Cisco Switching/Routing :: Router 2811 Joining All Multicast Groups?
Oct 31, 2012
I have a switch 2960 with 15 multicast groups (for video) and now I am configuring a router 2811 to send two multicast groups to another network.But despite of there is no client sending join yet, the router is joinning in all multicast group, and because of that the router are not standing all the traffic. why the router is joinning in all multicast groups?How could I choose what groups router will join?
Router Config:
ip multicast routing
ip pim bidir-enable
interface f0/0
description Conected to Multicast Source Network
ip address 10.1.1.1 255.255.255.0
ip pim sparse-dense-mode
Any switch that supports 4096 multicast groups?I am working on a system that includes over a dozen catalyst 2960 switches. The customer has pointed out the 2960 switch does not satisfy the requirement to support 4096 multicast groups (even though it is more than adequate for the number of active multicast groups). It looks like the 3560 supports more multicast groups than the 2960, but is still far less than the requirement.
We're starting to share video across our network and would like to setup multicast to conserve at least some of the bandwidth. We have a broad mix of equipment (A Catalyst 6509-E at the core, a combination for Cisco 2691 & 2811 routers, and a whole lot of Catalyst 3500, 3550, 3560 switches at a hundred locations. Where would I begin? Would I need to define routing for the multicast IP addresses (224.0.0.0)? Would I need to setup interfaces & IP networks where each multicast device is located like I would for a new IP subnet?
i have a question about multiple TACACS Groups. I want to archive the following:
A Cisco 888 is managed by me and a Provider Support Team. Since we both want to access our own TACACS Server, i want to create two TACACS Groups. Is it possible to me, to bind a Tacacs Group to one Interface, and the second TACACS Group to another ? Means that our stuff is connecting to the LAN Interface FastEthernet0 that is applied to the SVI in V LAN 1.
The service technicians from the Provider are connecting to the external Interface or through a possible Lo. (another IP). I do not want to mix our 2 TACACS+ Server and theirs together in one Group. So have anybody tried this before ?
configured 2 EzVPN groups using a 2811 router, i am trying to do this but is not working i have another VPN working thru EzVPN but if i try to configure another group for another EzVPN client is not working and the problem is that the debug crypto isakmp say that Apr 3 08:45:25.802: ISAKMP:(1309): phase 2 SA policy not acceptable!
How is that possible? in my understand the EzVPN server will inject the the IKE (phase 1) and IPSec (Phase 2) parameters for the client and that's they dont need to negotiate nothing, is important to say that the EzVPN client is an ASA5505 with onlu DES encryption enabled, 3DES and AES are not available due to licensing reasons.
I’ve been trying a few days now to implement multicast routing on my home network in order to make airplay work between subnets. Specifically between an iphone and a hifi separated by different vlans. Failed, as I have no experience in multicast routing. we have a clean configuration and simple network which consists of two SVIs
I am trying to join a Cisco Catalyst 3560X-24T-L to an existing VTP domain, my question is what configurations should I do to this switch?I have already gave it a hostname, setup passwords, enabled telnet, created a management address on port g0/24.I would like it to be on VLAN 13, is this done from my server switch, or done on the new switch?
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
I have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
router 2811 has 2 files ios in flash Router#sh fla -#- --length-- -----date/time------ path 1 35202336 Mar 3 2008 16:12:28 +00:00 c2800nm-adventerprisek9-mz.124-8d.bin ... 13 59374168 Mar 5 2012 12:49:22 +00:00 c2800nm-adventerprisek9-mz.124-24.T.bin
151076864 bytes available (105431040 bytes used)
Router#
I try to make it load c2800nm-adventerprisek9-mz.124-24.T.bin
[Code] ...........
I did verif flash:c2800nm-adventerprisek9-mz.124-24.T.binit is ok
is it corrupted memory? how to fix it?and aslo with System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"it dos not show voice ports for WIC2-FXO in runn conf
I have working internet behind cisco 2811 on all vlans however upload speed is very slow and ftp server download is slow and times out, previously when directly connected to modem/router was fine? This is router config below:
Current configuration : 2229 bytes ! ! Last configuration change at 02:21:18 UTC Tue Mar 12 2013 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec
we have cisco 2960 switch which is connected to a cisco 2811 router. flapping issue between these two devices??
The following actions i have taken, but no result.. I have changed cables. have set speed to 100 and duplex full on both the interfaces but the interfaces are showing up up still not getting connectivity. same i have to auto on both sides still no result what configurations should i set to resolve this issue...?
I upgraded a 2811 router to the latest version and apparently everything went smooth. I reloaded and did a sh ver the IOS show the correct version, but the boot strap shows the old IOS. How can I change the boot strap to show the new IOS.
I have Cisco 2811 secure router in my network. Seven day before it has been hanging every 3-4 hour. i have updated "c2800nm-advsecurityk9-mz.124-17.bin" IOS in the router. After that it giving some error and every 7-10 hour network has been delay in LAN as well as WAN and not pinging.
