Cisco AAA/Identity/Nac :: ACS 5.3 - Get Downgrade To 5.2?

Jul 24, 2012

I want to downgrade an acs acs 5.3 to 5.2 - I have looked through the documentation, but somehow I fail to find the exact commands for the downgrade.
 
Previously I just used the recovery cd to reinstall the image, but  it must be possible to do a downgrade without loosing all the configuration.

View 5 Replies


ADVERTISEMENT

Cisco AAA/Identity/Nac :: Downgrade ACS 5 - How To Do

Jul 24, 2012

I want to downgrade an acs acs 5.3 to 5.2. I have looked through the documentation, but somehow I fail to find the exact commands for the downgrade.Previously I just used the recovery cd to reinstall the image, but  it must be possible to do a downgrade without loosing all the configuration.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: ACS 1121 Appliance Downgrade To 4.2.0.124

May 2, 2011

Newly shipped cisco  ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
 
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With  5.1 SW And Base license

[code]....

View 2 Replies View Related

Cisco :: Lms 4.1 To 4.0 Downgrade?

Feb 12, 2012

I have installed LMS 4.1 but due to license issue i want to downgrade to 4.0 , is there any way to do that ? .

View 4 Replies View Related

Cisco Wireless :: Downgrade WLC 7.2.103.0 To 7.0.235.3?

Dec 22, 2012

i have 2504 with software 7.2.103.0 and i want to downgrade to version 7.0.235.3 , but i face problem after the TFTP Transfer complete and display  this erorr messagges:

- Sanity check failed on file. The file was not downloaded completely!

-  TFTP Failure while storing in flash!

i will attache file contains " debuge transfer trace enable " while i transfer the software.

View 10 Replies View Related

Downgrade Cisco Unity Express?

Nov 13, 2011

I managed to get an AIM-CUE for my 2801 router. I upgraded from version 3 to version 7.1.5. then realised I can't licence it without buying mailbox licences from Cisco (working on a budget for a lab) I tired to downgrade but I get the error

View 1 Replies View Related

Cisco VPN :: Asa 5520 8.4 And ASDM 6.4 Downgrade

Feb 23, 2012

We are running ASA5520 with version 8.4(2)8 software and ASDM 6.4(5)205.We have noticed the following problems:When having more than 30 IPSec,sessions connected, the log fills up with errors "System is low on free memory blocks of size...", When filtering by "AnyConnect Client" in "Monitoring > VPN > VPN Statistics > Sessions" the values "Bytes Tx / Bytes Rx" column is presented in one line ie. "8450198968129194". Seems to be missing a <cr><lf>,When uploading a new CSD-image (via ASDM) all configuration för GPO, CP, DAP seems to dissapear, though, the config seems ok when looking at a sh run. Also, the newly updated csd-image doesn't show i ASDM.

View 2 Replies View Related

Cisco Wireless :: 2504 - WLC 7.4.100.0 Downgrade

Mar 13, 2013

Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
 
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?

View 5 Replies View Related

Cisco Wireless :: Software Downgrade On 2106

Mar 18, 2013

I had a 2106 running 4.x software. It was upgraded to 7.x but will not read the config. How to downgrade the software?

View 4 Replies View Related

Cisco Wireless :: 8500 - Code Downgrade From 7.4 To 7.0

Jun 11, 2013

Working on a project consolidating all controllers to a single 8500 controller with a standby. Moved an AP over to test the process and everything worked fine. Took a little longer than I thought it would, but given the design with new flexconnect abilities, the creation of AP groups well you know.
 
I get the AP over and one of my ssids doesnt work because the key is different, so gotta move the AP back over to resolve production issues.
 
when downgrading from 7.4 to 7.0?

View 6 Replies View Related

Cisco VPN :: How To Downgrade To 2.5.3055 From 3.0.08057 On Mac OS 10.7.5 Lion

Dec 3, 2012

I'm using the Cisco AnyConnect VPN Client (2.5.3055) to connect to a server "A". It has worked fine. Then I tried to connect to the server "B" from the free university of Berlin and then this installed (3.0.08057) automatically without asking. Connecting to server "A" does not work any more. The error message is: "The AnyConnect package on the secure gateway could not be located. You may be experiencing network connectivity issues. Please try again." So I tried to de-install the client with the shipped uninstaller and installed the previous 2.5 client again. but the Error message is still the same.so which files should I remove/edit to get it working as before. The network is OK, I tried it on a other computer under Windows Vista and there the freshly installed Client works fine. So I guess ther must be some files or configurations from the newer version in the way.

