Cisco Firewall :: CSC Module Installed In ASA 5510 Unresponsive?
Oct 29, 2011
I found my CSC module installed in ASA 5510 unresponsive. I tried to recover / re-image the module with .bin file. but I think it is not possible to re-image because there is no rechability with CSC module, and session 1 command also doesn't work,
you can see the response here.
CS-ASA# session 1
Opening command session with slot 1.
Card in slot 1 did not respond to session request.
CS-ASA#
In this case how to enter into the module?
I removed and inserted the module and tried to reach to it .. but couldnt solve . I just wanted to know whether hardware is dead or not.
View 1 Replies
ADVERTISEMENT
Sep 12, 2012
I have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.
View 3 Replies
View Related
Mar 24, 2011
I am using an ASA5510 and I would like integrate the CSC SSM module in it. What is the Process to upgrade, is it possible and Where I can find it ?
View 1 Replies
View Related
Oct 1, 2012
I have a couple of ASA 5510 firewalls configured and working. I'm now charged with configuring the IPS modules. I'm having to do this remotely. Since the IPS module hasn't been configured I'm guessing it's on 192.168.1.2 with the default username/password.
I'm told that the workstation I access from connects through a switch to the ASA and to the IPS.
I've set the ASA management port to 192.168.1.1. I can't ping 192.168.1.2 - not sure I'm supposed to be able to. In the ASDM, Configure IPS prompts for an IP address. Entering 192.168.1.2 returns "IP address of the management port is unreachable".
View 4 Replies
View Related
Jul 5, 2012
How can I update the expired certificate in AIP-SSM-10 Module using CLI or ASDM.....Here;s the output from the device....and also is there a way I can generate some daily or weekly reports in a graphs.
edge-s2# show versionApplication Partition:
Cisco Intrusion Prevention System, Version 7.0(2)E4
Host: Realm Keys key1.0Signature Definition:Signature Update
[Code].....
View 1 Replies
View Related
Aug 15, 2011
As i'm facing the issue with Cisco CSC module installed on ASA 5510, It hangs up and doesnt work sometime, so it is bypassing all the traffic without inspection through CSC module. After restarting ASA 5510 box, it works fine as it used to work. Now, My question is how can i refresh the module again without interrupting the ASA box/ and how can i avoid this problem forever? Because i cant interrupt the daily work due to this module problem by restarting the box again and again.
View 1 Replies
View Related
Jul 19, 2011
how many NM-32A or NM-16A module can be installed on 3745 and 3640 routers?
View 1 Replies
View Related
Jun 29, 2011
I am going to install new Nexus 7K. Installed SUP and one 32-Port 10Gb module. When I open the box to install this 10Gb module, I saw that there is a carbon paper is tighted with ***** on the top of the module. confirm either it will insert in Switch with carbon paper or have to remove this carbon paper?
View 1 Replies
View Related
Jun 29, 2012
I have cat4500 with subject module. There is strange behaviour over module installed in 3rd slot only, some ports are connected, UP & working fine. But If I am connecting new ports over same module, are not coming UP.Duplex/speed settings already checked & are fine. If i connect same machine to any other module, it perfectly comes up & operation is fine.
View 3 Replies
View Related
Aug 22, 2012
unresponsive / lockups with Cisco ASA 5505 remote management ?
I think it happens like this:
1) With ASDM (Java Web Start), add new crypto map (it could be anything, just happens to be what i added the last time this happened)
2) Click apply
3) ASDM hangs (at this point the Java client becomes entirely unresponsive)
4) ASDM.jnlp refuses to connect and eventually timeout dialog appears. However, VPN connections are still accepted.
5) After a few hours (over night), the ASA refuses all incoming traffic including VPN connections.
View 5 Replies
View Related
Jan 20, 2013
Is there a command that can be used to view what type of SFP module that is installed in Catalyst 3750 switch?
View 6 Replies
View Related
Jul 5, 2012
Main office has a ASA 5520, new office has a ASA 5510. Problem is no traffic goes out when the 5510 is installed, no internet no network connection to servers.I have both config files attached.
View 9 Replies
View Related
Apr 30, 2013
I activated the following Cisco AnyConnect License on my Cisco ASA 5510 running the software version 8.3(2):webvpn has been configured on my ASA, but everytime I try to connect from a Window system (xp, 7 or 8), the process always stops at the menu "Download" (as seen on the image below). My goal is to connect via web-based without doing any manual installation of the Cisco AnyConnect VPN Client on my system.
View 1 Replies
View Related
Nov 15, 2010
I'm currently reconfiguring an ASA5510 installation to a HA setup with a second 5510. The old 5510 has an "AnyConnect for Mobile" license which isn't being used. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. When I'm trying to enable failover I get the message that my mate hasn't got the "AnyConnect for Mobile" license. I know for failover both devices must be exactly the same (at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus). So now I'm wondering and searching for solutions to remove the AnyConnect license (because we don't use it).
