Cisco VPN :: WRVS4400S Router To Fortinet VPN Connection
Jan 29, 2012
I created the VPN between WRCS4400N and Fortinet 111c and tunnel is up. When i am pinging my cisco subnet (10.0.20.0) from fortinet, its pinging. But when i am pinging fortinet (10.0.1.8) or any ip of this subnet from cisco router its not pinging.I have real IP on my Fortinet and dyndns on Cisco Router. The simple diagram is attached for my vpn network. I think its routing issue, i have to add route in cisco router but i don't know what route i have to add there in order work the vpn perfectly.
View 1 Replies
ADVERTISEMENT
Dec 29, 2012
We have done the site to site VPN between Fortinet and Cisco SA540. Everything is configured at both ends but the tunnel is not establised.
View 4 Replies
View Related
Aug 4, 2012
We are currently in a position to be needing an ASA series firewall. We currently have dual redundant Fortinet 300C's in place. The reason we are wanting the ASA series is the way we are designing our VOIP system is we will be utilizing the 9900 series cisco phones with the any connect VPN. We are also going to structure our BYOD deployment around the any connect VPN.
My first step is to find an ASA firewall that is comparable to the 300C's that we have now.
We have 350 "internal" clients on an MPLS network at 20 remote sites. All of the internet to these sites comes back to our HQ where the firewalls are located. The MPLS is 30Mbps to the internal and 15Mbps to the internet. The fortinets do web content filtering, traffic logging, DMZ separation, NAT, and we will replace our Juniper SA2000 VPN with the ASA firewall as well. We are looking at roughly 125 VPN clients.
View 1 Replies
View Related
Dec 12, 2011
My main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies
View Related
Jan 13, 2012
Often my router drops connection to all my devices. Multiple times a day. It's only for a minute or so, but it's annoying. I'm using a Linksys Wireless-N router (WRT160N) with WEP encryption. I'm running two Windows 7 laptops, LG BluRay player, Apple TV, Xbox 360 (Wired) iPhone 4, and a iPad 2. It doesn't matter if I'm browsing the web, watching Netflix, or playing a game, the connection gets lost. As we speak it happened again. I have no clue on what to do. I've reconfigured it multiple times. Firmware has been updated months ago.
View 6 Replies
View Related
Mar 14, 2013
Region : India
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
ISP : TataDocomo 3G
I am having problems with my TL-MR3420 router, it disconnects WIFI all the time. My ZTE MF 631 dongle gives me a strong signal and stable connection and rarely loses connecton when plugged directly into my laptop. With my MR-3420 V2 losses connection, duration only lasts for about 2 to 3 minutes. I have to power off/on the router and turn off/on the wireless button on the laptop to restore connection or manually disconnect in the web interface of MR -3420 and reconnect.
Even i tried the changing channel bandwidth and channel, still no luck. Router settings is pretty much default, expect security key. I have quite recently upgraded to the latest firmware but the problem seem not to have been resolved.
View 4 Replies
View Related
Mar 25, 2011
I just installed a 886 router. I noticed that the xDSL CD light is flashing... slow then fast. I am assuming the DSL line is not syncing up. How do I go about diagnosing the problem. I am connecting to an ATT dsl equipment.
View 11 Replies
View Related
Jan 21, 2013
A pen test has shown I have crackable transform set on my firewall. I can see the config this relates to and do have higher encryption available. What I dont want to do is remove it until I know my remote sites are not using it.does any one know a command that shows all the policies/encrption in use?
View 5 Replies
View Related
Jan 5, 2011
Recently i purchased Cisco 861-K9 router for my head office.
I have 2 offices (1 is head-office & other is Branch.). i have MPLS Connectivity between 2 offices.
i used 861-K9 WAN port for MPLS Connection.
My question is "is it possible to use the FastEthernet Port of 861-K9 router for connecting the internet Link ?"
View 1 Replies
View Related
Feb 20, 2012
I want to know which router can be used on 100mb cable connectionThe router will be using the connection from cable modem on bridge mode/modem mode with eth to routerI kind of have a idea looking at performance ratings but ppl have mixed opinions when you enable NAT and ACLs etc etc285129013825.
View 5 Replies
View Related
Mar 21, 2013
We have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
So my case is: computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382).
