Cisco Switching/Routing :: 3750G 12S Clients Lose Connection After Restart
Jun 6, 2012
We have a 3750G 12S that is connected to its clients with 1000 Mb SFPs. On the switch is a simple Vlan all the ports are assigned to. The ports are auto-sensing gig connection speed and full duplex when I run the show interface command.What happens is that if a client workstation is restarted or shut down and powered back up, the client cannot reconnect to the switch unless we cycle the switch itself (power off and back on)I know only the very basics of switch configuring and finding it difficult to source any trouble shooting info on issues like this.
View 13 Replies
ADVERTISEMENT
Feb 18, 2013
I have a 3750g connected to a "core" switch stack of 7 other 3750g's via 2 GigE ports in a trunk. This is currently in a switchport mode access port- channel so only the default vlan data is sent over. Now we have a need due to physical location of these switches, to allow vlan20 (DMZ) from this 3750g to the switch stack. I will configure a few ports on the switch stack for vlan20 and they need to be able to talk to the stand alone 3750g.To do this I will change the port channel on both endpoints to
-switchport trunk ecapsulation dot1q
-switchport mode dynamic desirable
also making the appropriate change on the interfaces belonging to this trunk.My question is, now that its a trunk port that carries multiple VLANs, how much is the bandwidth reduced on that 2gbps link?I have a very active VLAN (10) on the stand alone switch, but on the core I'm not going to be assigning VLAN 10 to any ports. So does traffic from VLAN10 even come across the trunk (wasting bandwidth) if no ports on the core side are assigned to it? I really just need vlan 1 and 20 (for now).
View 11 Replies
View Related
Jan 20, 2012
We are a small business with about 9 Macbook pros and 3 PC's connected wirelessly to the router. The Mac-computers sometimes lose their wifi-connection to the router. When this happens they have to select the wifi network again from the menu, to reestablish their internet connection. For some of the clients, this happens about once each day and for others multiple times a day. The problem doesn't seem to appear on the PC's.
I have tried to solve the problem by making DHCP reservations for each computers MAC-address, but with no luck. I also tried to set the 802.11 Mode to 'Mixed 802.11n and 802.11g', and turning WISH off. I read that the connection can be disturbed, if other wifi-networks in the area uses the same channel, so I changed it to channel 3, based on a scan of the network, where 3 appeared to be the least used. The WPA Mode is set to 'WPA-2 Only' and Cipher type is 'TKIP and AES'
The Dir-655 is hardware version B1 and the firmware is 2.0.
View 13 Replies
View Related
Jan 22, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : UPC Hungary Ltd.
I can't able to recognize a system - all wifi clients lose connection. When this happens, the ping answer time rech the ~2000 times, then totally lose the connection, the SSID is dissapear - checking with my phone (android - wifi analyzer) and TL-WN822N USB wifi adapter (with the inSSIDer application). Meanwhile the cable clients and the WAN connections works fine, didn't experience anything.If I restart the wifi service with the hardware on/off button, it runs well for some time.This problem appeared when I used the two older official firmware too.
I tried the auto-chanel function width auto channel width, tried to manually set up one of the less interfered channels with both 20MHz and 40MHz channel width, but none of them bring the solution.The intresting thing is, if I change the router with an old D-Link DI-604, the signal is weak, but the wifi connection is stable, with the same TL-WN822N adapter.I tried to guarantee the router, but after two weeks, my reseller said, it looks ok, they - at the TP-Link service - didn't find anything.
View 7 Replies
View Related
May 5, 2013
I have two 2960s that periodically lose connection for just a few Seconds. If I run a continuous ping from a workstation the connection never drops but as soon as I kill the ping command I will start losing the connection again. All cables test fine tried different switch ports nothing seems to work. No errors in log file either.
View 6 Replies
View Related
Jan 15, 2012
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
View 1 Replies
View Related
Dec 4, 2011
I have two 5000. Uplinks are Vpc to nexus 7000 and downlink are connected to Esx host. When I reboot one 5000, some Esx host lose connection to the NetApp SAN (Iscsi and CIFS) for 10-16 seconds. This is enought to generate errors and event corruption on disk. The 10-16 blackout occur when the switch as reloaded.
