Cisco Wireless :: WRVS4400N Can't Access Wireless Link
Feb 21, 2011
We have purchased a CISCO WRVS4400N from PARTH TECHNOCOMM, KOLKATA and the service engineer already installated on 01/02/2011 but we have facing the folloing problems :
1. We can not access the wireless link in and arround the three storied building.
2. We can not able to prevent the access the link as it is required. The system has no add device option so any wireless laptop users can access our link without our permission.
View 1 Replies
ADVERTISEMENT
Jul 18, 2012
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
View 4 Replies
View Related
Mar 10, 2012
When clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server. After they have the address they can no longer access the server. It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS. The WRVS4400N is setup for DCHP relay to the server. Wired clients do not have this problem. Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem. I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch. Turning the server firewall off has not made any difference either. I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options.
View 5 Replies
View Related
Apr 9, 2012
I am using WRVS4400N in our company as a AP only. Before some time, when majority of wireless clients were computers, everything worked fine. But now, when mobile devices are in majority, something strange is happening. While portable computers still work fine, smart phone and tablet have extreme problems.
Although there is indicator that WiFi is connected and signal is strong, there is no guarantee that there is an internet access. Most of the times there is none. You can fix this by simply disconnecting and connecting WiFi on mobile device, but after a while, internet will be inaccessible again. Or you can wait and eventually you'll get to the internet access again.
View 6 Replies
View Related
Jun 18, 2008
I have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...
View 5 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Nov 11, 2010
WRVS4400N with firmware version V2.0.0.8.
After about an hour it routinely drops wireless clients. Wired clients are fine.
Re initiating a connection from the clients usually restores the connection fine. Sometimes this is just doing something to force the client to use the connection for some active function other times it's forcing the client to renew it's DHCP address or power cycling the client. The same experience is happening with a TioVo on WiFi, an iPhone on WiFi, and a WAP4410N in Client Bridge mode.
While this may not sound that bad, it's creating 2 huge issues that shouldn't occur.
First, the wireless clients that are dropped are not accessible from other clients on the network until they reestablish their connection. There is no indication on the client of an issue with the connection. For example, a TiVo connected over WiFi isn't accessible from the network until it reestablishes it's connection. It works fine then for a hour or so.
Second, for the WAP4410N (firmware 2.0.3.3) in Client Bridge mode, this client requires a power cycle to reconnect to the network. In much less than an hour it stops responding to it's IP address for it's management page, but continues to pass traffic from the multiple wired items it's bridging. Then, after about that same hour, it stops passing this traffic too.
I tried running the WAP4410N in WDS Bridge mode but was unable to get it to work. For this testing, access to the management page was the test with no devices behind it. So, it's possible that that access is what was broken and that it may have passed traffic. No wireless clients need to connect to the WAP4410N, just the bridged wired clients.
This WAP4410N was previously acting as a brige to a WRT54G with no issues, but at G speeds. Which makes me think it's an issue with the WRVS4400N dropping clients and the clients not knowing it.
View 10 Replies
View Related
Apr 21, 2012
After a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
View 1 Replies
View Related
Apr 24, 2012
I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies
View Related
Jul 6, 2012
My ip address of my WRVS4400N changes every so often. when i use the ip assigned to connect remotely, it works until the ip is re-assigned through dhcp. I know there is a way around this bu ysing a name or something. I just don't know how to set that up.
View 1 Replies
View Related
Apr 23, 2012
I have a WRVS4400n and a CentOS server that I need to enable a SSH access to from WAN. I created a single port forward rule to open port 22 and forward to server (which address is 192.168.41.3) However ssh connect doesn't happen, the command "ssh user@{external_IP}" times out after 20 seconds. If I connect my server directly to modem through outside interface - I have no problems connecting to it. Once it's behind router - no luck. I even added same rule for UDP, not sure if it's needed, but it definitely didn't hepl. The router is on firmware version 2.0.1.3, version on a bottom is 2.
View 4 Replies
View Related
Oct 7, 2011
I have a WRVS4400N, and need to apply access control to an IPSec tunnel that terminates at a client site, but can't seem to make the device comply.
I can configure ACLs on their device for the LAN to restrict packets coming back into my network, and can restrict packets outbound frm my LAN but that is hardly a secure method of doing this in my opinion.
View 1 Replies
View Related
Aug 8, 2011
After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.
View 1 Replies
View Related
Oct 17, 2011
I recently bought a new Cisco WRVS4400N router for our network which has 19 computers connected to a 24 port switch. We are currently using a D-Link router and are upgrading to the Cisco router. The problem I am having is as soon as I connect one of our servers or the 24 port switch to the Cisco router I can no longer access the internet or login on the network, I also cannot access the routers setup from either server. If I connect the router to just a stand alone computer I can access the setup and change things but as soon as I connect the server or 24 port switch everything dies (all lights are still green on the router though so everything is connected).
View 1 Replies
View Related
Jun 23, 2012
I am trying to create an IAP for a single computer based on it's MAC address. I want to block certain keywords and websites 24/7. When I setup the IAP as number 1, I add the MAC address of the computer in question. I then Select Allow and choose Everyday and 24 Hours. I type in the forbidden domains and click add after each one. I type in the keywords and click add after each one. After I click on Save, all of my computers on the network lose internet access.
I have WRVS4400N VPN Version 2, firmware version 2.0.2.1
View 2 Replies
View Related
Jan 18, 2013
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
View 3 Replies
View Related
Jul 2, 2012
I am connected to my TP-Link Wireless N AP via wireless on my laptop. The AP is set to the Wireless AP config but I have forgotten the wireless key i defined when i configured Wireless AP, so therefor cannot successfully connect any other device to the network. The key has been saved on the computer its connected to via wireless (my laptop) and I was wodering if i could use this fact or any other method of recovering the key? I am using Win Vista on this system.
