Cisco :: Reporting Error In WCS 7.0.172.0
Sep 27, 2011
Runing the report, "CleanAir > Worst Interferers" and I get this error
The specified criteria did not match any data for the report. Make sure that the following background tasks are running: 1. Interferers
I know there is data that should match up because I can see it on the individual controllers. I checked the background task Interferers and it appears to be working as well but just to make sure I forced the "Execute Now" command but the report still failed.
View 4 Replies
ADVERTISEMENT
Jan 31, 2011
Is there any way to get reports on voice utilisation on WAN links so that CAC settings can be proactively managed for each location on our CUCM cluster? Our service provider is advising that this is not possible which means that we rely on customer/staff complaints to recognise where CAC thresholds are being reached. Our preference is to be able to run traffic reports (or the Cisco equivalent) as could be done on our previous (traditional) telephony network and provide additional capacity if and when required BEFORE congestion is reached, thus minimising customer/staff impact.
View 1 Replies
View Related
Jul 31, 2011
WCS is reporting few AP's are not associated with it. While troubleshooting, AP conneceted switch interface shows UP/UP and show power inline output gives IEEE PD instead of AIR-LAP1131AG-E-K, after doing a shut/no shut on AP connected interface. Later after sometime AP comes up.
View 5 Replies
View Related
Mar 6, 2012
I'm currently running Cisco LMS 4.1. I need to see if there is a way in the LMS, either through the menu or via a report, that can give me the V LAN numbers, the description, the IP address, the Interface (SVI) the v LAN is on and the route it takes.
I've searched near and far and haven't come up with anything yet.
View 3 Replies
View Related
Sep 26, 2011
we are running WCS 7.0.164.3 and wonder whether is there any reporting option availabel that can give us daily report on Top 50 or Top 100 APs by client count.
I know that I can look at the client tab under WCS home page and see the top 5 APs by client count on real time.In our environment we have around 700 APs and would like to know by having this kind of report which APs are mostly hit ?
View 5 Replies
View Related
Jan 31, 2011
I have not managed to get the Monitoring to work on the ACS 5.1. This is an eval version. Advanced monitoring and reporting is installed on the ACS. This is my configuration on the Cisco Router
aaa accounting exec default start-stop group tacacs+aaa accounting commands 0 default start-stop group tacacs+aaa accounting commands 1 default start-stop group tacacs+aaa accounting commands 15 default start-stop group tacacs+aaa accounting connection default start-stop group tacacs+
logging origin-id iplogging facility sysloglogging source-interface GigabitEthernet1/1logging host 1.1.1.1 transport udp port 20514
logging monitor informational
epm logging
On the ACS, when I open the dashboard --> ACS health -> I get Status not available.Global Instance under Logging Categories been configured for local logging?
View 4 Replies
View Related
Jan 8, 2011
I just upgraded yesterday to the DIR-655 (ver B1, F/W Ver 2.00NA), and suddenly my sons Xbox 360 complains that the NAT is set to moderate. I'm not really sure what this means, but I've never seen it before and it wasn't an issue with my old router. It pertains to the DIR-655? I did some quick google searches and I've seen lots of different 'solutions' to this issue, but none of them seem to agree with each other and I'd rather not spend and entire afternoon trying one after another given that this router kills my internet connection for a full 20 seconds every single time I make any change.
View 4 Replies
View Related
Apr 27, 2012
We have discovered Nortel/HP C-GbE2 switches on our network are sending spanning tree Topology Change Notifications (TCN). The HP switches only have servers connected and no other switches leading to any other network segment so we are not clear why the switches are sending spanning tree TCNs every second. We do not have a support contract. Can anyone on the Cisco side speak to what's referenced on page 5-6 of the attached document? I found the attached document which talks about diabling spanning-tree (page 5-6) in Cisco environment but wanted to consult with an expert before proceding. Document (Configuring Nortel Gigabit Ethernet Switch Modules for IBM BladeCenter in a Cisco Environment Solution Brief.
View 0 Replies
View Related
Dec 23, 2011
I noticed one awkward thing with the latest 1.0.3.5 firmware for the Cisco Small Business RV220W router, with previous firmwares there has always been reported 128mb of system memory (RAM) under the router dashboard. And several "teardowns" of this router has confirmed it to have 128mb of memory on the router board.
