I have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my the modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again.
View 1 RepliesI have setup a Cisco SR520W and everything appears to be working. After a few hours, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device.
If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my the modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again.
Here is my config file:
Building configuration...
Current configuration : 17830 bytes!version 12.4no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msecservice
[Code].....
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedMy internet (wired and wireless) usually works fine, but occasionally (read: every few days to weeks) the connection will suddenly black out for a period of time, anywhere from an hour to a day. I have tried resetting both my router and modem, and going through all the settings on my laptop, but I'm pretty sure it's not my computer, as no other devices can connect either. During the blackouts, when I look at the modem, the internet light will turn on for a second, then go off and then the red "alarm" light (aka "something is wrong" light) starts blinking like crazy, and this keeps repeating. This resolves itself after anywhere from a few hours to a whole day and everything is normal again. The light show, and the fact that I can't find any other problems, leads me to believe that it could be a problem with my provider (or the network itself) and not a hardware or software problem, but I can't be sure of this.Also, during the blackouts, I can connect to the network, but it shows that limited connectivity symbol (exclamation mark thing) and says no internet.
View 5 Replies View RelatedI have a Cisco 2911 router with 4 T1 connections. Two are set as a multilink and the other two are for two other locations. The router will run fine, but after a month I cannot ping the gigabit ethernet 0/0 interface. I would have to manually reboot the router to get it to respond again. Before I noticed a lot of interface discards which would shutdown the 2911 and a manual reboot would be needed, but for this time it isn't the case. Where would I start with this the memory and cpu usage are fine.
Here is the config:
Current configuration : 2905 bytes
!
version 15.0
[Code].....
I have a Philco PHN 15006. My drivers should be up to date. Since I've started using it, I noticed I lose connection with internet and then I have to restart the switch/router. Then, it starts working again. I used to have to just open the Solve Problems and then it would connect again. But now, I tried just unplugging the Ethernet Cable and plugging it again. It had the same effect as restarting the switch. So, the problem must be in the notebook.The wireless internet is worse, because it connects for a while then stops connecting, while my other computer connects with no problems.
View 12 Replies View RelatedI have two 3560G 24p switches, connected to each other via two links in Etherchannel. From one of the switches i retrieve SNMP info about port status and traffic for these two ports. That works great, until i pull out random cable. The switch responds with ifOperStatus = 2 and traffic drops to zero for that partikular port, as it should. But a some of seconds later it stops responding to my snmp reguests for ~ 5 seconds. That causes problems as my watchdog sets an alarm as it thinks the connection to the switch has been lost. (It checks switch uptime is increasing all the time)
If I set a delay on the watchdog on my monitoring system of 15sec, it works. But it ain't that nice to have a delay of 15 sec if the connection really is lost.
I am only getting half of what my internet speed should be when I am connected to the router.
when i connect to the modem directly from my pc, I have 50-60 down..
i recently deployed cat4507e switch along with 3 nos of WS-X4748-RJ45V+E - 48 port gigabit PoE modules. I am using polycom IP560 phones.
I am facing issue of some switch ports (randomly) stops supplying power to phone at random time. So far there are about 4 incident and i have been plugging those connection to different - usused ports. I am planning to RESET the switch module during weekend and i think it might fix issues with those ports.
But what would be quick and easy way to fix this issue when the issue is faced? How/what to check on switch port interface wrt to power? If switch module is falling short of overall power requirement, is there a way to boost the power?
i have a 876 Router, connected to the Internet and a VPN. From inside i would like to pass all traffic destinied to 192.168.0.0 255.255.255.0 to the VirtualPPP IF and al the other to the Internet (vlan2) I have created this rule, but after applying ist works only for about 30 to 60 seconds. after that only the Internet reachable. Everytime i do a clear ip nat trans * both Interfaces will work für 30 to 60 secs again...
This is the relevant part of the cfg
ip nat inside source route-map Di1 interface Virtual-PPP1 overload
ip nat inside source route-map VLAN1 interface Vlan2 overload
!
access-list 1 remark CCP_ACL Category=2
[Code].....