View 0 Replies View Related

D-Link DIR-655 :: 1.35na Firmware Does Not Allow Downgrade

Feb 26, 2011

i just thought i would try 1.35na firmware and i decided i wanted to go back to 1.33na, well you cant  BE FOREWARNED.

i don't know what is the big deal about stopping you from downgrading your firmware that they lock you out of it. it never used to be a problem, pretty sure i could downgrade from 1.34na to other 1.3 firmware.

the reason for allowing people to downgrade is incase the new firmware does not work properlly. not allowing your customers to do this is just asking for trouble not to mention alienating your customers.

at work we downgrade firmware to the firmware that passed our quality tests, it also makes it easier to support them when they are all the same.

1.35 works well so i dont have to buy another router. if it doesn't you can be sure it wont be another dlink thats for sure.

View 3 Replies View Related

D-Link DIR-655 :: Can't Downgrade From Firmware 1.35NA

Jan 12, 2011

I purchased a DIR-655 (A4) a few weeks ago, and was encountering a problem.  I immediately upgraded to 1.35NA after I bought it.  First, the actual problem: With WMM enabled, my internet speeds are very inconsistent.  By that, I mean it will fluctuate between full ISP speed and less than half the speed.  A few seconds at full, a few seconds at half or less, and so on.  Well, when I disable WMM, with everything else the same, the internet speeds suddenly become consistently fast at full speed, but PC-to-PC (LAN-to-LAN) wireless transfers slow down considerably.  So no matter what I do I get a negative result.

Thus, I figured I would try downgrading the firmware to 1.32NA, 1.33NA, or 1.34NA, as I read that it is not possible to downgrade directly to 1.2x.  I thought I would simply troubleshoot the problem myself.  Unfortunately, no matter which firmware I try, except 1.35NA, it gives me a paragraph explanation; something like "This file was either not intended for this router, or it is corrupt.  Your router will not be programmed."  It did allow a reflash of 1.35NA, though.  I downloaded multiple firmwares directly from the D-Link ftp multiple times, using a different router, so the files should not be corrupt.

Is it simply not possible to downgrade once you flash 1.35NA?  For the record, I also tried a few of the workarounds I found on the internet: (1) do a hard reset by holding in the reset button and cycling power for 30 secs. (2) I tried some firmware directly from the German FTP which was supposed to allow a downgrade, but still got the same error as above.  (3) I also tried some Russian firmware and it didn't work either.  I was using a hardwired connection to the router during all attempts to flash.

View 5 Replies View Related

D-Link DIR-655 :: Downgrade From 1.35NA To 1.34WW?

Jan 3, 2011

Today I modified a firmware 1.34WW which is stitched atop 1.35NA ! [URL]

View 11 Replies View Related

Cisco Switching/Routing :: Nexus 7K Downgrade Failure

Feb 2, 2012

After trying to downgrade a Nexus 7K from 5.2.1 to  5.1.5 by updating the boot & kickstart boot statements and reloading, I'm now stuck in an endless cycle of reloading. See below:

Is there a break sequence which will allow me to modify the boot statement back to the original via ROMMON or something similar?

[code]....

View 3 Replies View Related

Cisco Wireless :: Downgrade 3600 Capwap AP To Autonomous

Nov 12, 2012

I have to prepare an 3600 Capwap AP for autonomous functionality!
 
The following image was downloaded: ap3g2-k9w7-tar.152-2.JA
 
The release notes say: Site-Survey Only Mode for 3600, 3500, and 1550 Access Points You can install Cisco IOS Release 15.2(2)JA on Cisco Aironet 3600 and 3500 Series access points and on 1550 series outdoor access points to perform site surveys. This release runs on these access points with limited functionality. You can manually adjust these settings on the site-survey access points:

• Channel on each radio
• Transmit power on each radio
• Enable and disable the radios
• Manually set basic and supported transmit rates
• Enable advertised cell power in beacons to client to enable DTPC for doing active surveys
• Enable and disable SSID broadcast in beacons
• Enable open authentication
 
My Question is: Where can i find a instruction for downgrading an AIR-CAP3602i to Autonomous 3600 AP? Is it complicate to get the AP running, or what do i need for "downgrading"?

View 4 Replies View Related

Cisco Wireless :: Downgrade AIR-LAP1142N-A-K9 LWAPP To Autonomous

Nov 14, 2012

I would like to downgrade Cisco Aironet 1142N to autonomous. But I would like to know is there any way to download the LWAPP IOS before upload the Autonomous IOS ? because I want to upgrade the 1142N from autonomous to LWAPP when I buy a LAN Controller.
 
Is that possible to use that backedup LWAPP IOS when I want to upgrade the Cisco Aironet 1142N autonomous to LWAPP?

