Cisco :: Redundant Link Between Switch And Router
Nov 30, 2012
Can someone give me a sample router config (Cisco801) for the below scenario. Not familiar with networking.Server with 2 nic, connected to 2 different switches, each switch connected two lan interfaces of Same cisco801 for redundancy.Server must be able to reach gateway IP (in router) in case of either switch failure/server NIC failure.I also have 2 vlans, going to use same link for management vlan and application vlan.
View 11 Replies
ADVERTISEMENT
Mar 9, 2012
I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
View 1 Replies
View Related
Oct 8, 2012
Current our environment is the following:
Core1 ---- Core2
| |
Nexus5k
| |
N2k, N2k, N2k (FEX)
||
Servers, hosts, etc..
We would like to add another Nexus5k to this topology. However, it has to be a zero downtime infrastructure add-on. When setting up the keep-alive, peer-link, vPC and vdc domain, will there be any upset in network traffic on the current N5k?Also, are the Nexus5k configurations synchronized or are they independent from one another? Before setting up the new 5k, should i configure it to teh 6509's, and vPC's to the Nexus2k's before setting up peer-link?
View 2 Replies
View Related
Nov 18, 2012
Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?
View 5 Replies
View Related
Mar 27, 2012
I have 2 6504's running HSRP as my core. They are each etherchannel'd to my Datacenter switch (3750 Stack) -- see image below.The problem i a having is with the etherchannel status:
Core1 PO11 status w (waiting)
Core2 PO11 status P(bundled)
DC11 PO48 status P -- but only to Core2 - the interfaces to Core1 are suspended. (See attached configuration documents) None of the devices have any information in the logs. I run this same configuration in my central location, but we are running Nexus 7000's. With the 6500's, do I need to split the port channels on the 3750 to allow them to negotiate the etherchannel? If I split the portchannels, are there any concerns? Should I expect to see the etherchannel status as P (Bundled) or H (Hot-Standby)?
View 2 Replies
View Related
May 15, 2012
We have 6 sites which are connected through E1 links.All sites connected from HQs.
Site A is HQs.
Sited B, C, D, E, and F are Branches.
Site A is directly connected with site B, C, D and E.
Site D is connected with Site F.
Now we have another redundant E1 link for site C and Site F.we are using Static Routes.i have configured Qualified-next-hope on Juniper Router but i am unable to configure IP SLA on Site C Cisco 2951 with IOS 15.0 router.is there another solution for my scenario plz share with me for Redundant Link.
View 1 Replies
View Related
Jan 6, 2012
below is the current config of link that is already up. I need to add another fiber redundant link between 6509 and 2960 stack. How to work on config Spanning side by not taking 6509 down after the change. 6509 is in distribution.
---------------X-ALPHA-IDF-1FORMS-2960S-0# (SIDE)
!interface GigabitEthernet1/0/52description X-ALPHA-F-6509-0 uplinkswitchport trunk native vlan 18switchport mode trunksrr-queue bandwidth share 1 50 30 19priority-queue out mls qos trust dscpmacro description cisco-routerauto qos trust spanning-tree portfast disablespanning-tree guard loopip dhcp snooping trust!
-----------------X-ALPHA-F-6509-0# (SIDE)
!interface GigabitEthernet3/10description 1st floor POC2 Forms IDFswitchportswitchport trunk encapsulation dot1qswitchport trunk native vlan 18switchport mode trunkno ip addressmls qos trust dscpspanning-tree guard loop!
View 1 Replies
View Related
Jun 18, 2011
I have already raised this discussion on "LAN, Switching and Routing" group. But I guess this is the right group for my queries. So I am sending my queries in this group again.
We are using CSS 11503 with one 16FE line card. We have connected 3 servers with redundant link. So FE1-2 in Server1, FE 3-4 in Server2 and FE5-6 in Server3. Our system team has configured APA in their servers as they are using HP-Ux.
1) Do we need to do any configuration at line card.
2) Do we need to do ether-channel at loadbalancer end. if yes, can you share me any cisco doc on how to do it.
View 1 Replies
View Related
Feb 24, 2013
I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
View 4 Replies
View Related
Jun 7, 2012
i am using cisco 2821 router at the edge in my network where the WAN link is terminated.i want to configure Redundancy . So will 2821 support ? If yes what is the another router .Is it the same series or different for redundant configuration.