I have a cisco asa 5010 where, during the process of configuring, the outside ports become down/down. The /0 port won't even reactivate after cycling power on the unit.Port /1 is the inside interface and it is not affected by the problems.I switched the outside port to port /3 and it worked for awhile then it stopped working. I switched it to Port /2 and the same thing.Port /2 and Port /3 are on after a power recycle but shut down completely (down/down) during the reconfiguration. It seems like a hardware failure, but I'm wondering if it could be anything else.
View 4 Replies View RelatedI recently setup a site to site vpn between a asa 5510 and router 1921. It was working great all night and this morning. When traffic stopped rolling through for a few hours the tunnel shutdown. I checked the router using cisco configuration and tells me the tunnel is up. When I check the asa it does not show up in the active tunnels. Any know what would cuase it to drop? and if so what can I do to avoid it.
View 6 Replies View Relatedi've an Cisco ASA 5510 with Security Appliance Software Version 8.0(2), in this ASA i've many L2L tunnels to this ASA, anda sometims new tunnels can't connect, the older tunnels still ok and working, yesterday this situation occured again and i've tried to clear all ipsec tunnels and try to reconnect again no one cames up again. At the time of this situation memory usage was about 78% and CPU is was around 5%. I've made a reload without changes and the situation returns to the normality.
At the time of the fail i've collect the outpu from debug crypto isakmp 255, the outpu was in the annexed file.
I find are steps to turn on SSH access. I have quite a few customers with ASA5510's installed. SSH is set up and working fine on every one. After a period of time, you are no longer able to SSH into the firewall. Using Putty, it just sits there on a blank screen without giving a "denied access" message or a login prompt. Rebooting the firewall will solve the issue and SSH access works again. Today, I had a customer with and active/standby configuration where I had to reboot both of them to be able to log in. Most of my customers are on 8.2.software as most don't want to reconfigure for the new NAT, etc.
I'm sure others have seen this before since it appears to be occuring on almost every ASA that I have access to. Is there any fix to eliminate this or is there something that can be run from the ASDM that will grant SSH access again without just doing a reboot?
I have a problem with configuring brach router 891 (with IOS v15.0(1)M).I want to connect to HQ via EasyVPN connection (split-tunnel) and allow the local traffic to go directly to the Internet via NAT (PAT).When the VPN connection goes up, NAT stops working and NAT translations don't appear in show ip nat translations. When the VPN connection goes down, NAT begins to work again.
View 1 Replies View RelatedWe have two WAP2000's in our offices which we roam between depending on which office we are in. Lets call them Access point A and Access point B.Both are firmware 2.0.4.0 and have seperate IP addresses. Both are set up with two SSID's and VLAN tagging. Both handle connections just fine and can route traffic. Both are PoE and the catalyst switch reports PoE util at 25% over all of its ports.After 10 minutes of uptime, Access point B will close all of its TCP ports - SNMP, Web admin etc but does still handle wireless connections and traffic correctly. Access point A does not close any ports.I have confirmed that when the problem happens, Access point B still handles traffic just fine by checking the MAC address the clients is associated with, as well as powering down Access point A and confirming traffic is flowing. Access point B will also respond to ICMP ping after it has closed all of its management ports. I have confirmed there is no other device on the network attempting to use the same IP address as Access point B.
I have also confirmed that I am attempting to access the management ports from the management Vlan (1) - else I would not be able to reach Access Point A's management ports either. I have turned wireless management access on for Access point B and the ports close after 10 minutes of uptime from the wireless side too, so highly unlikely this is a vlan issue.I have confirmed all of the settings (bar the IP address config) exactly match on both Access point A and Access point B. The firmware revisions are the same.
I have an doubt about some port in 2960.He have 2 SFP and 2 Fixed Ethernet. Can I use these 4 ports in the same time? Use 2 Ethernet and the 2 SFP with Fiber?
View 2 Replies View RelatedI have a Asus n55s. The wireless acts very funky. It sometimes disconnects and stops working. Sometimes, it will stop detecting any nearby wireless networks altogether. Then I have to enable and disable the wireless functionality until it starts seeing nearby wireless networks.
