Cisco :: Add Alarm In LMS 4.0?
Aug 28, 2011I would like add an alarm to LMS when a power supply of some device goes down. For instance, when the power supply fails LMS send an email or something like that.
View 2 Replies
ADVERTISEMENT
Cisco AAA/Identity/Nac :: Secure ACS 5.3 - Receiving An Alarm Notification?
Jul 19, 2012We are using version 5.3 with patch 5. Incremental and full backup are configured but every day we receive an alarm notification.
View 7 Replies View RelatedCisco WAN :: 7206VXR - SMI Card Alarm LED Remains Amber
Aug 25, 2011We are having Cisco 7206VXR with NPEG2 and the IOS c7200p-spservicesk9-mz.124-15.T10.bin.,PA-MC-STM-1SMI is connected to 3rd Slot of the Chassis. The Links terminated on the SMI are working fine and we are not getting any Error Messages on Chassis regarding the this SMI.
But here we have Amber LED Glowing on ALARM LED of the SMI Card.
As per the below Link: URL
This means Loss of Signal/Frame.
##Table 1-5 PA-MC-STM-1 LEDs
#LED Label
#Color
#State
[Code]....
Cisco AAA/Identity/Nac :: ACS 5.2 System Alarm Database Purging
Apr 19, 2012On Cisco ACS 5.2.0.26 Patch 10, I got this system alarm:Incremental backup is not configured. Configuring incremental backup is necessary to make the database purge successful. This will be useful to avoid disk space issues. View database Size is 2.92GB and size it occupies on the harddisk is 2.91GB
In "Monitoring Configuration > System Operations > Data Management > Removal and Backup", we got this information:
Database Purging:If database size exceeds 120 GB, a backup (if configured) and purge will be initiated. If database size exceeds 150 GB, a purge will be initiated.
Could View database size reach 120 GB ?I want to know how long will Cisco ACS works without problem and if I need to hurry to configure purge.
Cisco Switching/Routing :: Catalyst 6509 Interface Alarm?
Jul 10, 2012I am getting alarms on Solarwind indicating interface down on "GigabitEthernet 4/7 - Gi4/d1" and "GigabitEthernet 4/8 - Gi4/d2" from our core switch 6509.Remote login to the switch does not show the interfaces when I do the "sh run" command. Now I am at site trying to identify and diagnose this fault.Looking at the numbering on the switch, it indicates to me the card where these alarms come from is from the 'intrusion dectection module'
how I may login and identify this interfaces and rectify these alarms.
Cisco Switching/Routing :: SW3750 - Voltage Low Alarm In Transceiver
Jun 18, 2012I have the follow error in a SW3750:
%SFF8472-5-THRESHOLD_VIOLATION: Te2/0/1: Voltage low alarm; Operating value: 0.00 V, Threshold value: 3.07 V.
I used the command:
#sho interfaces transceiver
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
[Code]....
Cisco Firewall :: ASA 5510 - Send Only Alarm Of Attack By Email
Apr 12, 2011I have a Cisco asa 5510. I am doing attack a my firewall, using n map. I am seeing in the log the attack but i like that firewall send only alarm of attack by email . I have active email with warning and i received very much email.
I observed that graph show attack, but not ip of attacker, is possible that Cisco asa show the ip too ? The log show scanning with n map but not shunning IP and not send alarm. How i can send alarm ? The graph no show ip, it's possible show it.
Cisco :: WAP 200 Wireless G Access Point Keep Sending Empty Alarm Email
Nov 5, 2012We have a WAP 200 wireless G access point. It worked perfect before. About two weeks agao, we didn't change anything, it began to send empty alarm email every 10 minutes. We upgraded the software to newest version,restarted it several times. But till now, it still keep sending empaty alarm email.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: WLC 5508 - ISE Alarm / Dynamic Authorization Failed For Device
May 30, 2013I am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is referring to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which corresponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
What are the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Run time AAA & prrt-JNI.
I do not want to enable too much debug logs, so what is the specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
Linksys Wireless Router :: WRT120N Gives Audio Alarm (beep) About Every 10 Seconds
Aug 27, 2011Since a few days my WRT120N gives an audio alarm (beep) about every 10 secs. Cannot find how to overcome this or find the root cause. Installed new s/w version. H/W reset. Nothing works.
View 2 Replies View RelatedCisco Switching/Routing :: 5548 - High Current Alarm For Nexus Interface Transceiver
Dec 9, 2012I have a Cisco 5548 Nexus switch with 10Gbase-SR interface transceiver. This interface is connected to Server chasis.
The show interface transceiver details output shows High ++ alarm for Current. Additionally, i am getting output errors on this interface.
Cisco :: Test Fast Roaming Using A Cisco 2100 Series Controller And 2 1140 APs?
Jul 20, 2011I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies View RelatedCisco WAN :: Does Cisco Catalyst 2960-8TC Support Bandwidth Limit Control
Aug 22, 2011We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies View RelatedCisco Wireless :: WLAN Cisco / AP 3502e - How To Get PAT (Product Acceptance Test)
Dec 3, 2011I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedCisco Firewall :: Cisco ASA5510 Unable To Block Unwanted URLs
Jul 12, 2012I have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies View RelatedCisco Switching/Routing :: Configuring COS On 2960G Switches With Non-Cisco Phones
Mar 1, 2012I have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
Cisco Wireless :: Connect Ap-1242AG With Non-cisco Router To Work As Repeater?