View 2 Replies
View Related
Aug 8, 2012
I have two ISP need to connect them on my router.
The Router that I have is 2811 where it contains two Fa ports only, so I put an access switch between the two ISPs and the Fa0/0 then configured the Interface Fa0/0 with two IPs ISP1 and ISP2 as a secondary.
The problem that I faced that when ISP1 become down the another secondary IP (ISP2) stay down and the internal users have no access to the internet.
View 1 Replies
View Related
Apr 10, 2013
I have a peculiar issue with a router whering I get the message in the Show Environment as below.
sh environment out
Redundant Power System is not present.
SYS PS1 is present.
Type: AC
AUX(-48V) PS1 is absent.
Fan 1 OK
Fan 2 OK
Fan 3 OK
Fan Speed Setting: Normal
Alert settings:
Intake temperature warning: Enabled, Threshold: 55
Core temperature warning: Enabled, Threshold: 70 (CPU: 95)
Board Temperature: Normal
Internal-ambient temperature = 22, Normal
CPU temperature = 37, Normal
Intake temperature = 22, Normal
Voltage 1(3300) is Normal, Current voltage = 3300 mV
Voltage 2(5150) is Normal, Current voltage = 5210 mV
Voltage 3(2500) is High/Low, Current voltage = 2168 mV
[Code]...
View 4 Replies
View Related
Oct 26, 2011
Can't get cisco router and switch to see each other? When I connect the 2620 router to a 2950 switch no link lights turn on. It's the same when I connect any router to either of the two 2950 switches I have. I can connect to both switch and router from a pc using telnet and the router can connect to a regular tp-link switch. I'm a newbie when It comes to Cisco. Here's the running config for the router and switch. There Is no connection when using any of the switch ports to connect to the fa0/0 of the router. [code]
View 17 Replies
View Related
Feb 26, 2013
I have a TP-Link WR541G/542G router which I would like to utilize as a switch to connect my xbox 360, blue ray player and TV box to the internet. The switch is connected to a powerline adapter and another adapter is connected to the main router Huawei HG533. I have tried to follow your instructions I found in the thread however it did not work.
View 2 Replies
View Related
Apr 15, 2012
Upstairs I have my internet coming in with a Comcast modem/ router ( I will be bridging this b'cuz it sucks as a router). Also, I have my Dir 655 upstairs that I will use for wireless. and I have my dir615 downstairs and I want to use it as a basic switch/wired router. How do I set up my dir615 as a switch/wired router?
View 1 Replies
View Related
Feb 8, 2011
I have a 3640 router with 4 Fast Ethernet Network Modules (1fe-tx, 1fe2w & 2fe2w-v2) and a Catalyst 2912 switch. I can not acheive a link between the 2 devices. All four will not get a link light and the interface(s) show no errors. If I plug the Router nic into virtually any other switch or workstation it works flawlessly. I put a switch between the catalyst and the 3640 and it works without error.
Steps I have tried...
1. Configure interfaces on both Switch and Router to Auto Speed, Auto Duplex2. Configure interfaces on both Switch and Router to speed 100, Full Duplex3. Try Both Crossover and Straight-Through verified working cables.4. Tried a second 2912xl-en switch
Both 2912 switches are factory defaulted, other then the changes I made to the speed and duplex to try to get them connected.Both the router and switches have been doing other functions (seperatlly) within our network for years?So my question is...Why is the NICs in the router compatible with every other vendor other than CISCO?
View 5 Replies
View Related
Apr 29, 2011
On my D-link routher the power supply broke. I instal another one but it has 2.5A as output instead of 2A as the broken one has. Is it dangerous.
View 2 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
View 1 Replies
View Related
Mar 29, 2013
Every so ofter, the switch of the router just stops moving traffic between the LAN and to/from internet, though the WiFi keeps working and can still use internet.
I can still use the router's switch, and ping other computers on the local LAN, what happens is that the router stop routing wired traffic from/to internet, the rest of the issue is still the same, I opened reddit on my smartphone and there it was working via WiFi, but the would have none of it for the computers on wired LAN, not even accessing the router's page or telnet.
It is like some service or bridge between the switch LAN and the router itself dies... I'm still clueless.
The only "pattern" that I see is that my desktop is on line, because I can be not at home for 12+ HS and I can connect remotely to the server (rd p and trans droid) so I know it has internet access, but sometimes I think this happens when I turn on my desktop, like just now, this morning, but again, I feel is not every morning, trying to be more scientific about it I come here after every time it happens to record it, and also set the record straight about the issue description.