How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
View 4 Replies
View Related
Feb 7, 2011
I am facing problem when trying to establish VPN connection between ASA and 1841 router. Peer comes up but traffic is encrypt and decrypt. when assign route (ip route 192.168.x.0 255.255.255.0 fa0/0) to remote local subnet there is a traffic but one reply and one drop
ping from
192.168.y.62
-------------------------------------------------
Reply from 192.168.x.55: bytes=32 time=493ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=633ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=375ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=528ms TTL=127Request timed out.
[code].....
View 1 Replies
View Related
Jul 16, 2011
i just managed to config the Cisco 877 and send it to my client,when the client connect the router from his location the router can't make VPN connection to my HQ office,i can connect to the router using the external IP adress,i tried to reset the VPN tunnel but no avail,
View 3 Replies
View Related
Nov 9, 2011
I have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
View 2 Replies
View Related
Feb 15, 2011
I've to realize a VPN (ipsec) between 2 side that use a Router Cisco 1841, each one with its own public IP.The 2 side can ping each one with Public IP but the VPN are in DOWN's state.The schema is the following:
192.168.1.0/24 (LAN1) <-> Ro1 (X.X.X.X) <- VPN -> (Y.Y.Y.Y) Ro2 <-> 192.168.2.0/24 (LAN2)
the configuration of Ro1 is showed of following, the same configuration is present also in Ro2 but with different IP address
sh runBuilding configuration...Current configuration : 9808 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname TEST!boot-start-markerboot system flash c1841-adventerprisek9-mz.124-24.T.binboot-end-marker!logging message-counter sysloglogging buffered 51200 warnings!no aaa new-modeldot11 syslogno ip source-route!!! !ip cefno ip bootp serverip domain name test.itip name-server x.x.x.xip name-server x.x.x.xip inspect log drop-pktip inspect max-incomplete low 300ip inspect max-incomplete high 400ip inspect one-minute low 300ip inspect hashtable-size 2048ip inspect tcp synwait-time 20ip inspect tcp max-incomplete host 300 block-time 60ip inspect name IDS tcpip inspect name IDS udpip inspect name IDS ftpno ipv6 cef!multilink bundle-name
[code]....
so, of following the screen of the answer of these commands.
Ro1(config)# sh crypto session Crypto session current statusInterface: Serial0/0/0.1Session status: DOWNPeer: 81.21.17.146 port 500 IPSEC FLOW: permit ip 192.168.1.0/255.255.255.0 192.168.2.0/255.255.255.0 Active SAs: 0, origin: crypto mapRo1(config)# sh crypto map interface serial 0/0/0.1Crypto Map "VPN" 1 ipsec-isakmp Peer = Y.Y.Y.Y Extended IP access list 150 access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255 Current peer: Y.Y.Y.Y Security association lifetime: 4608000 kilobytes/86400 seconds Responder-Only (Y/N): N PFS (Y/N): N Transform sets={ VPN-SET: { esp-3des esp-sha-hmac } , } Interfaces using crypto map VPN: Serial0/0/0.1
View 14 Replies
View Related
Dec 26, 2012
I need some clarification if it is possible to do an IPL connection between Cisco 2801 (T1) to Cisco 1841 (E1) via Ethernet (2801) to Serial (1841).
I am unable to find any documentation about this and I need to connect our network to our overseas office.
Our side uses the 1841 router and our provider has set-up our E1 connection to be via Serial interface while on our overseas office uses the 2801 and will connect via the T1 card, which by the way does not have any serial interface ports just ethernets.
So far checking on how to configure this, I am unsure on how the connection will happen since the info that I got is that T1 does not have the option to hold an IP address (also unsure on this though). With this in mind and that the 2801 does not have serial interfaces, does that mean that IPL connection would be via the available Ethernet ports?
View 11 Replies
View Related
Sep 26, 2012
I have a RV042 VPN Router inside an ASA 5505 running version 7.2. I am attempting to connect from the outside to the RV042. I have read for 2 days now and tried everything I have found and had no success. I can connect from inside the network to the RV042 so I know that is setup correctly. I have found links on several posts to the official Cisco support documents but they make no sense to me. This is my first experience with a Cisco Firewall.
