Whenever I add devices in CiscoWorks and do not manually specify the device type. CiscoWorks find itself wrong device types for it, For example I have found that mostly it classify WS-C3750-48PS-S as below device types; [code]
Also found that WS-C3560-24PS-S discovered as 7600 series routers.
I have production stack in the following config:
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C3750-48P 12.2(25)SEE4 C3750-IPSERVICESK9-M
2 52 WS-C3750-48P 12.2(25)SEE4 C3750-IPSERVICESK9-M
I want to add 3-rd switch to it:
Switch: WS-C3750G-48PS 12.2(25)SEE3 C3750-IPSERVICESK9-M
Will this configuration work? My main concern is IOS difference?
I have 3750-48PS-S in production and would like to stack it with C3750G-48PS. Both switches are running code:
c3750-ipservicesk9-mz.122-50.SE3.bin
I have 3 ws-c3750-48ps in a stack and i'd like to enable dot1x on the stack I entered the commands: [code] I also have dot1x enabled on several interface on the 2nd and 3rd switches in the stack with these commands [code] dot1x successfully works on these ports and I see the logs in acs, heres where the problem comes in when i try to enable dot1x using the above commands on any interface on the first switch in the stack it doesn't work its like the switch doesn't support dot1x. I'm assuming that there is a bug in version 3 but after googling I didn't come up with much.
View 6 Replies View RelatedAfter powering up a WS-C3750-48PS switch, Normal POST LED flashing of lights does not happen, instead the switch is stuck in SYST Mode on the front panel. My attempt to hold down the mode button upon powering up for 15 sec fails to reboot the switch. I cannot console to the switch. Is this switch unrecoverable? Should I RMA with TAC?
View 5 Replies View RelatedI tried to discovery WS-C4507R+E devices with lms 4.0 but the devices result unknown, any package to install to discover these types of device?
View 1 Replies View RelatedI have a c3560 that on Port 1 I can not get any device to talk to the DHCP server.Previously there was a client connected to this port however over the weekend he stated he lost connectivity.
In my troubleshooting I have connected that client to another port and now he is good to go...I connected my laptop and tried to connect to the network however I could not.I checked the logs and did not see anything that lead me to think it was having problems.
Is there another way to shut this down and hopefully start it back up without having to restart the entire switch?
We have plans for multiple ISPs and need to pick the correct device/architecture for that. single site: 3 ethernet hand offs (1 From ATT Fiber/10Mb pipe via their managed router, another one from ATT via Copper T1 via a separate circuit & managed router and the 3rd/last from Cable Modem/Comcast)
1.WAN hand off from another ISP from I will use ASA 5510 (already have) to use all the above 4 as inputs and then use the internal interface of the ASA 5510 as the default gateway for all the employees to browse the internet etc. so that1. If one one or more of the ISP lines die, we continue to operate (albeit lower bandwidth)
2. Also, we take advantage of the added bandwidth (even though it may not be the arithmetic sum of all the above).
I have tried Cisco presales but got bounced - go Cisco !So, i have a small customer who requires a single device which will provide .....
1/ Leased Line connection @ 10mb
2/ ADSL failover onbox (so configurable from CLI, unlike the 860’s which I see only have one ‘active’ wan port)
3/ IOS based
4/ integrated 4 ports (min) switch
5/ site to site VPN
6/ up to 10 x SSLVPN remote users
I did pitch in with ASA5505 with external ADSL router but he is “space-constrained”.It worries me when Cisco doc's say only one WAN port is 'active' - since it doesn't say the second port automatically comes up if the first goes down so I can't take a gamble on that being the case.
I have LMS 4.0 server installed without any problems on windows server Enterprise edition service pack 2 then i enabled SNMP on cisco switches and routers by the following commands [code] But when i tried to discover cisco devices and after trying many times theres no result so correct commands required to be enabled on cisco devices.
View 2 Replies View RelatedNCS 1.1.1.24 (PRIME-NCS-VAPL)
5508-50 WLC 7.0.235.3
I had to re-IP this WLC onto another management vlan. Prior to the IP change and code upgrade I removed the WLC from NCS.When attempting to re-add the WLC to NCS, I finally found the it in Configure>Unknown Devices. Now NCS is showing the Device Type as Unknown, and Inventory Status Detail as Unsupported device, and reachable.
I have a team onsite this week inspecting us. We found out yesterday that Retina is unable to access several of our switches. Said switches are able to be pinged from workstations on both of our main VLANs, I can SSH to them from any computer which is included in the ACL (and yes, the Retina server is in the ACL). Users can login to and access all network resources without issue. Each switch is configured with a management IP on the same VLAN. I have created a full-permissions user on each switch specifically for scanning use.
All switches are running the same code (12.2(58)se2). I was just able to SSH from one switch to another (with the user account made for the Retina scan), all through the stack of switches experiencing the problem. While doing so, I did a how log | incl <IP of the Retina server>. 90% of the switches had no records for that IP (thus no attempted connections). The few that did have record of it, reflected a connection over 24 hours ago- and we've just tried it several times within the last 6 hours (it was 0300 when I sent this email to coworkers that I'm snipping into this post).