So, assuming it is not a hardware issue, because I did not had this problem in all 2011 and 2012, I do not overclock the router neither use other than default TX power level.
- How do I begin diagnosing this issue?
- If it is a known issue with this builds? I could no find it.
My goal is to be able to provide info for debugging the problem and possible finding a fix/workaround it. If it is indeed hardware failing, how do I even begin to diagnose it from that POV? The message is empty...
Even with the new build r21061 still happened two more times. Now the real problem to me, is that I cant even revert it to stock firmware, I tried even with:
- unplug router
- press and hold reset
- plug router
- keep pressing until power led blinks orange
- enter 192.168.0.1 (PC must have static IPA, i use 192.168.0.200)
Can't open 192.168.0.1 in FF nor chrome and does not even ping. [URL]. I just want to get it back to stock or do not hang up the switch-to-router(ing).
View 1 Replies
View Related
Jan 16, 2012
this router of my girlfriends only works when iplug the dsl modem into the output ports what could possibly cause this. would a firmware upgrade straighten it out...
View 1 Replies
View Related
Aug 3, 2009
In ASA 8.0,I have following queries related to redundant interfaces
a)While configuring redundant interface can the redundant interface again be divided into logical interface like red1.1 , red1.2 ?
b)Is Redundant interface supported in the Multiple context mode
View 4 Replies
View Related
Feb 24, 2012
Does OSPF work between a VSS L3 MEC & an ASA Redundant Interface? Both 6509 are in VSS and a L3 MEC is formed to the ASA.Both ASA ports are a part of a L3 Redundant Interface. Please note there is only a single ASA in this topology. [code] Now, the OSPF neighboring does occur and go into the FULL state on this device, however soon enough, the state enters INIT/DROTHER state.But as soon as I disconnect the physical connection 6509(Standby) The OSPF adjacency goes into FULL mode.
View 5 Replies
View Related
Dec 5, 2010
What is the purpose of Redundant Port that says "future use RJ45" on the Cisco WLC 5508?
View 3 Replies
View Related
Dec 7, 2010
We need rededunt uplink in Cisco 2960 from Cisco 3550 , one uplink is primary and one is for backup.As per current scenerio one uplink in Cisco 2960 interface fe0/1 from Cisco 3550 int fe0/1 through OFC cable configuration 2960 int fe0/1 interface fe0/1desciption *** Connect to Cisco 3550 port 1 ***switchport mode accessswitchport access vlan 2spanning-tree guard loop Configuration Cisco 3550 int fe0/1desciption *** Connect to Cisco 2960 port 1 ***switchport mode accessswitchport access vlan 2spanning-tree guard loop We have facing the problem when OFC cable down , so now we are considering anather OFC via anather route to connect same Cisco 2960 Switch in Fe0/2 from Cisco 3550 int fe0/2 so when primary uplink goes down then backup uplink which is connect to Cisco 2960 fe0/2 from Cisco 3550 fe0/2 it's up.what is the command we need configure as per my require in both the Cisco 2960 and 3550 swith in interface and global mode also.
View 10 Replies
View Related
Jun 11, 2012
Q: a client has a network with 60 AP's controlled by a AIR-CT5508-50-K9 (+ L-LIC-CT5508-25A) with a redundant power supply. Can he get full redundancy by purchasing a second controller? If he purchases one, can he bring it into the network? What about the extra license for 25 extra AP's installed on the first controller?
View 4 Replies
View Related
May 29, 2013
We are small transit ISP for other downlinks. And currently have such setup 7201 and 7206NPE-G1, as core and edge routers also we have connected to IXP. Downlinks usually BGP connected to one of border router which is terminated via VLAN, thus sub interface. IXP are also connected via VLAN on router.
What I don't like about this is when one borderd goes down downlink will lose connectivty, also recently we start growing and getting more downlinks, so balancing between borders become problem. So my question is, how to make setup less fragile and more redudant.
View 1 Replies
View Related
Oct 29, 2011
How to replace a defective redundant sup. I read on several articles that inserting new redundant sup should not be an issue as the active sup will always send its configuation to the standby. We are running SSO on the Sup720. Should I switch it to RPR before I install the redundant sup? I read a case wherein they switched it to RPR from SSO before inserting the new redundant sup. My concern is the IOS mismatch since Cisco doesn't always send the same IOS on RMAs.What I am planning is this.
