I want to know how to have a double SSID but it's forbidden to have a wireless interruption with the wep which is on my cisco aironet 1242AG. I need to have wpa2 in addition of the wep.
View 2 RepliesI am in the process of moving our office and part of the task involves relocating our existing wireless access points. They are all 1242AG's running the c1240-k9w7-mx.124-10b.JDA3 IOS. I would like to change the security on the access points to WPA 2 but that selection is not available. I think upgrading the IOS will solve this problem but I am not sure. So I guess I have two questions:
1) Does this Cisco model support WPA 2 ?
2) If so what IOS do I need to load to make WPA 2 available?
Before I purchased the E3200 yesterday, I contacted Cisco Sales support and asked specific question about SNMP support on E3200. I was told that E3200 does supports SNMP.. However, I do not find any setup / nor any documentation on how to. Does E3200 supports SNMP? I would like to monitor my router using SNMP traps.
View 4 Replies View RelatedI have inherited a Cisco VPN 3005 and need to configure an interesting scenario:
2 LAN-2-LAN tunnels: 1 required an outside IP and has an existing static NAT of 192.168.1.1 -> 12.2.1.1 for 0.0.0.0 as the destination.I now have a need to created a new NAT for 192.168.1.1 to translate to 10.99.1.1 for destination of 13.3.1.1, 14.3.1.1 and 15.3.1.1.
Is it possible to have the above scenario, or even NAT 12.2.1.1 from the first NAT back to 10.99.1.1??
I have two RFC1918 domains I wish to connect, can I use double NAT with PAT so that each domain is represented as one single ip address with each session a port of that address-
The link is a private point to point link with a /32 mask so could I use this as the PAT address ?
Facing a problem of double multicast on one of our cisco 3750 switch. On checking with sniffer it was found that out of double packet’s one packet is having source mac-address of vlan and another packet is having a source mac-address of switch base mac-address.
View 3 Replies View RelatedI am setting up a new ASA running 8.3 and I am having problems with configuring double NATs.
Here is the thing I am trying to solve:
Original Packet
SRC: 1.1.1.1
DST: 1.1.1.10
After it hits the firewall and it comes out on the outside interface I want this:
SRC: 2.2.2.1
DST: 2.2.2.10
Now when I set this up the way I did in 8.0(4) it just ain't working.
All the NAT examples I can find are simple NATs, I have not been able to find an example of a SRC and DST NAT.
i bought me a router so that me and a few other friends could play to star craft 2, but i would like to know that if i could play an LAN with NO internet on it?
View 2 Replies View RelatedI have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt.As u know the connections work separately by default!! (I use Windows 7 64bit)Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 2 Replies View RelatedWe just upgraded our Sg300 series switches to the new IOS so we can get CLI access. The upgrade went fine but it seems we have two login prompts, the first being completely unnecessary as you can just hit return to get by it. IE here is the progression:
1. Connect SSH
2. Receive a "login:" prompt. Anything can be entered here, including just return
3. Login banner is displayed
4. Username Prompt is then displayed. Valid username required
5. Password Prompt displayed - Valid password required
6. Now at CLI 1. Connect SSH
I am trying to get rid of that first login prompt (IE Step 2) as it is causing issues with our configuration software. I have tried every line and authentication command I can think of, the only thing that gets rid of it is using none authentication which obviously we can't stay with. how did you get around it?
is it to increaze the broadbandwith by using a double usb-modem dial-up ...i know tha we can use double connection, but not in real time...
View 8 Replies View RelatedI have 2 LANs in my own PC & 2 Routers (TP-Link WR941N each) with 2 internet accounts (512Kbps each) connected to the same ISP signal & company using NanoStation 5 from ubnt. As u know the connections work separately by default!! (I use Windows 7 64bit) Can I merge them to get double speed (download/upload simultaneously) using reg edit or special software or method?
View 3 Replies View RelatedThis is my Cisco LAB environment used for study but also in production for daily use. I am trying to setup a double-NAT network with just one IP from my ISP through the ASA & 3825 going to (2) end nodes and multiple ports for port forwarding. It is currently working but only as simple PAT and I cannot initiate FTP from the outside. removing the router, but this is my study LAB and it's a bit unconventional for learning purposes. I attached the diagram and need parts of the config.
View 14 Replies View RelatedI'm currently switching from a certain internet provider to another and I'm forced to get another router. What I wanted to do is since the initial router has to be on the first floor, I'd like to have the second one on the top floor closer to my computer whereas they would share a dedicated connection between each other wirelessly so it would make my connection faster rather than just having my pc connect directly wirelessly to the initial router on the first floor. Is that possible?
View 4 Replies View RelatedI only have access to rather slow connections (256 Kbps). But since I have two lines and two modems, I was wondering if I could bond them together and make a faster one. My main modem is a Lynksys WAG120N Wireless-N ADSL2+ Modem Router, which as you can see is also in charge of both wired and wireless networks at my place. The second one is an older D-Link ADSL modem (JUST modem).Since I have an extra LAN port on my Lynksys modem, I want to know if and how I can connect the second modem, and combine the two rates.