View 7 Replies
View Related
Aug 13, 2011
I installed a CSC-SSM-20 module on ASA 5510. After policy services have been enabled, services works well for a few minutes, after that the cpu usage's module rise to 100% and all http traffic is wholy blocked, till the cpu usage go down.This happens very frequently and traffic stay blocked for such a long time that it makes the csc-ssm module unusable. It's disabled right now. ASA version is 8.2(1)and CSC-Module version is 6.6.1172.0.
View 1 Replies
View Related
Aug 21, 2012
I have several ASA-5505 units with the SecurityPlus license. These are running older OS versions and I would like to upgrade them. I am wondering if I will lose the SecurityPlus if I upgrade the image to 8.3
View 4 Replies
View Related
Mar 13, 2013
I am attempting to replace my actiontec router with the Cisco 871 I have little expirience with CLI-IOS so I was trying to use sdm express that failed to load and when I finally got it to load it still didnt work and I ended up getting locked out of the router it was totally unresponsive. So I did a reset and now am attempting to use the Cisco Configuration Assistant to set up my wan connection but it have been loading security related data for 15 minutes and I have a feeling it's not doing anything at all. I don't understand what I'm doing wrong.... Any advice.... I just was trying to get a default set up that would give me internet access Im not trying to enable any of the security functionality at this point.
View 0 Replies
View Related
Feb 17, 2013
If ASA5525 with ASA8.6(1)2 can be browsed using ASDM7.0(1), as currently i'm running ASDM6.6(1) if it will work, any document how to do the upgrade using GUI screen?
View 8 Replies
View Related
Feb 13, 2012
We have just installed a Cisco RV120W behind a third party firewall. All works correctly now, but we are struggling to get the Quick VPN clients connected. I have enabled port forwarding for PPTP & L2TP over IPSEC on the third party router, but still cannot connect (the RV120W was previously used as a primary router & worked perfectly). What ports do I need to open on the third party router to get this to work correctly?
View 4 Replies
View Related
Feb 21, 2012
I have installed a new SSL certificate on our ASA 5500. I removed the old one, installed the new one. And associated the trust points with the interface we use for Web Connect and Any Connect connections.
They are still seeing the old expired certificates. Users can still log in and authenticate but I would rather them see the correct certificate.
View 9 Replies
View Related
Jul 11, 2012
I'm monitoring 2 ASA 5585-x firewalls (in HA mode) using Cisco Prime LMS 4.2.1. The LMS server is connected to the firewalls on the inside interface.
My issue is that I keep on receiving Alert messages on Fault Monitor for both ASA firewalls listing all interfaces (except inside interface) as unresponsive.
My thought is that since the LMS server is not able to ping other active interfaces, it generates these alert messages.
My query is whether I'm thinking right? If yes, how can I prevent these unwanted messages from showing in Fault Monitor?
View 1 Replies
View Related
Jun 18, 2012
So I am an owner of this router for the last 2 years: TL-WR542G - Welcome to TP-LINK . Today it died on me. All of its leds are lightning up, but it doesn't provide a wifi network, and won't give me an interface when i try to access it through 192.168.1.1 on my desktop . There seems to be nothing I can do about it , I tried pushing the reset button on it's back but it does nothing at all.
Do I have any other options to get some life back into it?
View 1 Replies
View Related
Aug 27, 2012
I have an intermittent issue with a new WAG320N.Device is new (installed for 1 month now) and is running the latest firmware "out of the box".
Device was confirmed as working (recommended) via the ISP, as it uses a Broadcom chipset, so it works "more reliably" with the ISP's hardware which uses the same chipset.
Setup was painless and the router synced up fine and has been operating for a few weeks. However, twice in the past week the router has become unresponsive to ping over the LAN. Furthermore, the device's lights indicate everything is OK, however I have to reset the router (power cycle) and then it returns to normal.
WIFI is OFF. LAN IP is set manually, DHCP is OFF. The router is plugged into it's own UPS.
View 1 Replies
View Related
Aug 26, 2012
I have a Synology NAS that is connected to several IP Cameras through a SG300 switch. From time to time the IP cameras become "disconnected" at random When I reboot the switch, the access to cameras is re-established.
Problems: it requires an external device to reboot the switchall ports are shutdown while rebooting the switch
Q1 Is there a way to program the SG300 to reboot itself automatically every X hours?
Q2 Is there a way to automate the following process on the SG300 switch itself. ping a camera every 1 minutesafter three unresponsive ping, shutdown and restart the port to which the camera is connected
View 7 Replies
View Related
Jun 3, 2012
Router: WRVS4400N
Firmware: 2.0.2.1
Background: Port forwarding external port 1234 to internal port 123 on a NAS appliance (ip 192.168.1.111) Successfully accessed NAS like this: [URL] Everything was working perfectly for several weeks Last week I changed the subnet to 172.17.888.x
Problem: Everything back to normal on the LAN except that port forwarding to the NAS no longer works.