1. Save/Backup configuration
2. Remove the redundant sup on slot 8 (since it is a 6513)
3. Insert the new redundant sup on slot 8.
4. Check if all the configurations were synced from slot 7 to slot 8.
5. Copy the IOS from sup-bootflash to slavesup-bootflash. (if the IOS are not the same)
6. Check show bootvar to see if the boot variables are correct.
7. If bootvar is the same, reload slot 8 to boot the new IOS.
Is this a good plan or am I missing something? I am worried with this document if the redundant sup has a different software. If i insert the card in slot8, according to Cisco, it will revert to RPR. If slot 8 boots and it has a different OS, then slot 7 will switch to RPR even if it's active. Would I still be able to access the slavesup-bootflash of slot 8? Is it going to boot 100%? I read that doing a force switchover will cause a flip and RPR would cause the line cards to reinitialize and I don't want that. Well I am not going to do a force switchover since i want slot7 to be active and retain slot 8 as hot.
View 3 Replies
View Related
Sep 21, 2012
We have 3750-X's with dual power supplies. When one of them is disconnected the NMS/Netcool is not picking up the trap. What MIB is needed to monitor the power supplies?
View 1 Replies
View Related
Feb 14, 2012
I am configuring a pix 525,i just found out how to activate the subinterface on it so that's good,the box has a primary unit and secondary unit, both are connected from G0 to redundant switches,if i do a show failover, it says it's using the serial based lan failover, which is fine by me,however, do i need to create a single, regular interface.. or a redundant interface?,i.e. if i create a regular subinterface, will failover still apply to this interface?,or for failover to work, do i need to create a redundant interface (with a redundant id)? i do not seem to have the option to create a subinterface when adding a redundant interface.
View 7 Replies
View Related
Dec 26, 2012
We have a six node MPLS network, all nodes route to our main office for a variety of services (email, core, fire shares, Internet, etc). Therefore, the link to our main office is crucial. In the event that the MPLS link to/from our main office becomes unavailable, we would like to establish a secondary route into our main office via virtual private network. Our main office and two branch offices have redundant broadband internet connectionsWe currently have Cisco 1921 routers as our branch routers and a Cisco 2800 as our “core” router at the main office. We also have two SonicWall TZ-200 series firewalls at the two branch locations and a SonicWall NSA-2400 at our main office. The VPN connection seems to work okay.How would I configure my branch routers to advertise and route traffic out the VPN connection in the event that the MPLS leg to/from our main office is down?
View 3 Replies
View Related
Apr 25, 2012
Currently we are using a single connection to our ISP and in the coming months will be moving to a two seperate connections (to same ISP). In our current setup we utilize active/passive ASA's (5520, single context) and would like to utilize that going forward as well, the reason being is our DMZ's all hang off of these ASA's and we have fiber connectivity between our datacenters.Our main datacenter and DR Datacenter are basically one big LAN with fiber between them, so we have our DMZ networks at both locations currently with both terminating in our ASA's. That way if the ASA at our current site fails the DMZ's are still accessible via the secondary firewall at our DR facility.
View 1 Replies
View Related
Mar 10, 2013
I am setting up two 5508 controllers, one in HA mode, and one the primary for the remote sites in question. I plan to have these units service wireless for MPLS conected regional sites (each with their own local subnet). I was planning on using the cabled hosts network in each site for the wifi addressing and was thinking a different addressing for Guest Access, is this common? I'm obviously concerned with guest access clients but don't know enough how their trafiic is segregated from normal wifi traffic.
Also, when I stand up the controllers the management interface and ap-manager won't be in the same network as where the hosts or LWAP's will reside (routing access will exist though).
View 6 Replies
View Related
May 8, 2011
I have two ASA 5540s, ver 8.4 configured in Active/Standby failover.I am also using the redundant interface feature for my Inside interface. Gig0/0 is the active primary and Gig0/1 is standby.
I will activate failover monitoring of the Inside interface using the monitor inside command.
My question concerns the failover monitoring of the redundant interface. If the gig0/0 connection were to fail would the Gig0/1 interface become Active, AND simultaneously result in a full device failover?
Or, does Gig0/1 of the Inside interface redundant pair simply become active and not change the Inside interface device failover state? Thus NOT resulting in a device failover.
View 1 Replies
View Related