Nov 18, 2012is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies View RelatedCisco :: Unable To Understand Cisco Syntax For Nat Rules On 5550
May 1, 2012I am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies View RelatedCisco :: IPSec Tunnel Between Cisco ASA And OpenBSD (Access Enforcer)?
Mar 10, 2011I currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies View RelatedCisco Switching/Routing :: Cisco 3750G Error During POST
Dec 5, 2011I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
Cisco Wireless :: 2 Cisco Aironet 1401 APs Keep Kicking Users Off
Jan 3, 2013I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
Cisco :: CISCO Advanced Firewall On 2911 Router Using CCP?
Dec 29, 2012Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies View RelatedCisco :: How To Connect Laptop To Cisco 3550 Switch
Mar 30, 2011I bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies View RelatedCisco :: PPTP VPN To Pass NAT On Cisco 2921 Router
Apr 14, 2013I am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies View RelatedCisco Switching / Routing :: Cisco 7600 - Support On ACL
Dec 8, 2011I would like to know the IOS which supports :ACL Support for Filtering on TTL Value feature on my Cisco 7600 device. I check on cisco and found the Cisco 12.4T release but this software doesn't fit onto my chasis. which software should I upgrade to on my cisco 7600 to have this feature.
View 5 Replies View RelatedCisco :: Cisco Command For Resetting Password?
Feb 27, 2012I have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies View RelatedCisco :: Way To Connect Cisco Phone Over Network
Jul 19, 2012I finally got the Site to Site Vpn from our corporate to remote site. Is there a way to connect a cisco phone over that network. Since both Voice Vlans are exempt from acl I would imagine all traffic is clear to go accross? and if so I just have to set the phone to our tftp/ccme. Will that work.
View 2 Replies View RelatedCisco :: Privilege Levels On Cisco Routers
Nov 6, 2011I want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies View RelatedCisco WAN :: To Connect Cisco 1800 And HWIC-2T
Dec 27, 2012I have the CISCO 1800 and I have there the HWIC-2T. I have two questions.First is an easy one. I want to replace the HWIC-2T with HWIC-4T but the CISCO 1800 guide and the HWIC-4T guide says that they dont fit together but I inserted the HWIC-4T in to the CISCO 1800 it recognized him with all the 4 Smart Serial ports that it hase. The question is, how can I check if the CISCO 1800 supports the HWIC-4T?Second question is how can I configure one of the Smart Serials in the HWIC-2T/4T to comunicate with the X.25 Protocol? What I have now is at one end CISCO 1800 and at the other end CISCO 2800 and they are comunicating with each other throught one of the Smart Serials they have. I want to connect to each one of then an old pc that comunicate only with X.25 and I want this two computers to comunicate with each other throught those two routers.
View 2 Replies View RelatedCisco :: Prime LMS 4.2 And Non-Cisco Device Notifications
Aug 8, 2012We're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
Cisco :: CEF Cisco Express Forwarding
Feb 13, 2013I'm trying to understand CEF; I know it's used most commonly in layer 3 switches but that routers can also do it. The routers that support CEF must have special hardware I'm assuming? (Since CEF is layer 3 processes in ASICs) How can we check if a router is capable of CEF? Does anyone know a good link/graphic that shows how much faster CEF is than software-based layer 3 processes?
View 10 Replies View RelatedCisco :: VLAN And Cisco Devices
Aug 29, 2012Basically, I have a network which has a LAN and a DMZ. I need to isolate a few servers and users from the LAN so I created a VLAN on the switch. I assigned it an IP address in a different subnet and assigned ports to the VLAN. Port forwarding is configured on the switch.For testing purposes, before this goes live, I connected a computer directly to one of the switch ports (ge4/5) and assigned it a static IP in that subnet, the gateway being the VLAN IP. I can ping the VLAN IP but I can’t ping the router or get to the Internet,I tried setting the gateway to the ASA VLAN interface (e0/1.4) with the same result.The 1st step is to get Internet access. The next step will be to allow access to the Exchange server on the LAN.There are many devices not shown on the diagram but the important ones are there.
View 12 Replies View RelatedCisco :: AP Roaming With Cisco 7925G
Feb 18, 2013Having a hard time getting Cisco phones to roam 'cleanly' in a Cisco unified wireless environment; Cisco 2504 controller with Cisco LAP1142n (lightweight) APs. The phone SSID is not broadcast and is using WEP encryption. The problem is that when the user is walking around the property, traversing from AP to AP in-call (external and internal calls), they notice the point at which the phone roams from AP to AP - it's literally two or three seconds of no sound and then the call resumes back again. Fast SSID change has been enabled, we've tried locking the SSID to 802.11a only, b only and g only but with only slightly better results when locked to B. We've lowered the client roaming threshold RSSI to -75dB from -80dB, this also yielded better results but still a couple of seconds gap exists. Cisco TAC came in on a Webex session earlier, changed a few QoS settings and advanced wireless settings on the controller, but to no avail. Wireless signal has been proven to not be an issue; several AIRMagnet PRO surveys have been carried out showing the signal throughout the property to meet the -67dB requirement.
View 8 Replies View Related