Gerfingerpoken: I opened another port (1235) and forwarded that to the NAS (in addition to the original port). No success.
I tried a port scanner. The port scanner reported that port 1234 was open on the router, but didn't mention 1235. I repeated with yet another port. Same result: only port 1234 is reported open by the port scanner. Software rebooted the router, same result Hard reset (button) the router, still no change.
QUESTIONS:
1. How can I test if the router is actually forwarding new ports? (software tool?)
View 1 Replies
View Related
Jul 5, 2011
Every 25 minutes, sometimes sooner, sometimes later but usually on the dot I get limited access and the router interface becomes inaccessible for about 1-3 minutes. My problem is my room mate has left for the week and the router is locked in there. I am unable to connect hardwired or power cycle the router. I have the password for the connect and I just got the PW for the router interface. I also have remote capabilities. I have been trying many things to stop it from being so slow and unstable but basically even though my signal reception is 4-5 bars I am only averaging 11mbps speed. I am using a b/g alfa 1w adapter but this shouldn't be the cause of the slower speeds. I can only achieve 1-3mbps down on speedtest.net whereas before I was getting 6-12mbps down.
-UPnP Off.
-NAT Firewall Open.
-300mbps Max
-Channel 1 no other channels within 5 channels near it.
-WPA2-PSK [AES]
-Default MAC Address
-Automatic Configuring of all IP Addresses
-MTU 1500
-WMM On.
Being limited by lack of power cycle and hardwired connect makes it a little harder. I know it's fixable without that though. Also there is no point of a hardwired connect unless I am upgrading the firmware (it already has the newest firmware by default) because I know it should work fine like that. I have tested connecting to other networks and I do not d/c on them. My own research has shown that setting a static IP resolves the issue. I am unfamiliar with exactly how to set this up for the router and the client and if it involves dealing with the ISP (Comcast)
View 9 Replies
View Related
Feb 1, 2011
My DSC-930L's web interface becomes unresponsive about an hour or two after power cycling my camera. It still responds to pings, and it still sends images to FTP when it detects motion, but I can't log into it via web interface, mydlink, or the iphone app. Power cycling the camera fixes the problem for an hour or so but then its right back to not working again.
View 8 Replies
View Related
May 9, 2011
I have FSWM active/standby installed in 6509-E core switches running following FWSM Firewall Version 3.1(3) Device Manager Version 5.0(2)F..I want to upgrade to latest FWSM version as well as ASDM, I downloaded asdm-622f.bin and c6svc-fwm-k9.4-1-5.bin from cisco portal. When i checked the show version of FWSM, it says..The Running Activation Key is not valid, using default settings: Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000
I have gone through threads on CSC about how to upgrade FWSM in failover mode, now my concern is, Do i have to take care about activation key or keep as it is ? I have maintenance contract with cisco for all devices.
View 3 Replies
View Related
Nov 3, 2012
My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.
View 1 Replies
View Related
Mar 1, 2013
Region : France
Model : TD-VG3631
Hardware Version : V1
Firmware Version :
ISP :
I tried to upgrade a TD-VG3631 that came with firmware version TD-VG3631_V1_120929 to the latest TD-VG3631_V1_130108 version.[url]...Is there a recovery procedure to flash back a firmware?
View 2 Replies
View Related
Aug 9, 2012
I got a refurbished EA4500 (directly from Cisco) last week. I have been having a few issues, which I have found (not too great) workarounds for. However, the latest issue has me stumped, and is unacceptable.Whenever I am transferring files between 2 computers, I get kind of OK speed (5 MB/s). However, while this transfer happens, no other device can connect to the net. Actually, even trying to go to router home page (192.168.1.1) times out.The clients still say they are connected to the router, but I just can't get anywhere.As soon as the file transfer finishes, everything goes back to normal.EA4500 replaced a WRT54G. Never had any problems with that router. It was such a workhorse. Just needed to upgrade to a n-router.I am on the latest non-cloud firmware.I have reduced the MTU size to 1200. Not sure that matters.
View 9 Replies
View Related
Jun 2, 2013
We have installed 5585-x in active/active mode with transparent firewall. We have created two virtual sersors for vs1 and vs2 in IPS module and linked with ASA context C1(vs1), C2(vs2) and admin(vs0).
As firewall is working in transparent mode, we have bridge IP address for context C1 10.1.1.1 and for context C2 10.2.2.1.
I have added default routed for context C1 10.1.1.2 .It is in the outside of asa and SVI on switch.For the other context C2 10.2.2.2.
IP address range for the IPS module and what should be the gateway for IPS module.AS the traffic is coming from outside and going to inside interface of ASA.
View 1 Replies
View Related
May 14, 2011
I am configuring new ASA 5520 with AIP module for our network with HA (2 boxes), would be the best practice to configure in order to protect web servers and email server.
View 2 Replies
View Related