View 2 Replies View RelatedI'm new to networking (at least at this level) and need some guidance. First, I have an Actiontec MI424WR (Rev. F) Coax Verizon Fios modem that I use as my home networking wireless router. From a LAN port on that I've connected a cable to the WAN port on my DIR-655 which acts as my gigabit office hard wire/wireless router. I need to keep the home network and the office network separate.All of my computers are Windows, either 7, Vista or XP.Connected to my Dir-655 on the office network are 2 wireless computers, a printer, an IOMEGA 1TB Home Personal Cloud NAS HDD, plus 2 desktop computers.The DIR-655 is set with a static IP address matching the range of the Actiontec. The DIR-655 is set for DHCP for the devices on the network (although 2 of the computers have static IP address).
When the DIR-655 had a Dynamic IP address set by the Actiontec, the IOMEGA NAS HDD kept losing connection with all the devices on the network. Only after I set the DIR-655 to static IP did that stop and everybody started to play nice. I'm not sure why that would make a difference, but it did.But regardless of whether it is set to dynamic or static, no computer on the network or program, even third party programs, can connect to ANY of the time servers out there... and I mean any of them. I've tried at least 20 or more of the standard and not so standard ones. The DIR-655's time is off, and it is set to get time automatically. None of my computers, or my IOMEGA NAS, can access time. The Actiontec, though, seems to be set correctly.Everything connects to the internet just fine. Web, email, auto product upgrades. Fine. So far it's just the time server thing which troubles.I done everything I know how to do to enable Port Forwarding through both routers for NTP > UDP 123 since that is the standard port for the Network Time Protocol, but I could have easily screwed that up.
On our 6504 - 12.2(33)SXH, we currently have a single connection to our ISP (GI1/1) and want to add another connection (GI1/2) Is there a way to bond the two connections to form a single connection (a single pipe) to double the throughput?
View 3 Replies View RelatedI would just like to double-check a point with the forum on licensing on 4710 Appliance.If with version 4.2 and above 2Gbps Bandwidth licence is required, the output of the sho license status should be?
View 1 Replies View RelatedI've a network with 28 computers and 2 servers. Each server have a double Gbit port configured in Load Balancing & Fail Over.Now, I want to buy two Cisco's Switch SG 200-26 and I would know the best way to connect them and if it's possible to interconnect them with more than one cable to share the trafic.
1. Is this following solution a good one (does the link between swhitches will work when computers will access to servers) ?
2. Is this next solution possible ?
I have an HP C5280 printer running wirelessly via a TP Link wireless print server and D Link Di 624 wireless router. I can print successfully from either my desktop (which is connected direct to the D Link router) or either of my laptops (wireless). However, when I select the double-sided print option I get a print error message after re-inserting the odd number pages to print the other side of the paper and then click 'continue'.Could I resolve this by connecting the printer both direct to the desktop using USB AND leaving it connected via the wireless TP Link print server? This would enable me to print double-sided from my desktop (as I did before when the printer was only connected via the USB desktop port).
View 1 Replies View RelatedI'm suffering from an annoying problem with my E4200 router. I have a DSL connection. I have my DSL modem in bridge mode and I have my router set up to sign into my ISP's PPPoE to avoid double-routing. This set up worked marvelously with my previous WRT54G and WRT610N routers.Now the E4200 signs me out of PPPoE every ten minutes or so. I have the connection setting on "Keep Alive" but it seems to be dropping the connection regularly. I took the router back and was given a replacement. The new router is doing the same exact thing and now I am beyond the 30 day return limit so I'm stuck with the E4200. I'm running the latest firmware 1.0.03
I reinstalled the WRT610N and the connection is steady but the WRT610N has its own problems (devices connected via wireless cannot see wired devices and vice-versa). I'd like my new router to actually work properly. I've ruled out errors on my end and given that two brand new units of the E4200 generated the same problem I tend to believe it is a design error.
I'm looking to make a few adjustments to out wireless network and need to change the RF channels on a few APs.I've logged on to NCS went into the AP, an 1142N, then the Radio 802.11 b/g/n and changed the RF channel under custom.Once I pressed the save button the channel reverts back to its original channel. I've also tried this on a 1242AG the same thing happens. I then went to the controller and tried to change the RF channel there and it took the change. I pressed apply logged out went back to NCS made the change under custom and again it reverted back after I pressed the save button. I went back into the controller and the channel had also reverted back even thought it gave the impression it took the changel.
View 1 Replies View RelatedCurrently have a WLC4402 installed with 21 AP's reporting to it. The controller is running at LWAPP3 with version 3.2.116.21. The WLC was purchased prior to Cisco buying Air-e-space, and has a 36 AP license. When attempting to install additional 1242AG-A-K9 ap's, the controller will not acknowledge them. I have verified the LAN confiuration as correct, and working properly.
