, i.e. Xbox 360, Nintendo Wii, Laptop etc. Would it be worth instead to purchase a homeplug kit instead?
View 3 Replies View RelatedI have the same problem connecting my sl2-141 siemens router to thomphson cable modem. What I have heard is that the router can be hacked throw the profile.xml file,one can change the connecting type to "dynamic ip",what i need to know is what entry in the profile.xml file t5o change to what value.
View 6 Replies View RelatedIn my coy two desktop are connected to home network and one network printer is installed in our complax so my problem is in one desktop two NIC card are installed in other desktop one NIC Card are installed and no any connectivity through Switch.
so my problem is i connected to a desktop by two NIC card desktop via cat6 cable to other words connected to lan by two NIC card but my desktop can not connect to the Network printer.
i want to know what is exactly the difference between cat6a and cat6+??
View 7 Replies View RelatedWhenever it comes time to terminate Cat6 lines into an RJ-45 connector, there is an expected way of lining up the colors in each end. This differs somewhat between Cat5 and Cat6 but the principle remains the same: there is a standard order in which to feed the wires into the connector.
My question is, why is this order used? Is there a specific reason why it is done this way? The way I see it, since all 8 wires inside the cable are the same, it shouldn't matter which order you use, as long as it is the same on both ends...
siemens se568 router installed. Net is fine in PC.but not getting the wifi connection in i fone,despite wifi icon
View 2 Replies View RelatedI'm trying to hook up a Siemens Speedstream 4100 and a Linksys E2500. The internet works fine when I plug the modem directly into the computer. When I try to run it through the router, though, the router install appears to work right but I get a message saying that my internet connection might not be working. I power-cycled everything - unplugged all the cords and waited 20 minutes before restarting. It sounds like putting my modem in bridge mode might be the move? When I type in 192.168.0.1, I get a message that says "Server says: Linksys E2500." It also wants login information, and I'm not sure what that would be.
View 4 Replies View RelatedI cannot install driver for Nokia Siemens Network c2110. when try it show error message then followed by another message showing" required administrative right....." where as this connetion works on laptop and that same file installed into another computer.
View 1 Replies View RelatedI have an esprimo fujitsu seimens laptop and have just purchased a kodak esp 3.2s printer. I have a belkin router and am unable to install the printer, it is not recognising the router.
View -1 Replies View RelatedI have a modem router (TP-Link TD-W8961ND) connected to the internet and working fine. It is broadcasting a wireless network and that too works fine.
I have a second modem router (Siemens SL2-141) functioning as an extender. It is wired to the first router and broadcasting a wireless network with the same SSID, same security, but on a different channel. DHCP and UPnP are disabled on the second router. My i Pad, iPhone, and Win7-based Think Pad are all able to move between the two networks with no problems.
We also have a Win XP SP2 Net book. When in proximity to Router1, this machine accesses the LAN and Internet with no problems. As soon as it gets closer to Router2, it picks up the signal and shows an "Excellent"/"Strong" connection but it can no longer see the internet. It can see Router2's config page and the other machines on the network but it cannot get past the router to the internet.
I have done similar with cat5e in the past, but only operating at 100mb/s. The gigabit stuff I have done so far has had the power in a separate stud cavity.My structured wiring project will be installed in one stud cavity in the soon to be new home office. Not exactly using a structured wiring cabinet, but rather using a 7u wall mount relay rack bracket. The cabling will be entering using 2 separate header penetrations. One existing just inside on the right side of the stud cavity carries 110V 12/2 romex to a stud attached box / recepticle. The other side gets the new penetration, a minimum of 12" away. That's the one that the ethernet cable will pass through. The cable runs will run through the wall and through a brush plate, and then to the patch panel.
The Cat6 cable is UTP, and is marked for in wall use. This is the stuff with the spline if that matters.The romex, by code MUST be attached to the stud, and it is, the cat6 on the other hand is allowed to be loose in the wall. I do not plan on having enough slack in the wall for the cat6 to ever get closer than 8" from the romex, and no closer than 10" from the electrical box.Is that separation sufficient to avoid inductive noise on the ethernet cables? Like I said, I have done similar with Cat5e and no problems ever, but only attached to 10/100 networks. I can change stud cavities, but would rather stick with the one so that my ethernet, and power both can enter the rack cleanly.
Am running Cat6 cable to my cellar. I plan to run a face plate in the walls of all rooms where there will be an ethernet connection. Originally when I did this in a previous house I wired two rooms together i.e. a face plate in one room and the other end a face plate. I did a cross over cable for this so when connecting anything at the other end it would talk to the device in the other room i.e. room A NAS straight through to face plate, room B PS3 straight through to face plate for example.However as I will be connecting multiple rooms together in to a patch panel then switch / router how will this then work? For all rooms where there is face plate do I crossover all cable to the patch panel or straight through? If straight through to the patch are my patch leads then cross overs to the switch?
View 2 Replies View Relatedhow to reset nokia siemens 1600 modem as i have forgotten its username & password which i changed?
View 1 Replies View Related
