I have two routers that have problems with the fans. It is a c3725 and c3845 (Fan 3). I would like to know/confirm what are the products of these fans:
c3845: CISCO3845FANASSY= Cisco 3845 Fan Assembly and Bezel
c3725: CK-3725-FAN (external product)
In c3845 can be exchanged only the Fan 3?
In c3725 the CK-3725-FAN work?
I have c3725 router that have two WAN interfaces, both of which I want to serve VPN clients. However, I have only one default route, say for WAN1, so how can I accept client requests on WAN2.
ps: I use vpdn and pptp, and I'm a newbie to Cisco router and IOS.
We have a 3845 router, IPBaseM, ver 12.4(15) that seems to accept an SFP (GLC-LH-SM). It does not show up on a show run, or Sh Ip int brief. If I type show tech-support | include sfp, it returns "sfp_transciever_cod 0x2 (1000BaseLX)".How do I go about configuring it for Ethernet Private Line access?
View 1 Replies View RelatedWe have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
Can I use Sharepoint print services with a macbook pro and a Vista 64 desktop?
View 3 Replies View Relatedi need replace a Fortigate 310B with Cisco products, that is, all Web Filtering, IPS/IDS, AV, so, the question is, what we can use to replace?First, we can use Cisco ASA 5520 right? with CSC Module, so, this for Anti-X, but for IPS? is better router with IPS on IOS? or IPS Sensor? or other Cisco ASA with IPS Module?
View 3 Replies View RelatedCustomer has a pair of Cisco 3745 configured with DLSW+...He is in a technological migration phase so he needs to migrate to new cisco platforms.How can I find out which cisco products (switches, routers) support DLSW+ to replace the 3745s?
View 4 Replies View RelatedI'm having some serious sound problem with some 2950 Cisco switches that I have in my CCNA lab these switches sound like a jet I've gone in and made sure the fans are clean and I even replaced one they still are too loud. So I have a few options I can run them without a fan which I really don't want to do but I want to look at two other options. The first option would be to put a heat sink on the chip that's producing heat I also thought about cutting a whole in the top and mounting a 120mm fan.
View 4 Replies View RelatedBasically I run 3 voice gateways on 2821 routers. In two of my routers I've had fan failures, one router has had two fans die and one has had just the one.
I was going to buy the offical Cisco fan replacement kit but then I thought with such as high failure rate I'd rather buy something else and better guarentee the service to my call centres.
So, what i'm asking is:
- Is there any reason why I cannot procure a standard 80mm 12V fan with a better rating (cooling and reliability) and install this in my 2821's?
I understand this may invalidate any warranties but mine have long expired.
I have a 3725 router that is reporting the following syslog message:
%FAN-3-FAN_FAILED: Fans had a rotation error reported.
When I do a show environment all, I am getting the following message:
Fan status: Warning- low fan rpm condition detected.
Both the the fans are functional and are rotating fine. How do I repair?
I've just plugged in 4 Nexus5548 switches and ran through the initial setup without any issues. However, the fans seem to be stuck on full speed. At the moment they're the loudest thing in the server room.
I know this isn't the most recent OS however I was hoping to avoid updating if necessary as I don’t have the service agreement linked to my account and can’t download the update without it. Is there anything else I can try first or anything I have missed?
Software BIOS: version 3.5.0 loader: version N/A kickstart: version 5.1(3)N1(1a) system: version 5.1(3)N1(1a) power-seq: Module 1: version v1.0 Module 3: version v2.0 uC: version v1.2.0.1 SFP uC: Module 1: v1.0.0.0 BIOS compile time:
[Code]......
I have a 3750-48P when plugged in has fans that spin up, but no lights on the front of the chassis. Does this mean the power supply is bad? If its bad, why do the fans power up? Also, i am not receiving any data through the console.
View 6 Replies View Related1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies View RelatedWe are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies View RelatedI want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedI have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies View RelatedI have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies View RelatedI am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies View RelatedI currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies View RelatedI am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies View RelatedI bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies View RelatedI am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies View RelatedI would like to know the IOS which supports :ACL Support for Filtering on TTL Value feature on my Cisco 7600 device. I check on cisco and found the Cisco 12.4T release but this software doesn't fit onto my chasis. which software should I upgrade to on my cisco 7600 to have this feature.
View 5 Replies View RelatedI have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies View RelatedI finally got the Site to Site Vpn from our corporate to remote site. Is there a way to connect a cisco phone over that network. Since both Voice Vlans are exempt from acl I would imagine all traffic is clear to go accross? and if so I just have to set the phone to our tftp/ccme. Will that work.
View 2 Replies View RelatedI want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies View RelatedI have the CISCO 1800 and I have there the HWIC-2T. I have two questions.First is an easy one. I want to replace the HWIC-2T with HWIC-4T but the CISCO 1800 guide and the HWIC-4T guide says that they dont fit together but I inserted the HWIC-4T in to the CISCO 1800 it recognized him with all the 4 Smart Serial ports that it hase. The question is, how can I check if the CISCO 1800 supports the HWIC-4T?Second question is how can I configure one of the Smart Serials in the HWIC-2T/4T to comunicate with the X.25 Protocol? What I have now is at one end CISCO 1800 and at the other end CISCO 2800 and they are comunicating with each other throught one of the Smart Serials they have. I want to connect to each one of then an old pc that comunicate only with X.25 and I want this two computers to comunicate with each other throught those two routers.
View 2 Replies View RelatedWe're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
I'm trying to understand CEF; I know it's used most commonly in layer 3 switches but that routers can also do it. The routers that support CEF must have special hardware I'm assuming? (Since CEF is layer 3 processes in ASICs) How can we check if a router is capable of CEF? Does anyone know a good link/graphic that shows how much faster CEF is than software-based layer 3 processes?
View 10 Replies View Related