We bought the ISA-570 for the same reason. On the literature it says that 5 ports are programmable for WAN ports but I can not find any configuration guide or documentation on how to configure these ports. We are already using WAN1 and WAN2 but want to program the programmable ports for additional wans.
View 3 RepliesI have a Cisco 1841 router with Fa0/0, Fa0/1 and Se0/0/0:0 interfaces. Fa0/0 is facing the LAN. At the moment WAN interface is Se0/0/0:0. It has following configuration:
View 5 Replies View RelatedHow i can configure the SFP Ports on my 4500 SERIES CHASSIS with other SFP ports on the connecting switch. I want to connect 15 switches via GLC=SX=MM to my 4506E sfp card.
View 4 Replies View RelatedI'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
I have WLC 2504 controller and six access points AIR-LAP1042N. I reading Cisco 2500 Series Wireless Controller Deployment Guide url...trying to set up along the lines.
It is also possible to have multiple AP-managers in a different subnet than the management interface. However, in this case, it is recommended that you disable the AP-manager from the management interface and create another AP-manager interface on different physical ports in a different subnet than the management interface. All multiple AP-managers in this scenario should be in the same subnet.
I maping management interface on physical port 1 and disabled ap-manager on it. Set up 192.168.7.0 subnet with non tagged vlan. This iface/port I want to use only for access to WLC web-interface. Then I create dynamic interface ‘dynamic1’, map him on port 2, enable ap-manager on him, and set up 192.168.110.0 subnet with vlan 10. Then I tryed map wlan1 to this iface, but I can’t because in the choice was only management iface to map wlan1.
There is three dynamic interfaces on same subnet and vlan, in example above. But when I try to add dynamic iface with the same vlan/subnet as an existing dynamic interface, I get an error, and can’t adding.
I am moving from ASA 5505 to ASA 5515 because we are maxing out the number of connections that the 5505 can handle. The 5515 runs version ASA 8.6(1)2 and ASDM 6.6(1) and the 5505 version is ASA 8.2(5) ASDM 6.4(5). On the 5505 I used e0/0, 0/2, 0/4 and 0/5 as outside port with teh switch ports feature but there is no switch port feature on the 5515. I have tried to set the ports individually to numerous public IP addresses that I have but I get an error that they subnet is already associated with another interface. How do I replicate the same setup on the 5515?
View 3 Replies View RelatedI have an ASA 5505 running 8.4.4.1. I've configured three WAN interfaces and have assigned failover on one of them (we have two ISP's, and a total of 3 static IP's in 3 different subnets). I've noticed that all the traffic is flowing through only one of the three interfaces, but I need to allow incoming https traffic on the second WAN port so I can access our Exchange server (we already use https on the first WAN port to access another server).
[code] WAN1 is the default outgoing route and we've configured several incoming services on it (smtp and https for example) and appears to be working properly as mail is coming and going and users can access the RDS gateway.I need to configure WAN2 to accept https traffic and send it to our Exchange server to enable OWA (webmail) access.I've configured the same Access and NAT rules on all three WAN interfaces for smtp (but I suspect only the first one is currently functioning at this point, I'll test it next chance I get). I thought all I'd have to do is configure an access and NAT entry on WAN2 (same as on WAN1), but direct the traffic to the OWA server instead of the rds gateway server, but it is not working.
In the realtime log I can see that it appears to be receiving the traffic on the WAN2 IP, but seems to be passing this through to the inside via the WAN1 interface.
I have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
View 8 Replies View RelatedI have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View RelatedHave our public IP address space masked on /24 at our Internet Router. The router portion of 3845 connects to Internet, while the internal switch connects to my internal network and seeds it with the public address space. The switch had a port configured no switchport (L3) with an ip address with /24 (ie 67.63.145.1 /24) this connects to internal IPS/IDS then to Firewall which NATs to internal, then packet shaper, web filter etc etc etc. I need to test my ISP speed so I need to "break in" to the link between the switch and the IPS/IDS. I figured I could configure another port on the switch on the 3845 but my problem is the port to my network is routed and is masked on entire /24. I tried to configure a port on VLAN 1 and give myself an available address in the L3 address space and this did not work (figured it would not but gave it a try)
Any way to get two ports configured to use the same subnet while one is a L3 routed port and the other is just part of that layer 3 routed network?
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies View RelatedAs per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
We have upgraded our gateway router from a Cisco Linksys RVL200 to a Cisco 861, this is a big jump from a GUI driven system to IOS CLi and i'm having issue finding my feet. I tried the Cisco CP system but it didn't work so I'm going to configure it with IOS commands. I wish to replicate the current configuration on the 200 with the following setup.
I have created a DHCP pool but i am unable to configure the FastEthernet ports to hand out address automatically, the pool is called USERS with range 192.168.1.30 -> 192.168.1.253.How do I work out the client-identifier for a DHCP client, I don't want to plug this into the network and manual reconnect all the PC's just to get the ID then make a static route.
Can i configure access ports into port channel on Nexus 7K switch.If possible then provide the complete configuration.....