My theory is that VPC interface comme up 10-16 seconds after the edge interface(ESX). This create a blackhole effect for ESX host.
View 2 Replies
View Related
Nov 4, 2012
I have an RV220W running firmware 1.0.4.17. I have a couple of wireless laptop users that connect to the wireless without problems, but frequently cannot access the Internet. They can always access local network resources, but for some reason when laptops are first powered up or are idle for a prolonged period of time, Internet access is lost. Wired clients never experience this problem and always maintain local network and Internet connectivity.
To get the laptops to access the Internet over wireless, we have to run a TRACERT command from the command prompt to a public IP address, and then all Internet access is restored.
View 2 Replies
View Related
May 10, 2013
I have a Nexus 5548 Recently restart itself for no reason I ran the command:
sh system reset-reason
----- reset reason for Supervisor-module 1 (from Supervisor in slot 1) ---
1) At 469203 usecs after Sat May 11 14:02:07 2013
Reason: Reset triggered due to HA policy of Reset
Service: eth_port_sec hap reset
Version: 5.1(3)N1(1a)
sh processes log details
Start type: SRV_OPTION_RESTART_STATELESS (23)
Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2)
Last heartbeat 6.09 secs ago
RLIMIT_AS: 189894144
System image name: n5000-uk9.5.1.3.N1.1a.bin
I've been searching in Google/Cisco about the eth_port_sec hap reset and cannot find any reason, just something about the same error but in different technology:
[URL]
CSCub36000 #SNMP polling on eth_port_security objects no longer causes an eth_port_sec hap reset.I just to want to be sure, is the same reason...Or do you know something than can cause it on a Nexus Switch?
View 4 Replies
View Related
Mar 21, 2012
I am running those modules in my Cisco 6500 chassis and having lot of connectivity issues. I lose network connectivity every 5-6 day at around the same time. I have (2) C7000 Chassis with HP VC-Flex 10 Modules connected via 20Gb LAB to each Cisco Cisco 6513 Switches. However, the OA Modules on C7000 are connected via 1Gb uplink to either 6548 and 6148 modules. I beleive this is causing the netwok connectivity issues.What modules would be recommended to replace 6548 and 6148 who only meant to be used for 1Gb desktop connectivity, and not for Server Farm.
When you use either the WS-X6548-GE-TX or WS-X6148-GE-TX modules, there is a possibility that individual port utilization can lead to connectivity problems or packet loss on the surrounding interfaces. Especially when you use EtherChannel and Remote Switched Port Analyzer (RSPAN) in these line cards, you can potentially see the slow response due to packet loss. These line cards are oversubscription cards that are designed to extend gigabit to the desktop and might not be ideal for server farm connectivity. On these modules there is a single 1-Gigabit Ethernet uplink from the port ASIC that supports eight ports. These cards share a 1 Mb buffer between a group of ports (1-8, 9-16, 17-24, 25-32, 33-40, and 41-48) since each block of eight ports is 8:1 oversubscribed. The aggregate throughput of each block of eight ports cannot exceed 1 Gbps. Table 4 in the Cisco Catalyst 6500 Series 10/100- & 10/100/1000-Mbps Ethernet Interface Modules shows the different types of Ethernet interface modules and the supported buffer size per port.Over subscription happens due to multiple ports combined into a single Pinnacle ASIC. The Pinnacle ASIC is a direct memory access (DMA) engine that transfers packets between back plane switching bus and the network ports. If any port in this range receives or transmits traffic at a rate that exceeds its bandwidth or utilizes a large amount of buffers to handle bursts of traffic, the other ports in the same range can potentially experience packet loss. The buffer assignment on these modules is documented in Buffers, Queues & Thresholds on Catalyst 6500 Ethernet Modules.A SPAN destination is a very common cause since it is not uncommon to copy traffic from an entire VLAN or multiple ports to a single interface. On a card with individual interface buffers, the packets that exceed the bandwidth of the destination port are silently dropped and no other ports are affected. With a shared buffer, this causes connectivity problems for the other ports on this range. In most scenarios, shared buffers do not result in any problems. Even with eight gigabit attached workstations, it is rare that the provided bandwidth is exceeded.