We have a PIX firewall 515E running version 6.3(4) and there are few site to site VPN's installed on it. We want to find out the isakmp key for those VPN tunnels. On ASA, We can run the command "more system..." and it displays the key, but it seems it doesn't work on the PIX 515E.
View 1 Replies View Relatedi'm currently deploying LMS 4.2.3 Demo version and i'm unable to discover my ASA 5510.how to discover my ASA to mange it in my Cisco Works 4.2.3.
View 35 Replies View RelatedWe have an ASR1006 and I'm just discovering net flow aggregation cache.
I tried prefix aggregation and worked fine. But i cant get any information when checking AS aggregation. All I get is 0 in source and destionation AS. [code]
I have a LMS 4.1 and ive enabled Energywise on several switches.I can see them on energywise devices. they are in the same domain and most of them have IP Phones and Access Points.there are 18 IP Phones registered to a CUCM which is seen by the LMS. and ive done a user tracking and ive seen the phones registered.the access points are LAPs and CAPs (1142, 1131, 3500).
when i try to enable the Energywise End Hosts, i cant see any of the end hosts of the switches.however, when i go on CLI, and see the energwise children, i see them all.
how many types of ip address are involved in the process of webbrowsing? internal external.
View 2 Replies View RelatedI need to connect three sites. I also need to support some roving PCs connecting to the sites via VPN. With the RV180, can I support multiple ptp vpn connects between them, and at the same time, have the roving PCs connect to the RV180s.
View 0 Replies View Relatedhow are load balancers classified? I did quite a bit a reading on the topic and found that the three basic types are switches,software based and hardware based. But what do global server load balancing,firewall load balancing etc refer to?Are these load balancing methods?
View 1 Replies View RelatedI have a combined modem/router that was supplied to me by my ISP, and I want to connect a second router (Linksys) to it, because we share internet with the backhouse and the one router does not reach far enough. All of the hardware is working, but I cannot get the Linksys router to connect to the internet. Here's the stats:
The main router is a SmartRG, Powered by ClearAccess Model: SR300N I'm not sure what other information here is pertinent.
The secondary router is Linksys Wireless-G Broadband Router Model: WRT54G
The main router works without a hitch, so that's not the problem. I have the second router connected through one of the output slots from the main router, into the internet connection slot in the Linksys. Even hardwiring a computer into the Linksys doesn't work, so it seems like the actual router itself isn't connected.
What are the different types of network cables
View 3 Replies View RelatedWhat are the differences between DSL and cable, what makes Cable and DSL diff? How do these different networks work? Also, speed ranges would be great. There's also T1 and T3 and such? How bout those diff kinds of networks?
View 6 Replies View RelatedI am trying to configure a Unified Wireless solutions with ACS 5.1 and am having trouble with the access policies. We have corporate laptops authenticating via PEAP and 7921 phones authenticating using EAP-FAST.
I have one access service configured to allow PEAP and authenticate against AD and another access service configured to allow EAP-FAST and authenticate the 7921 phones against the "internal user" database.
I have configured 2 service selection rules. Each one points to one of the access services. The only condition I have currently configured is the "protocol" field to be RADIUS. Because both the 7921 phones and the client laptops are generating RADIUS requests I can only have one EAP type working depending which rule is at the top. Because the RADIUS protocol field is always matched, requests never get past the first rule.
how I modify the rule to be able to distinguis between VoIP handsets on one WLAN and client laaptops on another so that correct access policy is used for each device?
I have a small wireless network, which consists of three AP1121G with c1100-k9w7-mx.123-8.JEB1 ios and one 871w with c870-advipservicesk9-mz.124-24.T1. I've configured two different ssid's with individual authorisation types - ssid_1 with eap, ssid_2 with wpa. All three ap's works as it should be, but 871w authorises only eap connections, and all other types are rejected
View 3 Replies View RelatedI have a belkin wireless router and want to block the ability to download .exe and .zip files on my kids computers. Is this possible to block file downloads on only a few machines on my home network?
View 1 Replies View RelatedHow to specify the modern devices that are changed from wired to wireless devices at present.
View 1 Replies View RelatedMy wife's laptop will disconnect from our ATT Netscape router/dsl modem. The error we get is that the "security types do not match" ultimately we have to reboot the router and then her laptop will connect for a while. (we do not have this problem with any other devices that use this wifi connection.
View 1 Replies View RelatedRegion : Canada
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
I'm having a problem with my PlayStation and Xbox online gaming. my NAT types are too strict to play some games at all and when i set up my network connection i have a NAT type 3. I am not very handy with networking to fix my problem.
I put a config on this switch and it is having some issues I would like to take it back to out of the box state however I am not sure how to do this ? I do not need to blow away the IOS just the config I put on it
Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(50)SE5, RELE
ASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 28-Sep-10 13:21 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02900000
[code]....
I am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not. Also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Any other way to update it. Master switch has new boot path but unable to change in slaves.
View 2 Replies View RelatedWe recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
View 3 Replies View RelatedI've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
I want to upgrade the IOS version of 3750 48PS switches. these stacks are located on different building some of the them having 2 members and some have 3 members in a stack.step by step to upgrade the IOS of these switches.
View 1 Replies View Related