Does that mean the latest 1.0.3.5 has an odd visual bug, or has the RV220W gotten it's memory sliced in half with this firmware release?
View 4 Replies
View Related
Jun 12, 2013
Is there any way to determine how much bandwith users on a particular WLAN (Guest) are using on the 5508 or by any other means?
View 9 Replies
View Related
May 16, 2011
I'd like to know if there is a way to exclude passed authentications for a specific username from reporting in the Authentications-TACACS and Authentications-RADIUS reports?
We have a few usernames that are used in scheduled jobs. We only need to know when they fail authentication, so we don't need to fill up the reports with every passed authentication from these accounts. Can this be done?
View 1 Replies
View Related
Apr 23, 2013
I'm using ASA 5510 and I wondered if we can configure reporting to know the traffic on each interface,the attacks,the vpn connection during a period ( 1 week or 1 month). For the moment, we can see these logs only in 'real time' .
View 1 Replies
View Related
Jan 1, 2013
We have 2 ASA 5505 located in head office (173.212.xxx.xxx) and remote site (50.34.xxx.xxx) and site-to-site VPN has been established between them.everything is fine but the ASA in head office keeps reporting below 402120 syslog message.
4 Jan 02 2013 12:30:34 402120 50.34.xxx.xxx 173.212.xxx.xxxIPSEC: Received an ESP packet (SPI= 0x384E1C57, sequence number= 0x2AE77) from 50.34.xxx.xxx(user= ) to 173.212.xxx.xxx that failed authentication.
Even though, VPN tunnel is not dropped.
View 2 Replies
View Related
Jan 10, 2013
1) How do you manage your inventory of network equipment from the time you receive a product into inventory to the time you decommission it?
2) How do you make aware the people who manage your network monitoring/reporting software that a device has been added/removed from the field?
2a) How do you notify the people who manage your network monitoring/reporting software of what is to be monitored on a new device in the field? Of a new interface that has been added/removed on an existing device?
2b) How quickly do you notify for 2/2a? i.e. minutes, hours, days, etc.
3) What types of interfaces and resources do you monitor on a network device?
View 3 Replies
View Related
Mar 20, 2011
I have just gotten a new touch phone that has wifi. and i wanna use it through my dlink dir-825 router. My phone is the nexus s with 2.3 andriod OS.The problem is that my phone can see the 2.4 ghz connection it just keeps reporting "deactivated" i did acess other wifi and used the internet over a router. So i know the phone works.
So my question is: 1. Can i make my router ONLY be in 2.4ghz mode, if so, can you link or explain it?
View 7 Replies
View Related
Mar 26, 2012
I am configuring new ACS 1121 appliance with version 5.3 and wanted to know how to configure Remote Database settings in ACS5.3 Is that necessary to configure that option ?
Also one more thing I can see that ACS 5.3 generates lots of logs is there any solution to reduce such logs. It seems many unuseful logs which are system related are getting logged into device which might no be good for memory requirements of device.
View 6 Replies
View Related
Nov 27, 2011
We have a pair of 6509 working in a VSS configuration (IOS 12.2(33)SX5). The 6509s connect to a pair of ASAs (7.2 code) running in an Active/Standby setup. These ASAs in turn connect to routers going to remote sites. I have configured Netflow on the following VLANS,
VLAN 10 - Servers Vlan
VLAN 9 - Transit/ASA VLAN (connects ASAs to 6509s). All traffic originating from any VLAN on the 6509 crosses this VLAN in order to reach remote sites and vice versa
I configured the netflow source VLAN 11 although I am not collecing any netflow from it.Although I have been getting lots of Netflow info, I noticed that netflow for traffic originating from any user VLAN on the 6509s going to any remote site via TRANSIT/ASA VLAN(9) does not get reported, I even tested with 4 GB traffic but no result. Only reverse traffic (i.e. from remote site to user VLAN) is reported as it traverses the Transit VLAN (9).
I read somewhere that egress netflow is not supported in 6500, but isnt traffic originating from a user vlan to a remote site via the transit VLAN (9) considered ingress with respect to the transit VLAN (9)? I would like to know whether bidirectional Netflow is supported on 6500 VLANS. I have mimimum control on routers beyond the ASAs, and since these ASAs run 7.2 code netflow is not supported, and Monitoring this Transit Vlan gives me extremely useful info.
