Cisco Wireless :: 4402 Version 7.0.116 - Free Memory Of System Below 100MB
Jul 31, 2011
4402's been running quite happily until recently. I have 11 wlan's configured, but only 5 are enabled at this moment in time.
There are 26ap's connected to the 4402, a mixture of 1130's and 1142's. The memory error in the subject is popping up quite frequently.
No reference I can find on this forum or other Cisco.com.
*osapiReaper: Aug 01 14:35:07.004: %OSAPI-1-MEM_LEAK_LOW_ALARM: osapi_task.c:5105 Free System Memory went below 100MB
*osapiReaper: Aug 01 14:34:56.996: %OSAPI-1-MEM_LEAK_LOW_ALARM: osapi_task.c:5105 Free System Memory went below 100MB
*osapiReaper: Aug 01 14:34:46.988: %OSAPI-1-MEM_LEAK_LOW_ALARM: osapi_task.c:5105 Free System Memory(code)
View 2 Replies
ADVERTISEMENT
Aug 29, 2012
From what I can see on some of the message discussion boards, this is an alert only message. I would like to get clarification that this will not cause operational issues with the controller.
I did try to change the free memory by using the command
config memory monitor leaks 10000 300000
but then I get a response about core dumps and the alerts do not go away.
View 5 Replies
View Related
Feb 18, 2013
I face frequent reboot on this controller. Below is the crash report.
Beginning of Crash File: mwar_dump2.crash
************************************************************
* Dumping Registers *
************************************************************
NIP: 1000C0F4 XER: 20000000 LR: 1000C090 SP: 3B96BC50 REGS: 0x3b96b790 TRAP: 0300
[Code].....
View 1 Replies
View Related
Mar 29, 2013
My Pix seems to have a memory leak ?
Result of the command: "sh memory"
Free memory: 6088072 bytes ( 9%)
Used memory: 61020792 bytes (91%)
------------- ----------------
Total memory: 67108864 bytes (100%)
This is 30mins after a restart. Seem like it gets worse and worse until i cant even connect to the ASDM.
I have Tried turning off loggin as well as some connection timeout commands.
View 1 Replies
View Related
Mar 6, 2012
LAP join process: 70:ca:9b:25:5b:9d -> AP MAC10.10.1.30 -> DNS
View 8 Replies
View Related
Jun 5, 2012
We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
View 3 Replies
View Related
Dec 4, 2011
I am running a WLC 4402 with software version 6.0.182.0. Which WCS version should I use or does it matter?
View 5 Replies
View Related
Jan 24, 2013
I would like to upgrade our three WLC 4402 controllers from version 7.0.116.0 to 7.0.235.3. I have downloaded the two files (AIR-WLC4400-K9-7-0-235-3-ER.aes and AIR-WLC4400-K9-7-0-235-3.aes). Which one should I upgrade/install first?
View 4 Replies
View Related
Nov 15, 2011
Recently, I have increase to 4G memory ram to the router 3945 but when I show version, it does not state there are 4G in there but still showing the old mem ram size. Why is that so ?
View 3 Replies
View Related
Oct 15, 2004
I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
View 9 Replies
View Related
Apr 20, 2011
Does anyone know of a system that works like an internal version of Akamai? I'm looking to be able to distribute content from different locations across our network (with one URL) and I'm looking for an elegant way of doing so. Is there a product out there that does this sort of thing already?
View 7 Replies
View Related
Mar 5, 2013
I have ordered RP2 and it will be having 8GB default memory. What is the difference between memory & Physical memory?Since I am able to see only 4GB memory in my ASR 1004. [code]
View 1 Replies
View Related
Aug 14, 2012
Is there a big difference in operating AP's when they are uplinked at 100mb vs 1000mb? We have 2 "main" offices that have AP's that are all connected to our access switches at 100mb. Recently with the addition of mobile devices, phones, etc we are seeing some issues. Today, we had a meeting room that had 20+ people connected to one AP and they started seeing issues of people getting disconncted or unable to connect.Just wondering if the uplink could have anything to do with this, or if we are just over subscribing the APs?