View 9 Replies View RelatedI've been having this problem with my laptop's wifi for a while now and it's been getting a little out of hand lately that I can't deal with it anymore. I asked some friends and they seem to have the same problem too but not nearly as often as I do. Every so often, my laptop's wifi just stops working so I turn it off and then turn it back on and it starts working again. My friend says it happens very rarely to him but for me just today it happened 2 times within 10 minutes
View 7 Replies View RelatedI'm having is that every few hours my TCP/IP protocol stops working. The modem lights remain normal but I can't connect to anything. The only thing that works on the internet is traceroutes at the command prompt which function normally. The solution is that I have to reboot and then everything returns to normal until a few hours later when it happens again. There are no error messages on any of my browsers. The page just goes white immediately. When I try to retrieve my email, I get a message about the TCP/IP isn't working.
View 9 Replies View RelatedI've got the same problem on my wife's Acer One 532h. Did it get resolved for you, Adrian and if so, how?
View 5 Replies View RelatedOn Windows XP, my integrated NIC stops working after hosting a server. The server starts fine, ports are forwarded, firewall is down, modem is fine, but when I receive a connection, it shows they have made a connection, but then they drop, as do I. I can't browse or ping anywhere. I have to physically disconnect, then reconnect the ethernet cable to the port, or restart the computer. Upon ipconfig, the adapter is set with the Windows default ip (169.x.x.x) and cannot be /release'd or /renew'd.
View 10 Replies View RelatedIt's fairly hard to explain what happens but basically, say I'm playing some type of online game, all of a sudden anything server sided such as HP amounts, damage amounts, etc. just disappears but the animation runs fine such as attacking being hit, etc. All of a sudden it'll jump forwards and I'll take any damage and do any damage that had been happening until the issue started. This happens constantly and it's really frustrating but on top of that my internet will slow to a crawl..Say I'm trying to send a message on Skype, it won't send for the longest time and I won't be able to recieve any or even open a new webpage until the problem fixes itself.'ve looked around a bit and thought I fixed the issue, I'm on wifi and multiple devices are connected but not always in use, and the forum I found suggested an ip conflict and said to open up command prompt release the ip with ipconfig /release and then renew it with ipconfig /renew.
View 3 Replies View RelatedOnce every couple of days the wireless service seems to disappear. I've connected to the router from a wired computer and everything looks ok from the d-link panel, however its not showing up as an available wireless network on the wireless units. Pulling the power off for 30 seconds tends to get it working again. I'm configured bg and n. I need a mix... an old B laptop, have one machine that has a G NIC, and the rest are N.
View 14 Replies View RelatedAfter buying a new WNDR370. Sporadically and seemingly without any cause my internet will stop working. Diagnostic will always report it as "DNS Server is not responding." I've also discovered that if I enter my router settings and even just switch the DNS settings from Auto to manual or vice versa the problem corrects itself instantly-then next time it happens I just need to do it again.
I've already tried resetting my entire network and rebuilding the recommended way. Modem, Router, then computers-connecting each only after the prior has finished initializing. Hasn't worked though.
Currently I have my main rig connected directly to the modem to try and find out if I experience the problem at all this way, this is a pain in the ass though, and I don't know when long enough is long enough as the issue is completely random and simply just may not happen.
I have an EuroDOCSIS 3.0 cable modem from UPC Romania. It's a Cisco EPC3925, wireless modem.
My problem is that most of the time (like 80% of the time) when someone is starting or closing a PC that is connected using a wire, the whole internet crashes (wired PCs get a ! sign and the internet stops working and wireless PCs are getting disconnected completely from the network being unable to reconnect). This is solved by restarting the modem (unplugging/replugging it) or waiting for it to reconnect. I want to mention that during this process the modem lights show that everything is ok and nothing special happens.
First of all I called UPC technical support and the man there said that I should try to disable the firewall from the modem (which I had disabled already), if it won't work then to try to reset the modem to the factory settings (as I was thinking to do - because I configured the settings as I wished) and if this won't work then calling them back to change the modem.
I tried to reset to the factory settings and that didn't work at all after running tests over one week. After that I called UPC and they said that the modem is for sure the problem, they sent a technician (today) who also said that the modem is the problem. Ok ok, the technician replaced it and everything seemed to be good.