The switch can experience degradation in services when you configure local SPAN in a switch, especially if it monitors a large amount of source ports.
This problem remains if it monitors certain VLANs and if a large number or ports is assigned to any of these VLANs.Even though SPAN is done in hardware, there is a performance impact since now the switch carries twice as much traffic. Since each linecard replicates the traffic at ingress, whenever a port is monitored, all ingress traffic is doubled when it hits the fabric. The capture of traffic from a large number of busy ports on a linecard can fill up the fabric connection, especially with the WS-6548-GE-TX cards, which only have an 8 Gigabit fabric connection.The WS-X6548-GE-TX, WS-X6548V-GE-TX, WS-X6148-GE-TX, and WS-X6148V-GE-TX modules have a limitation with EtherChannel. For EtherChannel, the data from all links in a bundle goes to the port ASIC, even though the data is destined for another link. This data consumes bandwidth in the 1-Gigabit Ethernet link. For these modules, the sum total of all data on an EtherChannel cannot exceed 1 Gigabit.
View 5 Replies
View Related
Dec 12, 2012
I have an sg300-10 unit. I have recently swapped it into my LAN network to replace an aging switch that was exhibiting problems.
The SG300 is reporting near constant 100% cpu load with 11pps input. there are only 3-4 active ports on the switch at a given time. One of those ports does lead to my router and another switch with another half dozen devices.
By itself this doesn't concern me overly much, but I have found that the SG300 is occasionally freezing up for about 20 minutes then restarting. Syslog and SNMP traps don't appear to provide any hints as to what is going on.
I have tied my switch into my monitoring system (packettrap MSP, so if there is something I should be watching that I am not, that would be good to know). I am still troubleshooting getting all the monitoring functions working as well.
So, I have some questions there as well, which OID should I be monitoring for CPU utilization?
View 3 Replies
View Related
Mar 21, 2012
I got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
View 4 Replies
View Related
Mar 4, 2012
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
View 7 Replies
View Related
Mar 12, 2013
I know only one method to restart Cisco switch through Telent using command " RELOAD". How can we restart Cisco 2960/3560 switch phyically....can i use mode button to restart cisco switch ?
View 11 Replies
View Related
Dec 25, 2011
i have facing problem in my Cisco Secure router 2811. It hanging every 5 to 10 minutes and restart. IOS of cisco router is 12.4 ipsecurity. I have attached the error log and configuration file of my router. Kindly see the log and let me the problem in my router.
View 9 Replies
View Related
Nov 8, 2012
I have a couple of 3750G-24T-E switches running IOS 12.2 I would like to upgrade to IOS 15.x. Is this possible? Where do I find some information on the required licenses and costs? I must admit that the cisco search function did come up with a few pages but i was not able to extract the required information. I have not used the new software activation features yet.
View 1 Replies
View Related
Jun 7, 2012
I've got a requirement to do Inter-VRF routing (need MP-BGP) using a private AS Number on a stack of 7 x 3750G's, my question ultimately is the performance overhead of doing such a change.
The stack will have no more than 300-400 routes even with the duplicates invoked from doing VRF leaking so I can't see much of an issue myself, we already have 2 VRF's and OSPF running in each VRF just don't have MP-BGP to do the VRF leaking.
Ultimately there will be about 4-5 VRF's (I know there's a Software limit of 26 VRF's on a 3750G).
View 3 Replies
View Related
Jun 21, 2011
We are using WS-C3560G-48PS connected via UPS power supply. Whenever raw power supply gets fluctuates few of the IP phones (Alcatel) gets reset although switch is remain up and running. We checked the same by disconnecting the raw power supply but we didn't found any packet loss from the node which are connected through this switch. But few IP phone gets reset. What could be the reason
View 2 Replies
View Related
Aug 12, 2012
I am setting up a Cisco 1941 series router for our department in Denmark. As we quickly relised we had to reset the router to it's defult settings. As we comunicated with the router thorugh HyperTerminal, the router asked me to restart. After we did so the router only sends encrypted messages wich is unreadable. We neither get any respons in the terminal when we try to write commands back to the router.We have tried to use different terminal programs as well as the USB port on the router.
