What are the SNMP port descriptions relate to on the SRP527? There is nothing in the administration guide and some of the ones that appear up don't make sense.
I think I have worked out a few by elimination but I wanted to confirm a few ...
Trying to configure an SRP527 to work in conjunction with a 3560G switch.My local subnet on the 3560 is 172.23.x.x.The subnet on SRP527 is 192.168.x.x Every thing can ping each other, except I just cannot get any internet access from 172.x through 192.x and out..? Does the SRP527 support this?
View 5 Replies View RelatedI would like my SRP527 router to manage 2 VLAN. 1 for my whole LAN and employees WIFI connections, another one for external clients to access Internet by guest WIFI SSID.
- I have this Cisco SRP527W router acting as a gateway between my LAN and Internet.
- I have a second router used for VPN connections between my LAN and 2 external agencies.
- My LAN is using 192.168.0.0 / 255.255.255.0 network
- External Agence 1 is using 192.168.1.0 / 255.255.255.0 network
- External Agence 2 is using 192.168.3.0 / 255.255.255.0 network
The Cisco Router is using 2 VLAN :
-VLAN 1 (LAN port 4 and SSID 1) -> 192.168.0.254 / 255.255.255.0
-VLAN 3 (SSID 2) -> 10.33.0.254 / 255.255.255.0
The Cisco router is using 2 static routes :
- Agence 1 : 192.168.1.0 / 255.255.255.0 -> Gateway 192.168.0.249
- Agence 2 : 192.168.3.0 / 255.255.255.0 -> Gateway 192.168.0.249
The VPN router for external agencies is using 192.168.0.249 / 255.255.255.0.
When the SRP527W router has intervlan routing enabled, everything is working. I can ping my external agencies. However, external clients using guest WIFI can also ping my internal LAN. Disabling intervlan routing separate VLAN 1 and VLAN 3 properly, but i can't ping my external agencies anymore and i don't know why ?
Behind my Cisco router :
- 1 HP Gigabit switch (servers, VPN router are connected to it)
- 2 Switches (HP and Accton) both linked to the gigabit switch and where all my clients are connected.
No trunk link and vlan are defined on my switches.
I have noticed that I have to reset the power on my srp527 more and more often, at first I thought it may be a glitch with my service provider but this is now happening more and more regularly. The internet just goes off, the network still exists and all the lights remain on (both adsl lights stay on) all the computers on the network (3 computers) cannot access anything on the net. A simple power off/on of the router restores everything but surely you do not need to do this everyday?
Firmware version. 1.01.09 (001) Apr7 2010
Can any provide me with the SKU's and pricing of the Broadband Access Center 4.2 Is this the correct version to use with the SRP527?
View 1 Replies View RelatedI need to know it the adsl router SRP547w or SRP546 permits to set class B subnetting ( or class A) on the Lan interface. I read the model SRP527 has a limitation to set ip address on the lan interface but I did not find any information about 547 or 546.
View 0 Replies View RelatedI'm trying to move from a faulty SRP527 to SRP 547 - I tried a Restore from Backup, but it doesn't work.So start from fresh, and I'm having an issue trying to add a 2nd SSID to a VLAN...
I keep getting the error:
"FAILED! SSID 2 has joined another VLAN"
Except it hasn't... its not assigned to any VLAN...
I'm trying to disable/enable ports via snmp v2 on a Cisco SG500-52P-K9-V01 switch. The communties are setup properly and I even have successful snmpset commands which when queried display that the action was complete. The issue is that when I disable the port via snmp the device on that port does not drop offline. This is a PoE port with a device powered over PoE so I'd expect the port to disable but also the PoE to turn the device off - neither happens.
Any experience with port management on this device? I also noticed the interface IDs (for port 1 for discussion) are 1, 101, 201 etc. I've tried setting on 1 and 101 only but the results have been the same and what were mentioned above.
Is there a way to send an SNMP trap form the ASA when port 80 is trying to be accessed??
We use the ASA5510 and also use ScanSafe Web Security. Web Security is great but we find ourselves worrying if user has edited their Browser connection settings to remove the proxy settings that we push down using Group Policy. We also cut off the users ability to make changes to those settings but it interferes when I need to troubleshoot a special program that cant use a proxy server. It just makes it harder for me. The other thing is that Group Policy only works for IE. Google Chrome will inherit the system settings in IE. So we have Safari and Firefox as well as a lot of others to worry about not getting the configuration. There is also debate about limitting the use of anything but IE and FireFox.