View 9 Replies View RelatedI've recently obtained a Cisco Aironet 1242AG WAP. I do realize this is not a standalone router. I would like to use it as an extension of my current router. So right now, the status light is alternating colors. If I understand this correctly, it cannot find the controller. I cannot telnet into it, or use the web broswer interface. They both say the connection is not available. However, when I check my DHCP table from my router, I see that an IP has been assigned to the MAC for the WAP. I've tried doing a factory reset by holding MODE before I plug in the power, and waiting until it turns amber. After a few minutes and going through a few LED changes, it goes back to continuosly alternating colors.
View 14 Replies View RelatedI am struggling since many weeks for an issue in my Wireless infrastructure.
I have an LAP (1242AG) in one B site that I would like to attach (in H-REAP mode) to the WLC of site A(5508 v6.0.199.4). The topology is as follows:
MPLS - Site A - MAN - Site B.
When Site A is fully connected, all is fine, my AP of site B can successfully join the WLC of site A.
However, when the WAN interface of the router of site A is disconnected, the AP cannot associate successfully to the WLC. For us, it does not make any sense during that time, the AP of site B can successfully ping the WLC of site A and the traceroutes show the exact same path.
I took some debug on the AP and the WLC while the AP's was trying to associate to the WLC (when the WAN link of Site A was disconnected) and also when the AP could successfuly join the WLC when the WAN link of site A was reconnected.
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies View Relatedis this possible, i need to convert a 1242AG Autonomous back and forth this weekend to use for a quick project for testing. i need to do: take the AP into LWAPP mode (i know how to do this with the aironet utility) take the ap from LWAPP back into a AP mode so i can use it as my access point again. [code]
View 3 Replies View RelatedI need to bridge from our office to our shop that is around 800 feet away. Here are the Details
I need the 2.4 ghz antenna for client access (Iphones are not compatiable with 802.11a) The locations are 800 feet away but are line of sight. I need to use the 5ghz antenna for the bridge i have 2 aironet 1242ag's I have 2 2.4 ghz AIR-ANT3213 antennas (planned for client access) I have 2 2.4 ghz AIR-ANT2506 (maybe useless for this)
My problem is that the range of all the listed 5 ghz antennas. None that i can find will bridge 54mb over the 5ghz radio for greater than 170ft
The closest that i can find is AIR-ANT5195. If i put these on both sides and it is outdoors line of sight, will the best i can hope for is functioning and 6mb
Are there options on 5ghz that i am missing.
I need a temporary additional broadband connection at home and I was thinking about a bt openzone hotspot connection...
I have a cisco 1242AG access point which can do bridge mode. The BT openzone thing requires a username and password. Is it possible to connect the 1242 in bridge mode to bt openzone?
What would be the ramnifactions of using AIR-1242AG-A-K9 (g radios only: no b clients) and AIR-LAP1231G-AK9 (g radios: only no b clients) with AIR- ANT1728 (non diversity antennas) on the WLAN. Some of the APs 1242/ 1231 will be with in line of site of each other.
View 1 Replies View RelatedI am new to cisco products and I am trying to setup an aironet 1242ag. I have figured out the ip given to it but, cannot access it with a browser.
View 6 Replies View RelatedMy question is about the maximum possible transmitting power in a Cisco 1242AG-E-K9.I did an update of my AP on a new ios version and since then, the maximum power for me is limited to 17 dbm. I check this within the console and the "show controllers dot11radio0 | include Power:" command. I thought that I had 20dbm before the update, but unfortunately I can't proof this by myself because I have no AP left with the old firmware.
Is it possible that the upgrade did this? I read about the regulatory domains for the transmitting power. I live in Switzerland, so I thought I could use 100mW if I want to. I read it's not possible to use the 100mW at each speed but I think I should stull be able to select the 20dbm/100mW or am I missing something?
I have an issue with a loss of connectivity after 10-15 seconds. I have a Cisco WLC 2504 controlling a Cisco 1242AG AP. The following is the topology.
Wireless Client -> 1242AG (AP) -> Port 3 WLC 2504 -> Port 1 WLC 2504 goes to fa0/2 on 3560. Port fa0/1 goes to ASA5505 (Inside)
All devices are on VLAN 10 10.50.1.0/24. AP is getting DHCP just fine and is associating with the WLC just fine. I connect my laptop to it and it connects just fine.
I then ping the gateway (ASA) 10.50.1.1 or the layer 3 interface on the switch 10.50.1.7 and it is fine for about 10 seconds, then it just dies then comes back in a few minutes and then goes away again. I have looked for duplicate IP's and can find none in any arp table.
It I just ping the controller 10.50.1.20 it is completely stable. I have moved the WLC directly off the ASA5505, moved the switch port, changed cables and the problem follows. I have even moved the AP to be directly off the switch instead of the WLC and the problem still occurs.