We also have a security camera network that we access externally and I have successfully set up the port forwarding for this. Here is my current running configuration. The inside ip address of the RV042 is 192.168.168.25. I had port 1723 forwarded, opened GRE, and have setup PPTP inspection. I have deleted the port forwarding at this point.
Result of the command: "show running-config"
: Saved
ASA Version 7.2(3)
hostname suite
domain-name hivermont.com
enable password vwiH3D2KQdqR57As encrypted names
interface Vlan1 name if inside
security-level 100
ip address 192.168.168.1 255.255.255.0
ospf cost 10
[code].....
View 4 Replies
View Related
Apr 27, 2011
I am running a Cisco 878-K9 Router, IOS 12.4(11)T1, as a Firewall with EasyVPNServer. The VPN Server was created with the wizard from the SDM.Everything works fine, BUT the VPN connections fail after about 10 minutes.
View 1 Replies
View Related
Jun 2, 2011
my problem is this:we have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
so my case is:computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382)How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
View 11 Replies
View Related
Dec 6, 2011
I have a Cisco 819 WAN Router (C819 Secure M2M GW (non-US) 3.7G HSPA+ R7 w/SMS/GPS).Software: Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.2(2)T, RELEASE SOFTWARE (fc1)
For dialing in at my Provider (T-mobile Germany), I use the following chat-script:
chat-script gsm "" ATZ "" AT+CGDCONT=1 "OK" "AT!SCACT=1,1" TIMEOUT 60 "OK" "ATD*99#" "CONNECT"
Dial-In is successful after Reboot.Now, i want to simulate a conenction fault, e.g. termination by mobile provider.So I used the command "clear int cellular 0".After that, The router can't dial in again.
Debug shows:
Dec 7 11:04:03: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down
Dec 7 11:04:14: CHAT3: Attempting async line dialer script
Dec 7 11:04:14: CHAT3: Dialing using Modem script: gsm & System script: none
Dec 7 11:04:14: CHAT3: process started
Dec 7 11:04:14: CHAT3: Asserting DTR
[code]...
Is the "clear interface cellular 0" the wrong way to test this, or why can't the Router reconnect?The only solution is a reboot, but that is not the best option. The router should automatically redial.
View 10 Replies
View Related
Jan 19, 2011
My computer is says there's no network cable plugged in when i have it plugged in to my smc router but when i plug it into my cable modem i get signal . Ive updated my drivers. my network cable is good i tested it.. all the other computers on the network see the router.
View 4 Replies
View Related
Feb 17, 2013
i have 3 buildings and some how want to connect all these up and have a specifications Building 1, floor 1, 30 users, floor 2 has 30 users,Building 2 30users, Building 3 30 user, Building 1 and 2 has cat 5 cabling. So what routers cabling etc. would I use to connect all these building
View 1 Replies
View Related
Jan 21, 2013
I currently have a d-link DIR-615E3 with the latest dd-wrt firmware (v24 from 2010-12-13). Everything seems to be ok when I boot up the router - with factory settings and unsecured wireless, I have an internet connection. When I enter the GUI, create a router username/password, everything is still fine. Then, when I create a wireless security password (WPA2 personal) I lose internet connection, and the only way to get it back is to do a hard reset of the router. This also happens if I change any setting within the ddwrt interface, not just the wireless settings. (I also have a linksys WRT54GL with ddwrt with absolutely no problems) My cable modem is a motorola surfboard SB5101U, ISP is comcast cable, running windows 7.
View 6 Replies
View Related
Aug 29, 2012
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 6109 Mb
Graphics Card: Intel(R) G45/G43 Express Chipset, -1265 Mb
Hard Drives: C: Total - 938406 MB, Free - 547304 MB; E: Total - 238414 MB, Free - 189947 MB;
Motherboard: Gateway, EG43M
Antivirus: Microsoft Security Essentials, Updated and Enabled
1. using Vizioxwr100 router
2. have a WD2500JB HDD (USB)
3. when HDD connected directly to pc, it can be accessed.
4. when HDD connected to router, router identifies it as WD HDD ON status PAGE...but
5. PC CANNOT see it in Win Explorer
the WD HDD is my network storage unit.
View 7 Replies
View Related
Jan 26, 2013
Since upgrading to windows 8 a few days ago my router keeps dropping my connection every few minutes . 4 other pc's in the house are fine. Mine has a wooden floor for the signal to pass through, my wifes which is fine has two walls between her and the router.
