Cisco Wireless :: Can't Access AP1242
Aug 28, 2012I have a brand new AP1242.. the issue is that i can't access it by Console nor by GUI on it's default IP Address 10.0.0.1.
View 0 Replies
ADVERTISEMENT
Cisco Wireless :: Do AP1242 Access Points Support Kron Commands
Sep 22, 2010Do AP1242 access points support Kron commands?
View 4 Replies View RelatedCisco Wireless :: Recognize Attached Antenna To AP1242
Nov 11, 2012Im looking for possibilities to remote recognize attached antennas to AP1242. I have a lot of devices which not working properly. I think most of them have only one antennas installed , but I cant be sure if its fitted into primary connector. Do You have any idea how to check numbers of attached antennas and if only one if its fitted into primary connector?
I want to disable diversity when I'll find APs with only one antennas.
Cisco Wireless :: AP1242 Excessive Transmit Discards And Performance Complaints
Apr 15, 2013I have an AP1242 near a couple of conference rooms. I get complaints when we have a large contingent in there and some try to download documents. The bandwidth consumption is meage - less than 2Mbps. But there could be say 50 people in those training rooms. I see no errors at the FE interface on the AP but I do see a good number of Transmit Discards.
Are 50 users connected to an AP1242 simply more than should be expected of the device? 802.11g is the radio.
Are transmit discards indicative of some kind of configuration problem? The users in these cases are generally very close to the access point - within a few feet even.
If it is indicative of a configuration problem would that be an issue of the configuration of the laptop wifi cards or a problem at the AP?
Cisco Wireless :: Ap1242 Rebooting Every 5 Minutes / Crashinfo Files Generated
May 3, 2012I have 1242 Configured with 12.4.21a-ja1 and I have many of these. however I have 4 on the same location that have just started rebooting. The crashinfo logs ell me that cmd: PASSWORD statement not printed..Dont know if thats the issue....but something is wrong.. We are running SNMP and thats about it...
View 1 Replies View RelatedCisco Wireless :: AP1242 - Privileged Exec Password Works For Telnet But Not Web Interface
Jul 12, 2012I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything. I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.I've tried a different browser - login box continues to pop.I've made sure the web interface is activated in the API've tried a differnet computerI've tried disabling password-encryption service. Reset the enable password , I've successfully setup other 1240 APs but must have done something wrong on this one.
Cisco :: AP1242 In Autonomous Mode?
Dec 21, 2011I am in the process of configuring Network Access Protection and just found out you can apply user based ACLs in the Network Policy. Will this work with a Cisco AP1242 in Autonomous mode? I saw some configuration guides for configuring User ACLs using the wireless controllers but not just Radius.
I have added the Vendor Specific Attribute of "Cisco-AV-Pair with two values of
-priv-lvl=15
-ip:inacl#10=deny icmp any any
I would expect all traffic to be denied when the user logs in due to the explict deny at the end of an ACL but I am not seeing that so I was unsure if Per-User ACLs work on standalone AP1240s.
I could add another rule to allow other traffic but I just want to see if the ACL would apply on a per-user/per-session bassis on the AP1200.
Cisco :: AP1242 Ag As A Supplicant On Interface Switch
Jul 15, 2012How to configure LAP 1242AG to authenticate it self as a supplicante on the 802.1x interface switch ?
View 5 Replies View RelatedCisco :: Ap1242 - Bridge Connectivity Failing
Jan 14, 2013I am having trouble getting the bridge to work. The setting is as follows: I have to buildings, separated by a road. Distance is apx 35-40 meters. From the main building there is a network which I am trying to extend to the other building by a wireless bridge. I am using two 1242 (autonomous) for this. I have also external directional antennas (7Db) mounted on a pole 8 meters above ground on each buildings. These are of course directed to eachother. The antennacabel used between the ap's are shielded Cisco-cables.
The config on the root AP:
dot11 ssid Valhalla01
authentication open
authentication key-management wpa version 1
[Code].....
Use A Netgear Wireless Card To Access Belkin Wireless Access Point?
Dec 23, 2012have netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View RelatedCisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?
May 9, 2012I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
Cisco Wireless :: 5500 - Limiting Access To The Boardroom Access Point
Jun 4, 2013I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
Linksys Wireless Router :: E1200 - Access Restrictions Change To Access Policy?
Feb 25, 2013What happen to my router linksys e1200, after i update the firmware to the latest version "Access Restrictions" is change to "Access Policy". how can i revert it back to "Access Restrictions" do i need to downgrade the firmware?
View 2 Replies View RelatedLinksys Wireless Router :: E2000 - Access Restriction Shuts Down Access To All Computer
Jan 1, 2013I have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
Laptop Cannot Access Home Wireless - Can Access Elsewhere And Other Computers Are On It
Jul 27, 2011I have a new laptop that cannot access my home wireless. There are 3 other computers that can access it so I know it's working. When I work away the new laptop can access other wireless connections. But as soon as I get home it's stuck on 'acquiring network address'. The weird thing is my kindle does the same thing as does my friends iphones & ipads. They all connect wireless no problems elsewhere but cannot at my house.