View 8 Replies View Related

Cisco VPN :: Downgrade ASA 5505 K9 To K8 And Remove High Encryption

Jul 23, 2011

Is it possible to remove the high encryption (k9) from an Asa and make it into k8 model?

View 1 Replies View Related

Cisco Wireless :: Webinterface Does Not Work After Downgrade Of AIR-LAP1142N-E-K9

Jan 24, 2013

I have downgraded one of our AP1142N-E K9 to Autonomous mode with this image: c1140-k9w7-tar.152-2.JB.tar I have uses cisco's instructions.
 
After successfull installation, I can open the Webinterface, but it shows almost no information. Only Device Type end serialnumber, but nothing more. Also it is not possible to save any configuration.
 
Alternatively I have installed:
c1140-k9w7-tar.124-21a.JA1.tar
 
Same problem. I have tried it with a LAP1252N later. Same problem.

View 2 Replies View Related

Cisco Switching/Routing :: 3750x / How To Downgrade The Microcode

Mar 22, 2012

Since upgrading a 3750x switch stack to version 15, PC's on the network do not get a DHCP lease. The only way to get them to work is disable and re-enable the NIC card.
 
Downgrading the IOS does not downgrade the microcode on the switches.Is there anyway to downgrade the microcode?

View 3 Replies View Related

Linksys Wireless Router :: EA6500 Downgrade To 1.1.27?

Dec 13, 2012

provide me with the latest (or one) release of 1.1.27 firmware for the EA6500. I am deeply disappointed in the last firmware upgrade and due to security and sudden lack of certain, or let's say all, functionality in bridge mode I need to downgrade or wait for an upgrade where that's fixed, but most likely not soon, or ever. Where could I find the firmware downgrade.

View 2 Replies View Related

D-Link DIR-655 :: How To Downgrade Back To Stable Version

Dec 25, 2012

I've had the DIR-655 for a few months now, along with a Motorola Surfboard sb6121 DOCSIS 3.0.Modem works fine, the router was working perfectly fine until recently last week.

I have a desktop hardwired and a wireless network going on that I use just for my mobile phone and tablet at times. At first I was having disconnection problems with my wireless, then noticed a neighbor installed a similar router in the area according to my wifi analyzer, so I changed the channels and my wireless started working great. During this process I also did a firmware update and since then I've been receiving some really poor browsing problems, sometimes I'll visit websites like Facebook, or a news website, and it'll say something about the DNS not working, (at this point I'll ping the website and it still pings fine without any loss) so I'll visit the website about 10 minutes later and it works great. I've done extensive research on forums/Google and found it must link up to the new firmware update and something about a DNS relay? My version is:  Hardware Version: B1 Firmware Version: 2.10NA   

In other words, is there a way I can fix this issue from disconnecting without having to downgrade back to the old firmware? Or is this a common issue they'll continue to happen? If I do downgrade, HOW do I downgrade back to the stable version?

View 14 Replies View Related

Linksys Wireless Router :: Getting Downgrade For WRT160nV3?

Jun 21, 2010

I need to downgrade my WRT160n so that it will work with Xbox LIVE again. I've been told by Xbox that the only certified working firmware for my router is 3.0.02.003, But I'm using 3.0.02.004.

View 9 Replies View Related

Linksys Wireless Router :: Possible To Downgrade New EA4500

Oct 20, 2012

I'm in the process of wanting to upgrade my wireless network but I'm not really agreeing to the Cloud Connect, I don't need to have my settings on the internet. I want to manage everything on my own. I've found the following link on the community to be able to put the classic firmware before the cloud connect feature {URL}.
 
My question now is : If  I buy a brand new EA4500, will it still be possible to downgrade to that firmware? No problem with this one? I'm hoping Cisco will continue to publish bug fixing if any to this classic firmware.

View 5 Replies View Related

Cisco Wireless :: Aironet 1250 LWAPP To Autonomous Downgrade?

Aug 25, 2010

upgraded my home AP from Autonomous to Lwapp.  I was an Idiot and thought i was getting an IOS upgrade. I need to revert it back to autonomous and a simple "mode" button reset doesnt work.  I read that I need to Reload original IOS software, but It appears I cant get it without a support contract.  I cant afford servicenet and need to obtain old ios to revert to factory default 12.4(10b)JA1.  Do I need a contract to roll back?  Is there an archive (backup image) of the old IOS that could be still stored on the device.  I didnt back it up and need to obtain the image.

View 5 Replies View Related

Cisco Wireless :: How To Downgrade / Upgrade AIR-LAP1142N-N-K9 To Autonomous Mode

Feb 25, 2012

how to downgrade/upgrade AIR-LAP1142N-N-K9 access point to autonomous mode, because i don't have controller. i'm not able to login to access point as its in Leightweight mode.

