Cisco WAN :: 887 / ATM Router As Backup
May 31, 2012
at the moment I have a 888 router that works fine, I want to configure backup (I already have configure ISDN backup but the performance it's to poor), and I want to use an other router 887 (that I already have) with adsl.
My idea is to configure the second router as stand alone gateway, and confiure in the first router a "ip route 0.0.0.0 0.0.0.0 VLAN1 192.168.0.253 100".But I know that this second route is used only in case the interface status of primary route goes down but not in case fault only protocol.
configure a better routing or faulting procedure?
-----------------------------------
888
VLAN1 192.168.0.254
ATM0.1 1.1.1.1
ip route 0.0.0.0 0.0.0.0 ATM0.1
ip route 0.0.0.0 0.0.0.0 VLAN1 192.168.0.253 100
-----------------------------------
887
VLAN1 192.168.0.253
ATM0.1 2.2.2.2
ip route 0.0.0.0 0.0.0.0 ATM0.1
-----------------------------------
View 3 Replies
ADVERTISEMENT
Jun 7, 2011
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies
View Related
Mar 8, 2012
I was just thinking about this the other day, iirc I read somewhere about hooking up a dial up modem to the aux port on a router so that if your service failed you could dial the router directly to get access and diagnose faults.
Does anyone still do this? or do you use other methods? Cause it seems a bit old hat to me and I figured if you are paying a line rental on a phone line why not get dsl as well?
View 10 Replies
View Related
Jun 23, 2011
I have one problem regarding a configuration (or setting up) of 3G SIM card for 887G router backup. That SIM card had a PIN code, so I disabled it, and now I can see that 3G light flashes Blue, so it detects 3G network. Also I can see that modem tries to dial up to connect to network, but with no luck. It has CHAP APN. Also in configuration I've found that there is PPP CHAP username and password, but I don't have any of those. I've tried to configure my SIM card with Username and Password, but it doesn't save. At the moment I have: Cellular 0 is down, line protocol is down. Dialer 2 is up (spoofing), line protocol is up (spoofing).
SIM card status is OK. Network detects O2 - IRL - yes.
It detects the network, but cannot connect to it. I'm not sure how to setup the SIM card or how to unlock it.
View 3 Replies
View Related
Sep 2, 2010
I have a problem in configuring two pair of backup interface on my customer's router (3845). It's ok when I configure just one of them. If I configure both pairs of interfaces into backup interface, one of them will be in disabled mode, as shown below :
WANR01#sh ip int bri
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 172.16.199.106 YES NVRAM up up
GigabitEthernet0/1 172.16.3.5 YES NVRAM up up
Serial0/0/0 unassigned YES NVRAM administratively down down
Serial0/0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 125.213.133.186 YES NVRAM standby mode down
FastEthernet0/2/0 172.112.22.6 YES NVRAM standby mode/disabled down
FastEthernet0/2/1 123.231.177.238 YES NVRAM up up
Loopback0 172.16.199.12 YES NVRAM up up
View 5 Replies
View Related
Apr 24, 2011
We are in the process of setting up an Amazon S3 network backup of the NAS server we have in our office. We are using a Synology NAS to backup to Amazon s3, and we use a Cisco PIX 501 to secure our network. The backup from the NAS to Amazon is going painfully slow, so I contacted Synology to resolve the issue. After they examined everything, they think the router is filtering outbound traffic, and this is causing the upload to slow down. I was told the upload should happen over HTTP and HTTPS, and I made sure these ports where open through the Access Rules. There are no rules defined in the Filter Settings.
I looked at the settings with the PDM, and I can't find where the filtering would be. I'm not too familiar with the PIX or all the network settings involved.
View 1 Replies
View Related
Jan 30, 2013
I have two routers on my local network:
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled)
2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2
There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the same subnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it possible by configuring the DHCP server to assign the primary DNS address as 192.168.1.1 and secondary DNS address as 192.168.1.2?
View 11 Replies
View Related
Jan 30, 2013
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies
View Related
Aug 9, 2012
I have a E1550 with a corrupt config that is acting very wonky lately (shows wrong info in some of the settings and doesn't always save changes). Since it may be the config that is at issue, I don't want to do a backup/resote, rather I plan to do a full factory reset and manully type everything back in.What would be nice is, creating a text based, human readable printout of the config for reference so that I don't have to manually type it all twice (once to save it, once for reentry). PS3 ports, MAC filters, etc. have several entries, and they way the pages are designed it doesn't allow for easy, whole entry, cut and paste.
View 5 Replies
View Related
Jan 10, 2012
I have a 1.5 TB USB hard drive attached to me E4200. Configuring it so that multiple computers have access and can read and write their files is quite simple. I've followed the instructions and had no difficulty.
My problem is this, after about a week's time has passed any file that has been on the hard drive for more than a week become undeletable. Any attempt to modify it or remove it pops up a message saying I need permission from a specific user (always the user that I am currently logged in as!) to perform the operation on the file.
When this starts to happen, the device is, otherwise, perfectly functional. I will still be able to create new files and delete any newly created files from the drive without difficulty even when those files are in the same directory as the files that the device will no longer let me edit. Examination of the file properties dialog shows that the files that the device refuses to allow me to delete are identical in every way to any new file that I create. Yet newly created files are removable but these older files ... are not.
I'm quickly coming to the conclusion that the HDD mounting feature of the device just doesn't actually work as advertised.
FWIW: all my computers are using Windows 7 with the latest build. I do access the device from these computers wirelessly.
View 9 Replies
View Related
Apr 6, 2009
I have finally been able to reconfigure my BEFSR41 V3 Wired Router to properly support my small server environment. I would like to know if there is a way to make a complete Backup of the current configuration that should be restored to the router if it should become "reset" to factory defaults. This happened to me approximately a week ago, and it took several days, a couple of phone support calls, and quite a bit of"grief" and aggravation/frustration before I managed to get everything re-configured correctly. If it had been "Backed up" to a file, I could have restored it and been back up and serving websites in a few hours. Instead it took almost a complete week! Is it even possible to actually backup the router? Or... must I just print each screen to be sure I get it all?
View 4 Replies
View Related
Jul 6, 2011
why Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
View 1 Replies
View Related
Mar 7, 2012
I have a WRT54GL v1.1 that has firmware version 4.30.14 build 5 installed(according to the device). The latest version listed on your website is 4.30.13. What does this mean? How do I get a backup of my current version?The device seems to be working fine and the manual I downloaded seems to cover it. I'm on a Mac so I have to set it up manually.
View 1 Replies
View Related
Aug 2, 2009
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies
View Related
Dec 21, 2011
Since lion is there for a while, it is still not possible to make a time machine backup on an USB hdd that's connected to the router. is Cisco coming with an firmware update?
View 9 Replies
View Related
Sep 17, 2012
When i connect my Seagate Backup Plus Drive to the USB port on my EA3500 the drive becomes available on my network but it never spins down even when not in use. Is there any way to correct this? If the drive spins 24/7 its going to die very fast.
View 2 Replies
View Related
Mar 13, 2007
I use a BEFVP41 VPN router. I have changed several settings. How can I backup these settings and store these settings in a save place.
View 3 Replies
View Related
Oct 7, 2012
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
View 4 Replies
View Related
Oct 18, 2011
After the upgrade of LMS 3.2 to LMS 4.01 everthing works. After i fixed my last problem (syslog time issue). I´d saw that the automated system backup doesn´t work. I´d tried to backup the system by script. Than i find out that the perl.exe is damaged (0KB). So than i copied the perl.exe from my old Cisco Works Server to the new Server. Than i tried to make a Backup and get the mentiond error ...
D:CiscoWorksCSCOpxin>perl.exe D:CiscoWorksCSCOpxinackup.pl d:Temp
ew
install
************************************************************
Backup to 'd:/Temp/newinstall' started at: [Wed Oct 19 09:39:50 2011]
[Wed Oct 19 09:39:50 2011] ERROR(375): No database files are available for the
installed applications; nothing to back up.
[Wed Oct 19 09:39:50 2011] Backup failed: 2011/10/19 09:40:00
[code]....
View 1 Replies
View Related
Jan 10, 2013
Why does Cisco recommend a configuration of originate-only on the ASA with multiple peers configured and the answer-only to the other end? Shouldn't it work as Bi-Directional ?
[URL]
The only scenario I see which could break is if both peers try to establish a VPN at the same time to the ASA. Is there any other reason ?
View 0 Replies
View Related
Nov 21, 2012
1)how can i backup the configuration on cisco lms 4.2 and to re-imported later when i re-install the lms 4.2
2)how can i change the admin password on cisco lms 4.2
View 3 Replies
View Related
May 5, 2011
One of my branch offices is connected to an ADSL line as well as a VDSL line.Since I really don't need the ADSL line I came up with the idea to use it as a backup line.So I searched google and found this nice little article URL. I wonder if the router will switch back to the primary ISP if the primary line comes up again?
View 3 Replies
View Related
Nov 21, 2012
Any one see the pronl;em where LMS 4.2.2 cannot backup an ASA 5525-X (UKHSL-N01-AFW02)..The Inventory collection is fine, to a point.I have applied all updates LSM etc. [code]
View 7 Replies
View Related
May 3, 2006
I am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR. If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1? I would like to use percents (%) for the values, i.e. voice can use 25% of the link, then it would make more sense when using the backup T1 link.
View 2 Replies
View Related
Nov 21, 2012
if i enable Controller Configuration Backup is that included in the server backup? and can the controller configs be specifically extracted from the server backup?
View 8 Replies
View Related
Apr 11, 2012
We have cisco works LMS 3.1 and the server have very problems, we need format the server and reinstall the Cisco Works, when I doin backup and restore of data LMS We lost the licenses? or when we restore the data in the server we have the same licenses? or get the new licenses to cisco?
View 5 Replies
View Related
Feb 11, 2013
implement backup WAN links to complement the metro Ethernet links we currently use so we have some redundancy. These will most likely be a VPN over an Internet service but might be another Ethernet type service, the medium shouldn't really matter I wouldn't think. What I am looking for input on is what is the best way to implement this? Would I just set costs so that the backup is only used when the primary goes down, or should I create new OSPF area for the backup links?
Currently the core switches that are also our routers are 3750G stacks running ip services. We are getting ready to install new firewalls at each location that will become the gateways for the vlans currently on the core switches to give us much more control over segmentation, and because of this I am thinking that it may make sense to then move the OSPF instance from the core to the firewalls. In the drawing I did not show the access layer switches off of the core, and the MOE circuits actually terminate into a 3550-12T switch before the core. I think I will actually eliminate those 3550-12T switches and go straight into the core. This is a current state drawing, so does not include the backup links I am planning.
View 4 Replies
View Related
Feb 18, 2011
want to connect three networks with each other via two media one ethernet/fiber optic and other through wireless as backup link.how can i connect these three networks so that if my ethernet/ fiber optic connection fails than computer on networks can still communcate via wireless link (i mean if ethernet/fiber optic fails then wireless link should automatically be established/
View 1 Replies
View Related
Jan 18, 2013
Platform: LMS 3.2.1 with RME 4.3.2 on Windows 2003.I'm having a problem with several devices that were backing up fine until this week - suddenly they aren't backing up their running configurations, but RME is fetching their startup configurations fine and VTP backups are fine. At first I thought it might be timeouts, so I used inline edit to incease the telnet timeout for a device to 180s. However, the job fails well within this time period (debug shows on i/o error?). My order of protocols is SSH, Telnet, TFTP. I took a stab in the dark that this suggested a database problem so I picked one at random and deleted it from DCR, and readded it and it worked. However, for the other 48 devices affected it did not.
I'm wondering if I need to do anything to the RME database to get things back to where they were? Do I need to reinitialize the RME database, and if I do that what do I lose? [code]
View 2 Replies
View Related
Nov 27, 2011
I tried to backup ACS 5.1 but i found error messages as below
acs backup25Nov11 repository 25Nov11Repository
% Repository not found
% Error: Invalid repository name 25Nov11Respository
Please use a configured repository.
View 2 Replies
View Related
Jun 8, 2012
How to backup the configuration on cisco acs 5.2 and how to restore it , if some thing wrong happened
View 7 Replies
View Related
Dec 9, 2012
I have an ASA 5510 running 8.4 with dual ISPs setup on 2 different interfaces: outside(primary),backup(backup). I also have a site to site VPN to another ASA in another city. The VPN is now setup on the outside interface and works fine. What I wanted to do is to make the VPN run over the backup interface only.
So, I modified the the crypto map on the remote side to use the backup interface IP and created a tunnel-group for it. I then created a crypto map for the backup interface and enabled ikev1 on it. The default route is set to use the outside interface so I created a static route that routes traffic bound for the outside interface on the remote side to the backup interface default gateway. I can get the tunnels to establish but no traffic is passing through them. I though then that I need a NAT for the tunnel traffic to I created a NAT as well but still no traffic passed. I tried the packet-tracer and it said the traffic was allowed and from the show crypto ipsec sa command I can see the tunnel setup but no traffic will go across it.
View 5 Replies
View Related
Mar 10, 2013
Cisco ACS 5.x appliance?How to back up Config?What is best way, via TFTP? COPY Startup-config tftp:?COPY Running-config tftp:?I currently use Solarwinds CatTolls to back my Cisco Switches, can I use this for Cisco ACS also?
View 3 Replies
View Related