View 5 Replies
View Related
Sep 14, 2009
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies
View Related
Mar 11, 2013
which version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies
View Related
Feb 20, 2012
I want to know which router can be used on 100mb cable connectionThe router will be using the connection from cable modem on bridge mode/modem mode with eth to routerI kind of have a idea looking at performance ratings but ppl have mixed opinions when you enable NAT and ACLs etc etc285129013825.
View 5 Replies
View Related
Aug 16, 2011
you have a Cable Modem and are paying for 30MB/sec download or better service, but the network connection on the cable modem is only 10/100; all very common today.Your network connection is showing it's connected at 100 (computer - router - cable modem)....now on the technical side, remember that a 100 MB network connection can only transfer data at a maximum rate of 12.5 MB/sec (not something the normal home user knows or even thinks about).So here's the question; why would you pay for 30MB/sec download speeds when the cable modem itself can only transfer (in theory) 12.5MB/sec to you over the network?
View 3 Replies
View Related
Nov 29, 2011
I'm looking into upgrading my WAN link to 100Mb via Fast Ethernet link. I'm waiting to hear from ISP about what exact technology they use, but according to my manager they will be coming in over fiber and then terminate to copper. I currently have 2811 in production with two T1 cards bundled together. 2811 has basic configuration with only 2 ACLs. I have ASA 5510 for NAT, Ipsec and other services. What router or networking device (layer 3 switch, such as 3560G perhaps??) should I use to accomodate 100Mb link? It seems that 2811 will not handle that kind of bandwith..In short the max recommended bandwidth limits for the 28xx series are as follows:
2801--2 Mbps
2811-4 Mbps
2821-8 Mbps
2851-12 Mbps
I don't want to create a bottleneck and am looking for appropiate solution to accomodate 100Mb link. Also, could ASA 5510 become a bottleneck in my scenario?According to Cisco docs ASA5510 can handle 300Mbps of firewall througput, but I'm not sure how it'd work in production...
View 1 Replies
View Related
Sep 30, 2011
if i plug a cisco 880 router in to a 100MB WAN Ethernet circuit what throughput will i get? on cisco site it says 25mb/sec but if it is Ethernet shouldn't it be done in hardware and get the full 100mb/sec?
I know that a 1841 plugged in to a 40MB WAN circuit can match that speed but Cisco site say it only can do E1 speed.
View 3 Replies
View Related
Nov 27, 2011
I have three ESW-540-24 10/100/1000 Switches in a small school environment
1. ESW performs as a server switch for out small cluster of VMWare ESXi Hosts and iSCSI SAN with a link-aggregation/lacp/etherchannel connection to the backbone switch, and a Link-Aggregated Connection to the thrid ESW switch via a multimode optic fibre link to a near-site backup and DR location
2. The second ESW acting as network backbone links back to the server switch and our older LinksysSRW224G4 (four SRW224G4s) switches using Aggregated Links / LACP to reduce bandwidth contention and allow for link redundancy
3. The third ESW as mentioned previously is at the backup DR location linked back to Switch 1
When using Single 1GB links between these three switches I can almost saturate the 1GB link (80-95% utilisation) as soon as link aggregation is configured by bonding 2x 1GB links together to form an etherchannel link utilisation will not exceed 100MB (network monitor graph on a server/ workstation runs flat at 10% utilisation) I have tested this multiple times useing large file transfers accross our SANs (which have high enough throughput to saturate links) and can confirm that performance degradation occurs as soon as an etherchannel is configured on the same ports (regardless of manually setting admin speed and duplex of copper ports etc) all indicators specify that ports are running at 1GB even though throughput REDUCES by 90%.
We are not running the latest firmware yet (2.0.3), however I have read the release notes for newer versions (2.1.16 and 2.1.19) and there is no indication of a fix for etherchannel/lacp performance issues.