Without laying down the law and getting all sorts of hate mail and death threats I would like to run ScanSafe in such a way as to make sure each user receives the Group Policy settings and that is all.
I would now like to just set up an SNMP trap on the ASA for ANY traffic that is trying to get to port 80. Either get in in my syslog server or have the asa email me directly. Scansafe sends the Internet traffic out on 8080 to the Proxy towers.
I could block port 80 outbound but again, I limit my ability to troubleshoot on the fly. I would have to break this every time I need to troubleshoot.
Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies View RelatedI've got an SG300-10 connected back to back (trunked) with a Cisco 3560X switch, across a fibre link and am seeing some big inconsistencies in terms of unicast data transferred across the ports between them.
During a night time window of 4am - 6am I run backups which involves a large copy of files, that almost saturates a GigE link - we can see from the 3560X end that the link is running at a bit over 800MBit/sec of throughput, sustained. The duration of this transfer is consistent with the size of the files being transferred (ie just over an hour, and is what I'd expect for a data transfer of about that amount). Back-of-the-envelope calculations indicate that the 3560X is measuring this data throughput correctly.
However on the SG300 end of the link, which is also being polled by the same application (Cacti), I'm observing spikey counts of only around 20MBit/sec during that window. These counters are very obviously incorrect - there's a huge amount more data moving across the port than that. The incorrect calculations are showing on both the trunk port out of the SG300 (uplink) as well as the interface where the NAS is connected in (which is an access port).
Cacti is polling the OID: .1.3.6.1.2.1.2.2.1.16.57 which translates to IF-MIB::ifOutOctets.57 = Counter32.I'm running version 1.3.0.62 but this problem is not new to this release - previous releases and 1.2 based releases also had this problem.
It looks like multicast traffic may be being counted correctly (that's only a suspicion though), however what I am certain of is that there is a very large discrepancy with the unicast traffic counts.Is this OID the correct one to be using for this switch?
i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedI am trying to setup VPN monitoring for a srp527w Cisco.This is my first attempt at this so "easy to understand" instructions would be a great, i have done some searching and its difficult to decipher relevant and irrelevant information based on my limited exposure to this technology.
View 1 Replies View RelatedIs there a way to ask the above switch how much power it's supplying to various ports?I've found some stuff in POWER-ETHERNET-MIB, but it's only the main power supply and the up/down status of the various ports.
It looks like what I want is
[URL]
but my SG500 tells me:
snmpwalk -v2c -cpublic serverswitch 1.3.6.1.4.1.9.9.402
CISCO-SMI::ciscoMgmt.402 = No Such Object available on this agent at this OID
I'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
View 2 Replies View RelatedWe have a Cisco ASA and recently purchased a cisco small business srp527 router. It is connected to our ADSL2 connection and is working fine. I have configured the device with an ipsec tunnel using an ike profile and the tunnel is created successfully with packets traversing the tunnel. However packets are being dropped intermittently, with no cause. The link is currently not being utilised, there is no load on the network however when I ping Google and any address subject to the rules of the tunnel i notice that a single packet is dropped every now and then.
View 0 Replies View RelatedI have recently managed to configure a setup where I have 2 srp527's one at office one at home.Have 1 fixed IP at the office and 1 fixed ip at home.I have configured the srp at work to be a vpn server and have configured the group and 2 user profiles. This allows me to have 2 concurrent sessions over the vpn to my office from desktop and laptop at the same time. Connections fire up perfectly no problems.From the desktop, I connect using vpn client with user profile 1 Once connected, I then connect to my workstation machine at the office using remote desktop.This gets me super fast access to office files and large spreadsheets without downloading the whole file over the vpn and is working perfectly.
If I then additionally connect from the laptop using the vpn client with user profile 2 the remote desktop connection drops.Disconnect the laptop connection, remote desktop comes back.Have isolated this to being 2 connections arriving at the srp at the office from the same external ip. If I connect my laptop to my phone as a hotspot rather than using my home LAN, both connections are made and remote desktop has no interruptions. Is there a way I can overcome this through re-configuration of the srp at the office or is this a limitation with the srp?
