We have Cisco 7609 Router and SIP module at slot.Now we are getting this error continue from yesterday asgivenbelow,
%SPA_CHOC_DSX-3-HDLC_CTRL_ERR
Also find attached show logging, show version, show module command output.
Removing and Installing a Supervisor Engine on a cisco router 7690 and more important IOS upgrade of this module.
I need some kind of manual, but I would prefer a short procedure to do this change. A brief of the steps to do that. Also i don't if i have to upgrade the new module after install it.
PD.
IP7VAL02#sh modMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1034Z32J 2 48 CEF720 48 port 10/100
[Code]....
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies View Relatedi'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies View RelatedI'm receiving a lot of this log message:
com.sybase.jdbc2.jdbc.SybSQLException: SQL Anywhere Error -193: Primary key for table 'Technology_Device_Template' is not unique
at com.sybase.jdbc2.tds.Tds.processEed(Tds.java:2884)
at com.sybase.jdbc2.tds.Tds.nextResult(Tds.java:2206)
at com.sybase.jdbc2.jdbc.ResultGetter.nextResult(ResultGetter.java:69)
at com.sybase.jdbc2.jdbc.SybStatement.nextResult(SybStatement.java:220)
[Code]...
I have implemented 802.1X with ACS 5.3 and switches 2960 without problem.The thing is that one port transitioned into err-disabled and I dont know why.I dont have any logs to see what caused this.Is there a command to see why this happenedWhat do you think could cause this?
View 4 Replies View RelatedRuning the report, "CleanAir > Worst Interferers" and I get this error
The specified criteria did not match any data for the report. Make sure that the following background tasks are running: 1. Interferers
I know there is data that should match up because I can see it on the individual controllers. I checked the background task Interferers and it appears to be working as well but just to make sure I forced the "Execute Now" command but the report still failed.
I just got two Prime NCS Servers for my system and they came with 1.2. My management wanted to run the lastest IOS which is 1.3. So as soon as I set the physical equipment up, I downloaded the latest 1.3 IOS for the site and burned it on a DL DVD and reimaged the appliance.
View 1 Replies View RelatedI can connect to a 877 router via SSL, however when I click on “Start” for Tunnel connection a separate window is opened with a “Website not found 404 error”.
View 2 Replies View RelatedACS 5.4, when I was working in it. In the CLI appeared this file to solution I have to reload the ACS.
SMflag : 1Cmd str: haltSave the current ADE-OS running configuration? (yes/no) [yes] ? noContinue with shutdown? [y/n] Func Trace: <<< vsh_mark_process_status >>>22007: Terminated by signal 2.EOL ==>completedJob is completeRestored the shell's terminal mode.EOL: abnormal exit: code: 0EOL: signaled: 2 InterruptCmd execution successful
[Code] .........
I built a new Win2k8 server meeting all prereq's. This is a new install of LMS. Right at the beginning of the install process, i get this error and the install halts.
View 2 Replies View RelatedI got my modem about 3 months ago, I had no problems logging into my PSN account since last week. First, I was getting a DNS error. I was searching for a solution and I fixed the problem, the internet connection on my PS3 was working only for about a day. Later I started to get the 80130182 error, I tried to reset my modem and my PS3, I have unplugged everything and I plugged it back in, still didn't work. The internet connection on my PC works perfectly, only the internet connection on my PS3 doesn't work.
View 4 Replies View RelatedWhat could cause this log message and put the port in errdisable?
15w2d: %ETHCNTR-3-LOOP_BACK_DETECTED: Loop-back detected on FastEthernet0/22.
15w2d: %PM-4-ERR_DISABLE: loopback error detected on Fa0/22, putting Fa0/22 in err-disable state
15w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
I’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
When I run installation process I have received unexpected error:I have windows 2008 R2 x64. Antivirus is disabled and I have administrator privilege.
View 6 Replies View RelatedError : compressed image checksum is incorrect 0xDC5C5348 Expected a checksum of 0x066C5349I have uploaded a new firmware but same issue after booting, I have check the MD5 checksum in the image and Cisco and they are matching and verified, what could be the reason for all of this ??
View 2 Replies View RelatedOur customer is try to make a configuration by web interface menu:
Admin > Collection Settings > Inventory
After select the menu below they always received this message:
Error in starting acquisition: unable to connect to server
I am having trouble with gathering inventory for 7206 XVR devices. I got this error:
RICS0001:Internal Error,unable to process the collected data from the device
How can I make the inventory work for these devices ?
Here's an excerpt from IC_Server.log:
[ Tue Nov 29 16:24:53 CET 2011 ],ERROR,[Thread-31],com.cisco.nm.rmeng.inventory.ics.server.InvDataProcessor,458,SQL Anywhere Error -193: Primary key for table 'MemoryPool' is not unique
[Code].....
Having issue in applying package updates in LMS 4.2.3?
I am getting an error whether going via the GUI or CLI. The key issue appears to be (according to the PSU.log):
[ Sat May 11 16:41:25 EST 2013 ] ERROR [PsuPkg Resolver : pick Unselected BasePackages] :
Consistency check failed for base package SharedSwimRtr800(2.2)
I have the version 2.0.1 of SharedSwimRtr800:
327.SharedSwimRtr8002.0.1SharedSwimRtr800 device package
And I can't seem to find 2.2 anywhere in the downloads section for LMS 4.2
We need SQL-Connect to DB-Tables, as some "self-written" perl-scripts try to collect data.Are there any steps necessary to enable access to DB-Tables (and Views) ?
View 1 Replies View RelatedOn ACS 4.2.0.124 version installed on Appliance 1113.We are getting error code as "Internal error" and also "Enabling Tacacs+ is not allowed for this Access Server" while client authentication.