View 3 Replies
View Related
May 12, 2010
I hardly try to get WDS running with two WRVS4400N v2.The manual (and the web interface) says: "Note: The WDS feature allows WRVS4400N to connect with up to 3 wireless repeaters that can be either WRVS4400N or WAP200." But I wasn't successful by now in getting it working..What I've done so far:
- Setup the primary WRVS as Gateway, WAN through Modem, LAN and WLAN using WPA2 Personal Mixed, DHCP
- works perfect
- Setup the second WRVS as Router using the same WLAN settings, no WAN and no DHCP
- Enabling WDS on both WRVS, giving each the MAC address of the other
- no connection to LAN or WAN through the second WRVS
I really need the second WRVS act like a bridge. Since the manual is saying that I can connect both devices through WDS I bought two of them. On the other hand I've now read somewhere in the community, that this isn't possible with two WRVS (?)
View 6 Replies
View Related
Nov 22, 2011
I've got an out of the box WRVS4400N and it will not pick up a DHCP IP from the ISP.
I reset to factory defaults, tried another ISP, returned and got a second wrvs4400n all the same results - no IP address on the WAN port. The internet LEDs are blinking but no IP on WAN port and no internet connection from a laptop connected to wrvs4400n.
I even tried turning of the firewall too.
Is there something with these routers that needs to be done for internet access?
Most typical small routers are just set up as a DHCP client on the WAN side and DHCP server on the LAN side.
View 2 Replies
View Related
Feb 15, 2013
In the note, i ve seen we can configure a WDS with 2 WRVS4400N, but i can't.How can i configure the 2nd WRVS4400N as repeater? Or can i configure it as Access point for another modem ?
View 1 Replies
View Related
Nov 29, 2011
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.
View 1 Replies
View Related
Jan 11, 2011
I am using a WRVS4400N as my primary router for a small office. I get the following message repeated over and over in my logs. This seems to happen for 2 or 3 days and then it will go away for about a week and then come back. What is causing this? The best I can tell I don't have any IP conflicts on the network and most of the time the network has very little traffic other than 2 or 3 computers surfing the web. [code]
View 19 Replies
View Related
Jul 14, 2009
I am having some problems with WRVS4400N v2.We use it just for wired network (wireless is not in use, but it is configured). As a WAN we use PPPoE. Most machines do not use DHCP.After a while (few hours to few days after power up) the router freezes and it is not accessible. I cannot ping it or access to the admin page.I have the latest firmware version (V1.00.09-ETSI)I also called service and they suggested to reset it to factory settings and reconfigure it.
View 3 Replies
View Related
Oct 20, 2009
Ik have a 50MB/s internet connection and my IPS provider's modem out is indeen 50MB/s
Per port from my router i do not get more than 20 to 23 MB/s ou tof it.
View 2 Replies
View Related
Jan 2, 2013
I have an older Linksys WRVS4400N Version 1.1 VPN Router. I have it set to run in mixed mode G/N. I still can only get connection speeds of 54 Mbps though. How can I get my wireless N clients to see 300 Mbps speeds?
View 1 Replies
View Related
Jun 1, 2010
I have a D-Link DSL-320B ADSL2+ Ethernet modem that connects to the internet fine if I am using just 1 computer. However I have bought a Cisco WRVS4400N to enable me to get all of the other computers at home on the network (wired and wireless).
The WRVS4400N picks up a WAN address from the D-Link BUT I just cannot get an internet connection, just "Local" only. I have tried setting it up as a gateway, as a router, upgraded the firmware but it just is not having it. My previous experience with routers has been just to plug em in and let them get on with it. The WRVS4400N is proving very troublesome.
View 8 Replies
View Related
Dec 24, 2010
I am have a lot of difficulty getting my WET610N to connect to my WRVS4400N. I have tried almost everything. I have some older PC's, as well as my PS3, that we use to use on the network and they only connect B/G. I have tried auto DHCP and static IP on the bridge. It seems that the only way that the bridge works is by using the WPS function that the business class routers do not have.
View 1 Replies
View Related
Aug 30, 2012
Now that Comcast is in the process of rolling out IPv^ to their customers nationwide, will there be a firmware update that properly displays the IPv6 /64 address as provided by the cable provider? Currently the only IPv6 address displayed is on the LAN page and is not configurable (greyed out) except for the prefix length. I already have a cable modem that will provide both IPv4 and IPv6 addresses as they are rolled out.
Currently running WRVS4400N v2 fw 2.0.2.1
View 1 Replies
View Related
Jan 30, 2011
I wonder if there is any place in WRVS4400N where I can tell it to just be an Accesspoint?
I have a customer who have 8 sites and we don´t know if there is enough with one wireless router or if we need some AP as well.
If it´s possible to make the WRVS4400N to become an WAP4410N then we can by only one machine no matter what...
View 1 Replies
View Related
Jan 6, 2012
I have installed a WRVS4400N router in a client's office. When laptops are plugged into the router everything works fine. When they are attached via the wireless signal it drops frequently. WPA personal is being used to encrypt. I have also installed the latest firmware and am having the same results. What can be done to eliminate the drops?
View 10 Replies
View Related
Aug 19, 2012
I have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies
View Related
Jun 2, 2013
I need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies
View Related
Dec 15, 2011
All of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies
View Related