I do get netflow biderectional traffic from the Server Vlan 10, but I think it is correlated by the netflow collector from vlans 9 and 10. [code]
View 9 Replies
View Related
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
View Related
May 1, 2012
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies
View Related
Apr 20, 2011
i'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies
View Related
Oct 20, 2011
I'm receiving a lot of this log message:
com.sybase.jdbc2.jdbc.SybSQLException: SQL Anywhere Error -193: Primary key for table 'Technology_Device_Template' is not unique
at com.sybase.jdbc2.tds.Tds.processEed(Tds.java:2884)
at com.sybase.jdbc2.tds.Tds.nextResult(Tds.java:2206)
at com.sybase.jdbc2.jdbc.ResultGetter.nextResult(ResultGetter.java:69)
at com.sybase.jdbc2.jdbc.SybStatement.nextResult(SybStatement.java:220)
[Code]...
View 1 Replies
View Related
Apr 10, 2013
I have implemented 802.1X with ACS 5.3 and switches 2960 without problem.The thing is that one port transitioned into err-disabled and I dont know why.I dont have any logs to see what caused this.Is there a command to see why this happenedWhat do you think could cause this?
View 4 Replies
View Related
Apr 2, 2013
I just got two Prime NCS Servers for my system and they came with 1.2. My management wanted to run the lastest IOS which is 1.3. So as soon as I set the physical equipment up, I downloaded the latest 1.3 IOS for the site and burned it on a DL DVD and reimaged the appliance.
View 1 Replies
View Related
Mar 8, 2011
I can connect to a 877 router via SSL, however when I click on “Start” for Tunnel connection a separate window is opened with a “Website not found 404 error”.
View 2 Replies
View Related
Aug 16, 2011
We have Cisco 7609 Router and SIP module at slot.Now we are getting this error continue from yesterday asgivenbelow,
%SPA_CHOC_DSX-3-HDLC_CTRL_ERR
Also find attached show logging, show version, show module command output.
View 2 Replies
View Related
Jun 3, 2013
ACS 5.4, when I was working in it. In the CLI appeared this file to solution I have to reload the ACS.
SMflag : 1Cmd str: haltSave the current ADE-OS running configuration? (yes/no) [yes] ? noContinue with shutdown? [y/n] Func Trace: <<< vsh_mark_process_status >>>22007: Terminated by signal 2.EOL ==>completedJob is completeRestored the shell's terminal mode.EOL: abnormal exit: code: 0EOL: signaled: 2 InterruptCmd execution successful
[Code] .........
View 3 Replies
View Related
Jun 6, 2012
I built a new Win2k8 server meeting all prereq's. This is a new install of LMS. Right at the beginning of the install process, i get this error and the install halts.
View 2 Replies
View Related
Mar 25, 2011
I got my modem about 3 months ago, I had no problems logging into my PSN account since last week. First, I was getting a DNS error. I was searching for a solution and I fixed the problem, the internet connection on my PS3 was working only for about a day. Later I started to get the 80130182 error, I tried to reset my modem and my PS3, I have unplugged everything and I plugged it back in, still didn't work. The internet connection on my PC works perfectly, only the internet connection on my PS3 doesn't work.
View 4 Replies
View Related
Apr 1, 2013
What could cause this log message and put the port in errdisable?
15w2d: %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on FastEthernet0/22.
15w2d: %PM-4-ERR_DISABLE: loopback error detected on Fa0/22, putting Fa0/22 in err-disable state
15w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
View 19 Replies
View Related
Aug 2, 2011
I’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
View 6 Replies
View Related
Aug 28, 2012
When I run installation process I have received unexpected error:I have windows 2008 R2 x64. Antivirus is disabled and I have administrator privilege.
View 6 Replies
View Related
Jul 30, 2012
Error : compressed image checksum is incorrect 0xDC5C5348 Expected a checksum of 0x066C5349I have uploaded a new firmware but same issue after booting, I have check the MD5 checksum in the image and Cisco and they are matching and verified, what could be the reason for all of this ??
View 2 Replies
View Related
Dec 18, 2012
Our customer is try to make a configuration by web interface menu:
Admin > Collection Settings > Inventory
After select the menu below they always received this message:
Error in starting acquisition: unable to connect to server
View 1 Replies
View Related