View 4 Replies
View Related
Oct 2, 2012
I am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
View 3 Replies
View Related
Oct 8, 2012
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
View 2 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
Nov 20, 2012
have 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
View 4 Replies
View Related
May 26, 2011
I have a 3750G and bought a new 3750X. It possible to stack these two together?
View 5 Replies
View Related
Nov 18, 2008
I have a 3750g on which I am trying to configure the ip policy route-map command on each of the vlan interfaces. However after entering the command it does not appear. I'm not sure what to do at this point. I have changed the SDM template to routing and I am running the IPServices image.
View 2 Replies
View Related
Jan 23, 2013
I have just received a new Cisco 3750G Switch from my parent company. When attempting to install the switch, I discovered that it will not boot to CLI, only to the bootloader. After using the command boot, the switch attempts to boot the most current IOS version, but fails, stating "error loading XXXXXXXXXX.bin".
Obviously, I just need to get a functional version of the IOS onto the switch to boot, but the problem is exactly how can I do that? All (or most) the commands with which I am familiar are unavailable in the bootloader, so all methods known to me fail. Is there a simple way (maybe using the copy command?) to put the .tar or .bin file onto the flash?
View 2 Replies
View Related
Sep 17, 2012
I am trying to create an ACL that walls off a VLAN and only allows it to the internet. This is on a 3750G, currently the 3750G I am attempting this on is in a stack. I have another 3750G that is a standalone.
The first way I attempted this was to create two access-lists: access-list 101 permit tcp 10.249.1.0 0.0.0.255 any eq 80 access-list 102 permit tcp any 10.249.1.0 0.0.0.255 established
Let's call the 10.249.1.0 VLAN 2. I applied this to the VLAN2 interface, 101 out, 102 in. It didn't work. If I place a deny statement with nothing else, that works.
The second attempt was this: access-list 101 deny ip 10.249.1.0 0.0.0.255 any access-list 101 permit ip any any
I applied this to a VLAN I wanted to block VLAN2's traffic from reaching, let's call that one VLAN 3.
This lets all traffic from any VLAN (including the one I'm trying to block). If I remove the "permit ip any any", then all VLANs are denied. Which I understand is correct due to the implied deny all. What I don't understand is why it isn't applying the ACL to the specific VLAN.
View 3 Replies
View Related
Jun 2, 2013
I have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
1) Hold mode button & issue a reload after the lights start flashing
2) issue "Write Erase" then issue "reload"
3) issue "Write Erase", then issue "Write", then issue "reload"
4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)
5) issue "erase start" then issue "copy run start" then issue "reload"
Is there a special way to reset a StackMaster back to factory defaults?
View 6 Replies
View Related
Apr 22, 2013
I have one 3750X with C3KX-NM-10GT, I need to interconnect using stackwise to 3750G-24TS. The 3750X needs IOS 15.0(1) to use C3KX-NM-10GT, and the latest IOS for 3750G-24TS is 12.2.55. How can I interconnect them using diferent IOS?
View 2 Replies
View Related
Jan 29, 2013
I have a 3750G switch that can't detect another switch or be detected through its stack ports. I tried the recommended test; looping a cable between the ports and rebooting. I get the following message as the switch boots: SM: Detected stack cables at PORT1 PORT2. However, if I connnect another switch, it won't detect it and can't form a stack.
View 4 Replies
View Related
Feb 20, 2012
I'm trying to upgrade the IOS ver on a 3750G stack (2 switches), but the img on the switch is too old.The stack is running IOS c3750-i9-mz.121-19.EA1d.bin, and when I tried to upgrade to a newer version, I tried to go to IOS ver c3750-advipservicesk9-mz.122-35.SE5.bin since I need to enable ssh on the switch, but the switch did not reload.
Here's a prtscreen of the switch ver:
Cisco Internetwork Operating System Software
IOS (tm) C3750 Software (C3750-I9-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 05-Apr-04 22:40 by antonino
Image text-base: 0x00003000, data-base: 0x007CBC3C
[code]...
what IOS ver can I upgrade to that is not already deferred?
View 1 Replies
View Related
Jun 17, 2012
have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
View 2 Replies
View Related
Feb 7, 2011
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
View 9 Replies
View Related