View 5 Replies
View Related
Nov 6, 2012
So I recently got a new computer today and it won't let me use my 100mbps of internet bandwidth. (Asus Sabertooth Z77 with an Intel 82579v gigabit lan controller) I noticed that at the LAN connection properties>Properties>Configure>Link Speed tab the 'Speed and Duplex' option was on Auto Negotiation and it was only accepting (or supporting) the 10mbps Full Duplex. When I switched it to 100mbps Full Duplex it would mark my connection icon with a red cross and when I clicked diagnose it said "Please connect your ethernet cable or your cable might be broken". So I tested my internet speed with that same cable on a different computer (laptop) and it worked with 40Mbps, so I don't think the cable is broken. Also I just recently downloaded some drivers but one was specifically for the Intel LAN controller but I'm a total noob for all of this computer stuff I don't know if it messed it up or something. Is it the motherboard that's not working correctly?
View 3 Replies
View Related
Jun 4, 2012
I have a Cisco WRVS4400N on the latest firmware and I have just had my Virgin internet connection upgraded to the 100Mb. Once i thought it was upgraded i checked with a broadband speed test and it came back as 15Mb download and 5Mb upload. Before i rang Virgin i thought i'd check with a direct connection from my pc straight to the modem. Ran the speed test and it came back as 100Mb download and 5Mb upload. I thought the best thing to do is restore my settings back to factory and its still the same.
View 7 Replies
View Related
Jun 4, 2013
I'm trying to configure and etherchannel between 2 switches. A 3750 and a 3750G, but the port channel is down: 3750. [code]
View 2 Replies
View Related
Feb 24, 2013
Am trying to joing a Joining SF 300-48P 10/100mb Switch to a SRW2038 Gigabit Switch,
I purchased a "Cisco SFP+ Copper Twinax Cable - Twinaxial cable - SFP+ - SFP+ - 1 m" but I am uable to get connection
View 1 Replies
View Related
Sep 4, 2012
I have a c3560 switch that has two gig fiber modules in it. I need to uplink fiber to one of these at 100mb. This is because this port will be rate limited to 20mb and 10 percent is the lowest you can go with the rate limiting command. Is there a 100mb fiber module i can insert in the 3560
View 1 Replies
View Related
Jan 19, 2011
My ADSL light switches off randomly during downloading a 100mb file. I just cannot complete the download. This has been happening ever since I switched my router to a wireless iBall Baton 150M.
View 9 Replies
View Related
Nov 28, 2011
I am assuming, that the slowest component on a network determines the connect speed? I am having a small network with 4 pcs and 2 of them show 1GB connect speed while the other 2 show 100MB. What would cause 2 units to run at the 100MB speed on a Gigabyte-Switch and Router?
View 3 Replies
View Related
Jul 8, 2012
Our network administrator restricts all our new 1Gb switches to only 100Mb, to which he claims it will increase overall performance. Preventing devices from bottlenecking the network. (that is, only restricting the main switch ports, not the uplinks)For example we have a new building with 2x WS-C2960S-48TS-L connected together with FlexJack and then a 1Gb Fiber connection back to our core switch.
This building is on it's own subnet and there is little broadcast traffic. I don't see the point other than it hinders the potential speed we could use. Labs are set up in this building and 1Gb is MUCH faster when it comes to imaging and software deployment.
View 8 Replies
View Related
Jan 16, 2012
Can we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies
View Related
Apr 3, 2012
provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies
View Related
Nov 1, 2011
Can 't connect to the free internet connection, but can on secured and that one have weak signal. What is problem?
View 7 Replies
View Related
Jan 13, 2012
Is there a wireless router available that will support a free dynamic DNS provider such as [URL], without the need for custom firmware?
I have a device that requires DDNS, and I do not want to mess with firmware updates. I've already bricked a router trying to do that. So I'm looking for a replacement router that requires little to no modifications to use a free DDNS provider.
View 1 Replies
View Related
Nov 15, 2011
alfa free downloading wireless usb adapter
View 3 Replies
View Related