30 minutes ago my father started his PC and what should I see? Bam, internet crashing. 5 minutes ago i closed as well my PC and what should I see? The internet crashing again.
My Cisco 871w still stops working once a week.Today I found it frozen, after the weekend, and I have executed few commands from the HyperTerminal .The commands were given by cisco coleagues in previous post :show logshow ip int briefshow interfaces counters errorsshow interface FastEthernet1show interface FastEthernet1 statshow interface FastEthernet1 summaryshow interface FastEthernet1 switching
View 4 Replies View RelatedI have a PIX 515e (8.0 (2)) and 1841 router (12.4(25)).I had the following setup working without issue:
[Internet] <-----> PIX <-----> 1841 <-----> [LAN]
I then tried to introduce VLANs and now I can not reach the Internet from the LAN. It seems that no nat translations are taking place.
-I can successfully ping the LAN from the PIX.
-I can successfully ping the Internet from the PIX.
-I can successfully ping the PIX inside_lan interface from the router
-I can not ping the outside interface from the router
-I can not ping the Internet from the router
I introduced the LAN side VLAN first and everything still worked. However, once i introduced the VLAN between the router and PIX, things have broken down. [code]
I have two Cisco ASA 5520's running software version 8.2(2) set up in a HA pair. The L2L vpn is set up and works as expected between this site and another. The issue is that every few months, one subnet of the VPN, the same one all the time, stops forwarding/receiving traffic. The device in the remote location is not a Cisco device but I am certain the issue lies with the ASA as when I fail over to the slave device the VPN works again, failing back again however stays with the subnet still not passing traffic. I need to reboot the device before it starts forwarding traffic on the subnet again.
View 3 Replies View RelatedIs there a way to configure a switch (3550, 3560,3750) to disable a switch port if it has not been used for a specified time period such as weeks or months. Say you want the switch to disable switch ports that have been "abandoned".
View 8 Replies View RelatedMy computer runs bit torrent almost all the time, sometimes when I start Firefox the home page google never loads and neither do any other web pages yet bit torrent is still working as if nothing has changed. If I start a download in Firefox come back to the pc a few hours later Google doesn't load but the Firefox download still continues.What causes this is it DNS ?
View 2 Replies View RelatedI have a problem with a wireless adaptor on a Toshiba Tecra (A11-1EE - PTSE0E-065052EN) running Windows 7.The wireless adaptor works fine but every now and again it will just stop working. The operating system says that the adaptor is turned off but it isn't. I've checked the driver but it is up to date.I have to disable the driver and then enable it again and then the adaptor begins to work correctly again.
View 4 Replies View RelatedTech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft� Windows Vista� Home Premium, Service Pack 2, 32 bit
Processor: AMD Athlon(tm) Processor LE-1660, x64 Family 15 Model 127 Stepping 2
Processor Count: 1
RAM: 2045 Mb
Graphics Card: NVIDIA GeForce G210, 512 Mb
Hard Drives: C: Total - 292284 MB, Free - 43340 MB; D: Total - 12958 MB, Free - 1819 MB;
Motherboard: PEGATRON CORPORATION, NARRA5
Antivirus: AVG Internet Security 2012, Updated and Enabled
So here's my setup:Computer A is connected directly to a cable modem box via USB. Computer B (which is sometimes a laptop and sometimes a desktop) is connected to Computer A and shares its internet connection via Ethernet because I am too cheap to buy a router.A few days ago we borrowed a Belkin wireless router so we could have both desktops, the laptop, and my fiance's iPod Touch access the internet at the same time. That worked fine but once we returned the router and tried to put everything back to normal, it didn't work. The only computer able to access the internet is Computer A (or whichever one is directly connected).I tried resetting the modem and restarting both machines. I tried disabling all of the connections that showed up from using the router.Windows states that the IP isn't properly configured or something of that nature. I tried setting it to automatically set the IP but to no avail.Here is the part that really confuses me - I can access Computer B from Computer A via LAN using the ethernet cable, so the connection between the two computers is fine.