I've tried switching off the other others computers connections & trying to connect. Resetting the router
Cisco Wireless :: 5508WLC Whitelist For Guest Access And Securing Guest-access?
Aug 18, 2011Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedCisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point
Apr 20, 2012I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedLinksys Access Point :: Cannot Access Configuration Page For WAP11 Access
Jun 12, 2007Cannot access configuration page for WAP11 Access
View 9 Replies View RelatedCisco Wireless :: 5508 Internet Both Wired And Wireless / Access To Server Everything Dead
Oct 24, 2011have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedCisco Wireless :: 2500 / 5500 - Wireless Access Point Identification By Clients
Apr 30, 2012We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
Cisco Wireless :: Can Access Point AP541N Connect To Wireless Clients
Aug 10, 2010Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?
View 1 Replies View RelatedCisco Wireless :: Manually Add Access Point To 2504 Wireless Controller
Sep 18, 2012We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
Cisco Wireless :: Setting Up Wireless Repeater Using 1242AG Access Points?
Jul 4, 2011I have problem setting up wireless repeater using Cisco 1242AG access points. Here is the setup and problem - The location has 2 1242AG APs and a WLC (2206) which will be used by PDAs. One of the AP was converted to Lightweight AP and is wired. This AP is up and working and PDAs are able to connect to it. There is 1 WLAN and it uses Local EAP (LEAP) as authentication. Layer-2 security is configured as WPA/WPA-2 with 802.1X authentication. Under AAA servers Local-EAP is enabled and a profile (with LEAP enabled) is used. Local users are configured for login. As said PDAs are able to connect and it is working without any problem.
WLC (LEAP with local users) -----> LAP ----> Repeater AP
But the 2nd AP has to be configured as repeater was configured to repeater mode (refering to the document) and was placed. The WLC can see a client (with APs MAC address) but it is probing. The AP is still Automonous AP. Also username and password is configured for authentication. But still the radio on the AP is not up and it is in reset state.
Cisco Wireless :: 802.11ac Module For Wireless Access Point 3602?
Apr 3, 2013Is 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies View RelatedCisco Wireless :: WET200 Like Access Point Cannot Reach Internet From Wireless
Sep 26, 2012I have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
Linksys Wireless Router :: Does Cisco WAP4410N Wireless-N Access Point Support PPPoE
Feb 21, 2013Does Cisco WAP4410N Wireless-N Access Point support PPPoE ?If yes how can I configure the PPPoE conexion?
View 1 Replies View RelatedCisco Wireless :: WCL 5508 - Cannot Access Https To Wireless Controller
Apr 15, 2012Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies View RelatedCisco Wireless :: How To Create Guest Access In Wireless By WISM V 7.0 And WCS And ACS
Oct 6, 2012how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?
View 1 Replies View RelatedCisco Wireless :: 4402 Access Points Without Wireless LAN Controller
May 8, 2012I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?
View 2 Replies View RelatedCisco Wireless :: Wireless Access Points Recommendation 3600
Mar 12, 2013We are planning to upgrade our current wireless access points (1200 series) to 3600 series. We would also like to add a wireless access controller to the design to centrally managed those Access Points.
Which Cisco Controller model support those 3600 APs efficiently?
Cisco Wireless :: Best Method With AP541N For Guest Wireless Access
Nov 1, 2011I have a client that has 3 AP541N's and they want to enable guest wireless access. However, their VOIP provider has their managed switches locked down so we can't add VLANs, etc.So I cannot touch the switch or router config on this LAN.
Looking into AP541N documentation I see VAPs mentioned, can I enable those and have secure guest wireless access with the same private IPs that the rest of the LAN use right now? (That is, the employees are 192.168.2.x and the guest wireless users would also be 192.168.2.x.)
Or do I need to do something else to properly enable guest wireless? Like add another piece of equipment? I did try to add a Cisco RVS4000 to the mix but it wouldn't pass the VLAN across the switches that I setup for the guest wireless SSID. goal is to leave the switch and router in place, and work with the AP541N's that I have and get secure guest wireless.
Cisco Wireless :: WRVS4400N Can't Access Wireless Link
Feb 21, 2011We have purchased a CISCO WRVS4400N from PARTH TECHNOCOMM, KOLKATA and the service engineer already installated on 01/02/2011 but we have facing the folloing problems :
1. We can not access the wireless link in and arround the three storied building.
2. We can not able to prevent the access the link as it is required. The system has no add device option so any wireless laptop users can access our link without our permission.
Cisco Switches :: SG-200 Access Point Is Only Able To Access Internet / When It Is Plugged Into Port
Jun 22, 2012I'm having some difficulties with the VLAN setup on the SG-200 and the WiFi access point. The access point (a TP-Link WA801N) is only able to access the internet when it is plugged into a port that is on the default VLAN (PVID 1). If I plug it into one of the other VLANs then any clients connected to the WiFi lose access to the internet and cannot access devices on the VLAN. I have previously used this setup with a first generation Cisco WAP4410N. [code]
View 4 Replies View Related