View 5 Replies View RelatedI have an 5510 ASA with 804 IOS. In that installed anyconnect (anyconnect-win-2.0.0343-k9.pkg) version. But when i am going to connect it from https:// I am getting the below error. So as a work around i tried to install anyconnect-win-2.5.6005-pre-deploy-k9.msi at my laptop and try to connect from https:// i am able to connect.
View 4 Replies View RelatedCant find the speeking result/cause of 4 and 1 in the example below, that are defined as enums in the MIBs normaly. Where can I access the result of "snmptranslate -M<MIB-dirs> -m ALL -Td <ps-status/test-oid>" if this is implemented in LMS overall? What are the OIDs from Cisco's ps-status/test, if the translation of MIB-enums is not implented?
Event_Description
StateNotNormalDevice IP
x.y.z.1Device Type
Switches and HubsFault Last Updated At
06-Nov-2012 16:12:49Component
[code]....
%ASA-3-305005: No translation group found for tcp src inside:211.155.169.186/1433 dst outside:42.121.87.89/6000, I found this error ,but the IP 211.155.169.186 is public address. I check the configuration but didn't find any information about this address.I don't understand why src is inside? How can I solve this error?
View 1 Replies View RelatedI am facing a problem with my LMS 3.2 server. Suddenly I found there is no device reflecing in common services-> device management as well as RME also. I restarted LMS services, server multiple time, reseted casuser, demoted the server from ACS mode to local mode but no luck. However in "dcrcli" i can see all devices and exported all devices to CSV file.
After this I restored from a backup 3 month old when devices were reflecting under common server and RME device management. this also not resolved the problem.
I uninstalled LMS, performed system cleaning and reinstalled LMS 3.2. Then I imported the devices from CSV file i had. Now also the problem not got resolved . I can see devices in dcrcli but none of the device is reflecting under device management of any module.
In Dcmaservice.log i found the error" ERROR,[main],com.cisco.nm.rmeng.config.netshow.server.admin.NSCommandSetManager,getAllCommandSet,8661,Invalid MDF data file:D:/CSCOpx/lib/classpath/com/cisco/nm/cwcs/mdf/mdfdata.xml"
Hence I restored teh mdfdata.xml file from another server. However now i can see the following errors
1) in common service -> software center -> device updae -> device count are 0 for all module
2) no device is reflecting under any module
3) one progress i saw when tring to add any device if selecting device type, it is showing me the list of device type along with OID. before restoring mdfdata.xml it was also not comming.
I am using ASA 5505 with firmware 8.2(2). My ISP uses PPPoE as a WAN connection protocol. There is a problem with getting PPPoE session started on my ASA 5505. The debug output says that after negotiation of PPP-authentication protocol ASA receives a PADT packet from ISP’s concentrator. To get more information I captured all packets on outside interface with WireShark. Packet-dumps (in .pcap format) are attached in this post. I have tried all possible combinations of PAP/CHAP/MSCHAP values in “vpdn group MYGROUP ppp authentication” command. If you take a look at the packet-dumps you can see, that in case of “PAP” – ISP’s concentrator rejects negotiation (PAP is not supported by my ISP). In case of CHAP/MSCHAP (that ARE supported by my ISP) – ASA acknowledges the using of MSCHAP v.2 PPP-auth protocol, which is actually not supported by it…
Judging by MAC-addresses of ISP’s concentrators it is visible that Cisco’s equipment also is used.
The questions is: Why ASA acknowledges using of unsupported ppp-auth protocol during negotiation and what I need to do to resolve this issue? (ISP’s support says, that they cannot change PPP-auth protocol negotiation order. Also they says that I need to contact with manufacturer of my equipment).
I try run Fault monitor feature in LMS 4.0, but I got error like this picture :
View 3 Replies View Relatedim trying to install Cisco prime LMS 4.2.3 for Windows 2008 R2 standard x64.however i have received this error message.
----- end of Dependency Handler Log File
-----Dependency Handler Errors
ERROR: csjre not found
ERROR: Component csjre is not found.
cdone : depends on :csjre
----- end of Dependency Handler Errors
[code]....
I have a ASA 5510 behind a 2911 router. I've trying to configure a remote access and site to site vpn tunnel. I've started on the remote access, and I have it setup, but I'm getting this error message with trying to authenicate from the VPN client (412 error)?
Nov 11 09:52:45 [IKEv1]: IP = 68.51.100.192, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 428
Nov 11 09:52:51 [IKEv1]: Group = tfx-tg, IP = 68.51.100.192, Duplicate Phase 1 packet detected. Retransmitting last packet.
[code]....
I configured ACS 5.3 and added AAA clients with TACACS+ server and shared secret key as cisco123. i did the below config on switch also. when i try to authenticate login with ACS it does not respond. Find the configuration and debug output.nd
In debug output it gives ruser and rem_addr is null. i did not understand why .
I am able to ping to ACS server and i used telnet 192.x.x.10 49 and it gives the proper output.
aaa new-model
aaa authentication login default group tacacs+ local
!
tacacs-server host 192.168.60.10 key cisco123
tacacs-server directed-request
ip tacacs source-interface Vlan172
We are getting the below mentioned error while installling Cisco Prime LMS 4.2.1 evaluation version on WIndows 2008 Enterprise R2.We tried installing on a high end VMware server .Prerequisites are all taken care by us.We are getting a LMS installation abort log saying that Swap space is not configured properly even after increasing the Paging size to 32 GB.Our physicalmemory is 16 GB.Hard drive has 2 partitions,one is 35 GB and other is 200 GB.
View 3 Replies View RelatedI am constantly getting error on UC520W Wifi from last Night, I am not getting with this error. What is the cause of this error, or is there any issue on UC520. [Code] .........
View 12 Replies View Related