View 2 Replies View RelatedIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View RelatedI have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies View RelatedI've been having a lot difficulties to get Cisco RV042 v 3 run on both WLAN ports. I've tryed in Smart Backup Link and Load Balancing .... nothing.What I want to do is:
1 web server in LAN lets say IP 192.168.15.2
1 dns server in LAN lets say IP 192.168.15.4
I want to have the router running as Smart Backup Link in case one of the internet connections fails (I will say that the DNS server handles most of the domain names on the web server so it needs to be publicly available as well, and the main domain name of the web server is managed by independent DNS server somwhere in internet, so it has mechanism that can be use to change the entries let say DNS round robin way).
1. WLAN1 with PPPOE and WLAN2 with static ip by the second provider LAN fasion, ports forwarded to the web and the dns servers - NOT accesible. Router firmware latest version 4.
2. WLAN1 with static ip by the second provider LAN fashion, network normal operating but cannot access the server on port 80.
I'm using a WRVS4400N and have all the proper ports open as well as the corresponding ones in the windows firewall. I've tested this with multiple port checkers online, such as grc.com. I've even go so far as to put one computer on a dmz and turn off the firewall on others. I've tested multiple ports on different computers. As well as from different remote gateways (other people's computers) just to see if it was a loopback problem.
I have the latest firmware installed and have done this from a clean install as well. This problem won't go away. My addy is nbcr [dot] dyndns.info if you'd like to have a test yourself and see that 118 is indeed closed.
I have an extensive computer repair background and run my own shop repairing computers, however networking is my weak area. Oh and its version 2.
we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.
View 2 Replies View RelatedHow do FPS's open UDP ports without needing to configure the router to forward them?I never have to forward ports from my router to my PC. Every game i have somehow manages to open the UDP ports it needs without me having to configure my router. Yet when i check to see if those ports are open (prior to starting the programs) they always come back as blocked or closed. Now I'm currently working on a UDP Internet program and need to know how to do the same thing - open ports on a router without having to make the customer configure their routers. I'm THINKING that other programs start with a TCP/IP connection on the desired port and that opens the UDP port. Is this the answer or is there another method used?
View 5 Replies View Relatedhow to forward ports using routers
View 2 Replies View Relatedto access VOD database i must open three ports on the router - not sure how to
View 3 Replies View Relatedwe would like to get Internet from the new router and have it go through a second (old) router on one port and another wired connection on another port. Currently, when we connect the old router to a port, no traffic goes through and dns cannot be resolved.
View 1 Replies View RelatedWe are looking to possibly purchase 2 RV042G routers. The main goal is to tie 2 sites together (via the internet) utilizing the site-to-site VPN feature.
Here is where it gets a little tricky. Since this device has 2 WAN ports, is it possible to assign a seperate IP address for each from our ISP? Then, what we would like to do is assign a couple LAN ports to have the traffic flow through WAN1 and the other LAN ports to flow through WAN2. The LAN addressing can be on the same subnet or seperate.
I am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
I am trying to add a couple VOIP phone units that do not have their own router. They are designed to run of the existing router and have three ranges of UDP ports opened up. They also do not advise using internal (private) statics on the phones. So what they are asking for is three different ranges of UDP ports to be opened up to all behind the router?
I cannot figure out how to do this (or if it is possible) with a RV016.
I have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
We have a single HP 2810 switch being used for an iSCSI SAN.We want to replace it with dual higher end switches.But we've got another SAN to also setup now - Dell Equallogic PS6010E - that has 10gb iSCSI SFP+ ports.Can the 4 x SFP+ uplink ports on the Dell PowerConnect PCT5548 or the HP 3800-48G-4SFP+ switch be used for just the 10gb iSCSI, while the other 48 handle the 1gb iSCSI?We were told the uplink ports don't have buffering, making them bad ports for iSCSI traffic and only useful as uplinks to another switch.We only need 8 x 10gb ports (4 for 2 servers, and 4 for the Equallogic SAN), so if the above would work, it would probably save us $10,000 from having to buy a separate 24 port dedicated 10gb switch to handle it.
View 5 Replies View Relatedhow can I block multiple ports on only 1 IP Address while not blocking those ports on other IP Addresses. I am using a Netgear WNR2000v1 which assigns the IP Addresses to each device.
View 1 Replies View RelatedI currently have 1 cat 5 jack at my tv/entertainment area and will be needing additional jacks to add gaming consoles,streaming video player and internet ready tv at the same location.The current jack installed at that location is coming from a D-Link 8 port Gigabit switch installed in a different room.The switch is at capacity,all ports are full,so no additional availability there.My question is how to expand port availability at the entertainment area.Is it possible to put another switch or hub at that connection?Would there be a conflict with cascading a switch from one to another? I have a 25 meg fiber optic incoming service,so there is plenty of speed and bandwith available to handle these componets.
View 1 Replies View Relateduplink port is already being used for a wireless dlink router.....want to add wired ports via a second router
View 1 Replies View RelatedI am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.