View 3 Replies
View Related
Aug 27, 2012
My TV Ethernet connection to my router, when streaming content from my laptop. When my TV is connected to the router via Ethernet cable and my laptop is connected to the router , O am able to stream media to the TV, but the TV often disconnects itself. I think the router is the problem because when the computer a connected directly (not using the router) It doesn't disconnect. Also another issue when the TV is connected to the router the computer will only connect to the TV if it is connected via an Ethernet cable, It wont through wireless.
View 4 Replies
View Related
Jul 16, 2012
My computer needs to be online i.e. directly connected to my cable modem. I have need to set up a wireless router too. I was initially thinking of buying a USB Ethernet Adapter and connecting a wireless router to it. I would then share my internet connection that comes into my computer the modem, with the network that my computer and the wireless router create.After looking at various modems online that have a USB connection, I am wondering if there is any wireless router can directly connect to my computer via USB and then share the internet connection with other wireless devices like phones and tablets
View 2 Replies
View Related
Apr 30, 2012
I have Verizon Fios. My laptop connects wireless to router and can get to the internet. The laptop can also work wired to router. My desktop connects to router OK, but can't get to internet. I reinstalled IE8. I can put in the router address and connect to router. I can ping between laptop and desktop. IE says it's waiting for whatever address I type in, says Done, then goes waiting for [URL]. It always comes back either The address is not valid, or Internet Explorer cannot display the webpage.
View 3 Replies
View Related
Dec 23, 2012
i have a big network of about 50 computers and have only one internet connection .i have applied for other connection so that if some time i link ll be down we can still work on other. how to configure other line on the same router
View 1 Replies
View Related
Sep 24, 2011
I have a Virgin Mobile MC760 3G broadband device, I want to share that 3G internet connection with my D-Link DIR-615 router so that I can connect to the 3G over WiFi on my other devices.The host computer that the 3G device would be plugged into is running Windows XP version 2002 Service Pack 2.I realize that they do sell 3G routers but I would like to use the D-Link DIR-615 that I already have to avoid buying another router. I also realize that it may be easier to share the connection by creating a wireless network on the host computer and then enable internet sharing, I don't want to do this I need to share the connection through the router.
View 1 Replies
View Related
Feb 21, 2011
I want to know if its possible to create a Vpn connection ON a router so my router automatically connects through the vpn settings.As a result all the appliances that connect to the router would be connected to the vpn without having to change any settings. Is this possible ?
View 2 Replies
View Related
Mar 24, 2011
I changed my ISP (I don't know if that has anything to do with it).I have my network setup so I have a seperate modem (tp-link td-8616), which is connected to my router (asus wl-520gu) and do most of my computing from my computer (running Windows 7 64 Bit Home Premium, wired network). I had installed tomato firmware onto my router, which was working fine with my first ISP. I changed companies about a week ago, and noticed my connection kept being dropped. At first, I thought it was an issue with my ISP, so I called them up, and didn't find a solution.
Afterwards, I started doing some trouble shooting on my own, and noticed my modem was still connected (via the WAN LED, at least), even though my router disagreed. So, I tried connecting directly to my modem and my connection would be fine without any issue at all, so I thought I'd trouble shoot the router. I switched back to the factory asus firmware, connected it back to my modem, and after a while, it disconnected my LAN connection again. My router comes with this somewhat annoying interface that tells me the issue is "You have set the wrong dynamic or static IP address for your wl-520gu." So, I investigate that, and here is the setup:
My modem is statically 192.168.1.1 when I directly connect to it, so I left that setting alone.My router is also 192.168.1.1, but this was how tomato worked, so I'm not sure that this is the conflict, so I tried setting it to 192.168.1.2, which does not seem to fix the problem.My DHCP settings are set so connecting computers are 192.168.1.100-254, which should avoid the conflicts.
View 3 Replies
View Related
Feb 27, 2011
I have a problem with my router not connecting to a modem I know is working when connecting a computer directly to the modem it works fine, but when connecting via the router there is absolutely no internet access, and multiple unplugging and resetting the router to factory defaults and resetting it up hasn't worked.
View 4 Replies
View Related