View 4 Replies View Related

Cisco Wireless :: Capability To Downgrade AP 1042 From CAPWAP To Autonomous?

Jan 6, 2011

I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.

View 9 Replies View Related

Linksys Wireless Router :: Firmware Downgrade For WRT54G?

Aug 6, 2011

This seems to be an epidemic issue with LinkSys routers (with me myself running in the third such issue).This time, I would require the original firmware of the WRT54 ver. 4 series. Download links in older threads have 404d already.

View 1 Replies View Related

Linksys Wireless Router :: Need To Downgrade WRT54GX2 / Where To Get Firmware

Nov 15, 2006

Last night I upgraded my WRT54GX2 from 1.0.11 to 1.0.14, hoping to resolve some wireless connection issues.  It did not work.  It made something else break.

View 9 Replies View Related

Linksys Wired Router :: BEFSR81 V3.1 Firmware Downgrade?

Feb 20, 2011

I recently updated the firmware on my BEFSR81 v3.1 but would now like to revert to the previous version.
 
Where I can find the earlier version? I've got  2.51.4, build 006 Aug 21 2009 and need the one before.
 
It's not a critical problem, but more of an annoyance. I power everything here off one big switch which goes off overnight. Before the update I'd just switch it all on in the morning and everything would, after a minute or so, work fine. Now, however, I have to power up the router a minute after the modem or it just sits there doing nothing. That's OK when I'm here, but if it's just the wife she can't reach the back to do it.

View 1 Replies View Related

Cisco Switching/Routing :: Blades On Switch 4507R Keeps Blocked After IOS Downgrade

Jan 4, 2011

We made an IOS doBlades on switch 4507R keep block after an IOS downgradewngrade. Before to do it, the equipment comes with blades 1, 2, 3, 4 and we insert "X4418" and "X4548" on blades 5 and 6.[code]
 
After we made an IOS downgrade to a cisco 4507R from "cat4500e-ipbasek9-mz.122-54.SG.bin" to "cat4500e-entservicesk9-mz.122-53.SG2.bin" (comes with a redundancy supervisor blade WS-X45-SUP6L-E) the standby supervisor keep disable.We tried with the command "Switch(config)#boot system flash cat4500e-entservicesk9-mz.122-53.SG2.bin" then save configuration and "reload" comand but the switch runs with the "...54.SG.bin" IOS.
 
We erase the configuration with the command "erase/all non-default", before to apply the reload command insert the "entservicesk9-mz. 122- 53. SG2.bin" using the tftp command.The standby supervisory remains on disable state but the active supervisory runs with the desire IOS. In order to downgrade the IOS to the standby supervisory the active supervisore was removed temporarely (previously the switch was off) to make the standby as active, after that made the same procedure with command "erase/all non-default", "copy tftp://(....122-53.SG2.bin), and "reload" command.
 
The switch was off and re-insert the active supervisory and turn on the switch, after we made the procedure the blade "WS-X4548-RJ45" marks a fault as follows: [code]
 
The blades were reset but don't have access to them.

View 1 Replies View Related

Cisco Wireless :: 3602 Access Points - Power Denied After Downgrade?

Mar 3, 2013

The last shipment of 3602 APs for a customer came with 7.3 software. Controllers are running 7.2.110.0 so APs had to be downgraded. After APs finished downgrading they were still up. When we moved the APs to another controller running 7.2.110.0 they would not come back up. Power was denied at the switch.

View 2 Replies View Related

Cisco Switching/Routing :: Downgrade Firmware On C3750 V2 Switch 24TS-S V07 To 12.2(35) SE5

Apr 10, 2012

Is there a way I can downgrade the firmware on a C3750 v2 switch 24TS-S v07 to 12.2(35) SE5. I have added this new switch to an existing stack but the FW is not compatable. I believe the answer is to upgrade the rest but I cannot afford any down time as they are used to run a CCTV securiy network 24/7. I have included details below to assist with my problem. Switch 4 is the one with a version miss match.

LNB-SWI3750-CTR-01#show verCisco IOS Software, C3750 Software (C3750-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 19:15 by nachenImage text-base: 0x00003000, data-base: 0x01080000
ROM: Bootstrap program is C3750 boot loaderBOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEE4, RELEASE SOFTWARE (fc1)
LNB-SWI3750-CTR-01 uptime is 19 weeks, 3 days, 22 hours, 46 minutesSystem returned to ROM by power-onSystem image file is "flash:c3750-ipbase-mz.122-35.SE5/c3750-ipbase-

[code]....

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved