Cisco WAN :: ASR1002 / Unable To Use BGP Route-map Match Next-hop On Inbound?
Feb 28, 2011
I am running ASR1002 with latest XE IOS version asr1000rp1-adventerprisek9.03.02.01.S.151-1.S1.bin configuration bellow
router bgp 65000 bgp router-id 1.1.1.1 bgp log-neighbor-changes timers bgp 5 15 ! address-family ipv4 vrf LABR01-VRF bgp router-id 1.1.1.1 neighbor bgprrclient peer-group neighbor bgprrclient remote-as 65001 neighbor bgprrclient password 7 1234 neighbor bgprrclient update-source Loopback0 neighbor bgprrclient version 4 neighbor bgprrclient route-reflector-client neighbor bgprrclient route-map set_weight in I then tried to create new route-map and get error that match next-hop can not be used on inbound
route-map set_weight permit 10 match ip next-hop prefix-list thirdparty match as-path 1 set weight 1000
LAB-ASR1002(config)#route-map set_weight permit 10LAB-ASR1002(config-route-map)# match ip next-hop prefix-list thirdparty% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match% "set_weight" used as BGP inbound route-map, nexthop match not supported% not supported match will behave as route-map with no match Not sure why Cisco is not supporting a pretty basic feature for BGP route maps.I tried looking into matching other variables but I am unable to get same result as I have same routes on bgp table from multible inbound peers.
I also get this message when configuring tacacs. I looked for "new" cli but no luck:LAB-ASR1002(config)#tacacs-server host 2.2.2.2 This cli will be deprecated soon. Use new server cli
View 1 Replies
ADVERTISEMENT
Sep 16, 2012
I cannot receive any OSPF route from Nexus to ASR1002 even they are both OSPF neighbour. I have attached the config for both, Both Nexus and ASR part of Area0.
Config
ASR1002#sh ip ospf neighbor
Neighbor ID Pri State Dead Time Address Interface10.165.117.12 1 FULL/BDR 00:00:35 10.231.175.226 GigabitEthernet0/0/0
[Code].....
View 2 Replies
View Related
Aug 20, 2012
I have a C3825, and have been using standard ACLs and a PBR to route certain HTTP traffic via an alternative default gateway:
route-map RTRMAP-OfficeLAN permit 10
match ip address RTRMAP-OfficeLAN-toADSL
set ip next-hop x.x.x.x
This is working absolutely fine, and as expected, all traffic matching the ACL is being sent to x.x.x.x However, we have recently expanded our network, and I am now receiving various networks via BGP from various sources. All BGP incoming via iBGP is tagged in communities:
Community (expanded) access list 100
permit 37xxx:100
Community (expanded) access list 200
permit 37xxx:200
Community (expanded) access list 300
permit 37xxx:300
[code].....
All communities are also matching prefixes when executing either 'sh ip bgp community 37xxx:100' or 'sh ip bgp community-list 100' What I am trying to achieve, is create an EXCEPTION for the policy route. Traffic matching the community lists, must be forwarded based on the routers routing table, whilst traffic maching the ACL, must be sent via the policy route...
route-map RTRMAP-OfficeLAN permit 5
match community 100 200 300 400 500
!
route-map RTRMAP-OfficeLAN permit 10
match ip address RTRMAP-OfficeLAN-toADSL
set ip next-hop x.x.x.x
My logic dictates to me that the above should work, but looking at the route-map, I get matches on seq 5 and pacets are exiting the route-map as expected (first matched). However no traffic that does NOT match community 100,200,300,400 or 500 and that DOES match the RTRMAP-OfficeLAN-toADSL never matches.
The counters on the route-map for seq 5 is increasing, but no counters are increasing at seq 10.. It's almost as if seq 5 is matching all traffic.
View 1 Replies
View Related
Nov 22, 2012
I have upgraded an ASA 5505 to 9.0(1) as I would like to use ipv6 version of dhcprelay. That said, I am unable to obtain a global unicast address but the link-local address is able to communication with the ISP's gateway/DHCP provider which I hope will allow v6 dhcprelay provide internal clients with IP's from the ISP. Trouble is, unsolicated inbound ICMPv6 messages from the ISP's gateway are being dropped on the way into outside interface.
%ASA-3-313008: Denied IPv6-ICMP type=129, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
%ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::201:5cff:fe3b:3c41 on interface outside
[Code]...
View 4 Replies
View Related
Feb 12, 2012
I'm trying to get IPSec VPN working onto a new Cisco ASA5505. Pretty standard configuration.Setup:
* Cisco VPN client on Windows 7 (v5.0.07.0290 x64 on Laptop1 and v5.0.07.0440 x64 on Laptop2)
* PPPoE/NAT and internal DHCP on the ASA were configured with the Startup Wizard in ASDM
NATting is working fine - internal PCs get an IP address in the 192.168.2.0/24 range and can all access the Internet.I wanted to be able to connect from anywhere to the ASA in order to reach one of the internal servers. Should be pretty basic.First I tried with the built-in ASDM IPSec Wizard, instructions found here.VPN clients can connect to the ASA, are connected (until they're manually disconnected), but cannot reach the internal network nor the Internet. Note VPN client can connect fine to a different VPN site (not administered by myself). [code]
Unfortunately I'm getting the same "AddRoute failed to add a route with metric of 0: code 160" error message.I'm very confused as this should be a pretty standard setup. I tried to follow the instructions on the Cisco site to the letter...The only "differences" in my setup are an internal network of 192.168.2.0 (with ASA IP address 192.168.2.254) and PPPoE with DHCP instead of no PPPoE at all.
View 5 Replies
View Related
Mar 17, 2011
We have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies
View Related
Jun 16, 2011
I've got an existing Cisco 1841 connecting to a 10Mbps Internet Leased line. With my current setup I've configured PAT for internet access for my users, and we also have some servers on site which are assigned public ip addresses, these can be accessed from the internet. Now we have procured a Cisco 1921 ISR to replace the old 1841, when I connect the 1921 with an identical configuration in place of the old router, 2 things happen.
1) The users accessing the net via the nat are able to work without any inconvenience (good)
2) My servers which have public IP addresses are unable to reach the internet and subsequently I am unable to reach them via the internet (very bad)
View 10 Replies
View Related
Apr 22, 2012
i have a Layer3 Switch Cisco WS-c3750G -24T , initially i have a IOS version c3750-Ipbase , recentely i have upgraded my IOS to c3750-Ipservices-M to enable to PBR for my network , i have created all the acl and tried to give the route-map with PBR , the command was initiallying but i am not able to see the applied route-map in my policy route , i have gone through the blog and enabled SDM prefer routing , but no luck .
View 1 Replies
View Related
Jul 24, 2012
The host IP 84.204.x.x unable to announce through BGP
BGP configuration on Cisco 1841:
!
interface FastEthernet0.1201
encapsulation dot1Q 1201
ip address 172.18.11.1 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
code]....
View 4 Replies
View Related
Jul 14, 2008
Cisco 4404 WLC
AP 1240 - LWAP
Wireless client receives a DHCP address from central DHCP server fine. Unable to route outside of own subnet . Continuous ARP WHO HAS (Default Gateway addr) TELL (client IP) messages being received. WLC running OS 4.2.99.0.
View 20 Replies
View Related
Jan 12, 2013
I have an issue where I can get traffic to pass from HDQ to two branch offices over our ipsec/gre tunnels even though the tunnels appear to be UP. The HDQ is a 2811, branch is a home office using an 871W and branch runs a 2801 router. I initially had HDQ working fine with the 871W but when I configured branch2 (2801), they both broke. The tunnels appear to be up but traffic is not routing across them. The two 2801 routers run 12.4 (c2800nm-adventerprisek9-mz.124-24.T2.bin). These are gre over ipsec tunnels. Currently traffic flows over an exsting MPLS network that we are getting away from due to cost. As soon as I change the routes to point to the Tunnels, it breaks. Traffic doesn't appear to pass through the tunnel. I have attached my sanitized configs.
HDQ#sh crypto sessCrypto session current status
Interface: FastEthernet0/1Session status: UP-ACTIVEPeer: 205.205.205.21 port 500 IKE SA: local 204.204.204.66/500 remote 205.205.205.21/500 Active IPSEC FLOW: permit 47 0.0.0.0/0.0.0.0 0.0.0.0/0.0.0.0 Active SAs: 4, origin: crypto map IPSEC FLOW:
[Code]....
View 3 Replies
View Related
May 1, 2011
Have cisco router 1921 and 3 cisco switch 3560G i want to configure the cisco router so as network 192.168.4.0/26,192.168.3.0/26,192.168.2.0/26, all to access internet R1921(config)# ip nat inside source list 102 int G0/0 overloadR1921(config)# access-list 102 permit ip ?
I am right to do this below?
R1921(config)# ip route 192.168.4.0/26 10.10.10.2R1921(config)# ip route 192.168.3.0/26 10.10.10.2R1921(config)# ip route 192.168.2.0/26 10.10.10.2
assist on access-list and ip route?
View 20 Replies
View Related
May 12, 2011
i have configured SSL VPN on Cisco ASA5510 which is working fine .My Users connected the VPN and access the servers remotely. But now i face one challange my users use PPTP VPN of the customer now a days configured at the Customer Network. When they Connect the PPTP VPN unable to Access the servers remotely defined on the SSL VPN Route.
View 1 Replies
View Related
Oct 9, 2012
I have a Cisco 527w which we are wanting to deploy to our remote sites however i've found a bug. We use ADSL with an IPsec tunnel as primary and 3G APN for failover . When the ADSL goes down the route via the IPSec tunnel remains and i am unable to route the traffic via the APN backup without disabling the VPN tunnel .
View 0 Replies
View Related
Nov 23, 2012
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies
View Related
Apr 22, 2012
Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
sh boot
coreswitch#sh boot
BOOT path-list : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin
[Code].....
View 9 Replies
View Related
Jan 7, 2013
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
View 4 Replies
View Related
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Aug 25, 2012
I am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies
View Related
May 29, 2013
Right now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
View 2 Replies
View Related
Jan 27, 2011
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
View 2 Replies
View Related
Feb 21, 2011
We have pair of Cisco Nexus 7018 with four eight port 10gig modules.I have created two VDC's with mixing 10gig ports from diffrent modules.Now we requied some one gig SFP ports and we are planning to buy 48 port 1gig sfp+ card.My question is can
1- Can I still mix and match 1gig and 10 gig ports in two different VDC's? (1-24 for VDC1 and 25-48 for VDC2)
2- All 48 port module hve to allocate to one VDC which alreday have all 10gig ports.
View 3 Replies
View Related
Feb 5, 2009
Is the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies
View Related
Mar 11, 2012
We have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies
View Related
Aug 17, 2011
I'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
View 2 Replies
View Related
Jun 25, 2012
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies
View Related
Oct 14, 2012
We have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies
View Related
Oct 18, 2011
We are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies
View Related
Apr 6, 2013
im trying to create a VPN between a Cisco ASA5510 and an ASR1002 when my Loopback interface is The Source IP . [code]
View 1 Replies
View Related
Oct 23, 2011
what command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
View 6 Replies
View Related
Dec 27, 2011
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
View 2 Replies
View Related
Jun 19, 2011
I've inherited a project building an internet connectivity solution for a large corporate. It has its own AS and its own PI space. They are putting in 100Mbit connections from 5 different Tier1's , taking full internet routing from each. Cisco ASR1002's have already been specified and purchased for the job. I'm not familiar with the ASR platform at all - is it up to the job with full routing tables? multiple instances of full tables ? (not likely to put all 5 into one box!)
View 2 Replies
View Related
Apr 1, 2011
If I want to use the command match protocol xxxx when configuring traffic classification for QoS, is necessary to have the following licence?
-FLASR1-FPI-RTU
-Flexible Packet Inspection RTU Feature License for Cisco ASR 1000 Series.
View 1 Replies
View Related