In the existing network we have Cisco 2811 router connected to Corporate MPLS cloud. Cisco 2811 is connected to Catalyst 6509 switch(set based IOS with MSFC card). Along with that we have two Catalyst 5509. We are upgrading the access layer by replacing catalyst switches with Nexus 5548 & 2248.
For a purpose of testing I have connected 5548 & 2248. Created cPC and ether channels between two. SVI and HSRP configuredon 5548. I am terminating 2651 (test router) on 2248 port 101/1/1. On 5548 I have enabled EIGRP on vlans. I am unable to ping to 2651 from nexus switch 5548 and vice-versa. I can see both devices on CDP but I do not see eigrp neighborship formed.
What configuration should go in 2248 and 2651 in order to establish a connection between two? If test is successful then I will connect 2811 to 2248 during actual migration. I assume that in testing if it works for 2651 then it must work on 2811 router.
i have facing problem in my Cisco Secure router 2811. It hanging every 5 to 10 minutes and restart. IOS of cisco router is 12.4 ipsecurity. I have attached the error log and configuration file of my router. Kindly see the log and let me the problem in my router.
I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing ! ip vrf vpn2 rd 1:1 mdt default 232.1.1.1 route-target export 1:1 route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
I am trying to configure router on a stick with 2811 and 3750, but I just cannot get it to work - vlans are not getting propagated from 3750 to 2811: 3750:
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
I got the error in object when I try to add a new HSRP group in new vlan.All the HSRP group has the same HSRP group the 2.another way to provide clients's default gateway redundancy for each Vlan intead to use the HSRP?
I have started to use ip extended access-lists on several 3750X-switches to filter inbound and outbond traffic on the VLANs. But it seems that the use of object-groups is not supported, is this correct? Is it really no way to group different ip-addresses into groups and then use these groups in the access-lists?
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
I understand on older IOS codes If the same hsrp group number is assigned to multiple standby groups, it creates a non-unique MAC address. Is this true on newer codes like 12.2(52)SE for 3750 & 3560?
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled. In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4 Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2 Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
I am configuring multicast in a environment where I have a 4506 at each site (4 total) and a 6506 as the core. Each 4506 is connected via layer 3 to the 6506. I have a mix of 3560s, 3548s, and 2960s connected to the 4506s and the 6506 via layer 2 trunk
I have multiple multicast sources and hosts communicating at a time (multiple cameras sending video / multiple computers receiving video). So this is not a scenario where there is 1 sender and many receivers. This would be many senders (~50) and some receivers (~10)
I configured ip multicast-routing on each of the 4506s and on the 6506. IGMP snooping is on by default on the 3560 and 2960 switches. CGMP is on by default on the 3548 switches.
I set up PIM sparse-dense mode and IGMP version 3 on each of the layer 3 interfaces for the 4506s and 6506 where they connect and on each VLAN that is sending or receiving multicast. Multicast is working throughout the network, however I am looking to verify the configuration as I scale this out to more clients on the network.
#1 - Is it correct to us sparse-dense mode in this configuration?
#2 - Do I need to configure a rendezvous points using AUTO-RP? (ip pim send-rp-announce INTERFACE scope TTL). Not sure here if I need to designate this and what to choose. Right now I do not have this and it is working, but documentation seems to infer that I need to designate this.
#3 - Is there any other configuration settings I should be considering? I hard to find real world configurations of multicast as examples or people that know multicast routing well.
I would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1, Vlan 130 (192.168.130.x) Fastethernet 5.
Version IOS is : adipservice-k9 124-9.t1
ip multicast-routing
#int Vlan 130 ip address 192.168.130.254 255.255.255.0 Ip pim dense-mode #int Vlan 200 Ip address 192.168.200.254 255.255.255.0 Ip pim dense-mode
I used VLC for my test.When i connect source (224.10.10.10) and recever ( Udp://@224.10.10.10:1234), that's ok!But, source is on the Vlan 200 and reicever on the Vlan 130, is not good!I test with "sparse-mode", i have same problem.
while i am configuring a port on switch .The switch reloads.After reload the show version says,System returned to ROM by bus error at PC 0x458F6C, address 0x0,show version from the effected switch is,Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1).
I faced multicast routing problem - There is no multicast UDP stream toward host, although all igmp Joins/Reports/Leaves from the host are correct.
This is Cisco 7609 ip m route debug showing the situation: 369144: Nov 15 15:03:07.370 MSK: IGMP(0): Received v2 Report on Vlan176 from 10.XXX.XX.184 for 239.XXX.XX.46 369145: Nov 15 15:03:07.370 MSK: IGMP(0): Received Group record for group 239.XXX.XX.46, mode 2 from 10.XXX.XX.184 for 0 sources [code]....