I am attempting to monitor bandwidth utilization of the WAN port for the RV180 via SNMP and I am getting strange results. If a 256MB file is transferred from a remote server (without compression), the ifInOctets counter doesn't increment by anything resembling 256MB:
$ snmpget -v2c -c public 192.168.1.1 IF-MIB::ifInOctets.5 IF-MIB::ifOutOctets.5
IF-MIB::ifInOctets.5 = Counter32: 365402138
IF-MIB::ifOutOctets.5 = Counter32: 32610053
[Code].....
I'm reasonably certain that the .5 interface is the WAN port based on the value of ipAdEntIfIndex.X.X.X.X, but even if that were not the case, none of the other interfaces increment by a value close to the amount of data transfered. SNMP monitoring of a WAP121 on the same subnet returns expected results. I can only assume that SNMP on the RV180 is completely broken.
The router has the latest firmware available (1.0.1.9). There is only one network connection and the RV180 is the default gateway for all internal hosts.
Is temperature monitoring via snmp supported on Cisco 2801 routers? when i perform a snmpwalk i donot get the associated value for the oids.
View 2 Replies View RelatedI am monitoring my WRVS4400N with SNMP and create graphs by MRTG. Problem is that data about traffic are strange, very low. I have 50 MB line but max traffic shown on graphs is about 8000 bits per second. Also the "shape" of graph does not correspond with real traffic.
View 1 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
We've come across an issue whereby the WAN port fails to light up with an Adtran Total Access 832 (via bonded SHDSL) unit.
Eventually the WAN port does light up after connecting and disconnecting it several times with the ethernet cable. However as a test I power cycled the router with the WAN cable disconnected and had a strange issue where the WAN light would constantly flash and show up in the web gui as being connected when in fact the Adtran Unit showed the device was not connected at all.
This is the second Cisco SRP521W router in place as the original one disconnects overnight without any load and a power cycle would fix the issue, but this replacement router disconnects during business hours (even worse for the customer) and power cycling does not bring it back online. We've adjusted the WAN port to 10MB Full on both devices and hope that it stays up. I am wondering if any has had a similar experience? Would this be a behaviour of a faulty unit or may it not be compatible with the Adtran Total Access 832 (via bonded SHDSL) unit perhaps?
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies View RelatedPort forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
Does the Cisco SB RVS4000 router support 802.1x authentication for the WAN port?
View 2 Replies View RelatedRecently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
I have a RV042 Dual Wan. Two internets balanced wow! who would've thought that the headaches were waiting patiently right down the corner.
I was working with a 2wire Gateway that came with my ISP. I was able to open the ports in order to have public access for my students and teachers to upload their work. All I had to do was to allow my server ip address to have access to different ports blocked by the ISP. I used [URL]
I bought the RV042 for various reasons like excellent content blocking, load balancing, quick vpn, among other. But I just can't open the port 80 while having having my two ISP connected with load balancing, not even while having only one modem connected.
I have resolved many issues using the protocol binding. I have tried everthing. I just don't undertand something.
Whenever I connect my server to my old router, "www.canyouseeme.org" tells me that my port 80 is open. Whenever I connect my servet to the RV042-DW, my port appears closed.
So it's not any OS issues.
I've tried:
- To forward the TCP 80~80 port to my server static ip address... but failed
- To enable UPnP function with the same port... but failed
- To configure the port triggering with the same port.. but failed.
- To disable the firewall.. but failed.
- To use transparent bridge in the WAN1 with my 2wire Gateway... but failed
- To set up an account in DNS.ORG already had one, everythings is in green.. but failed.
- To change the configuration in my old 2Wire Gateway router to allow a DMZ zone so all ports are public... but failed.
- To assign RV042 router ip address in my old 2Wire allowing that specific address to allow certain ports to be public... but failed.
I have the Firmware v4.0.4.02 from DEC/11
[URL]
I'd like to use load balancing with the RV042, but I have some devices that don't react well to not always using the same outgoing port (like a credit card machine, for instance). Is it possible for me to create some "rule" with the RV042 that an internal IP address will use a certain WAN port? And if so, when that WAN port goes down will the RV042 fail-over to the other active WAN port? I was able to do this with a Xincom XC-OPG502 (which is being replaced with the RV042).
View 1 Replies View Related