This is regarding "Client link 2.0" in 3600 AP . It's a cool technology ,no doubt . But i am thinking on how to test in any labsetup . Can any tell me the ways to test the functioning of "Client link" technology with 3600 AP / the CLI commands .etc .?
View 1 Replieswhen this error occurs
we can't see the cdp neighbor and the wireless crash.
we login onto the ap with console , we can see the error log : “Network interrupt loop detected” . last forever
What is the maximum throughput of a 2600 AP when using CLient Link 2.0. I see that the datasheet states that it is 450mbps, however, from my understanding of transmit beamforming (client link 2.0), when traffic is "beamformed" to a client it cannot use spatial multiplexing on the same antenna as well. If this is the case, with the 2600 only having 3 transmit antennas, does this mean that the max throughput to a client when using clientlink is 300mb ?
If not, how the AP transmit at 450mbps and beamforms at the same time.
I have a problem with a WLC 2500 and 3602E the problem is the link speed between the AP and the client is weak and the client is close to the AP the version fo the WLC es 7.4 and don´t know if it is a bug with the version because if I use a autonomous AP the speed is good
View 6 Replies View RelatedRegion : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I am trying to get a windows 7 laptop to connect to a TD-W8970.
Region : Italy
Model : TL-WR702N
Hardware Version : Not Clear
Firmware Version :
Android Tablets do not connect to Wifi Ad Hoc network (IBSS).My Nokia phone create an HotSpot WiFi network type AD HOC (IBSS).With TL-WR702N in Bridge or Repeter i connect it to Nokia Phone in "Ad Hoc" mode and creare an AP Wifi infrastructure network that my Android Tablet can connect to it.
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
Region : India
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : 3.13.27 Build 121101 Rel.38183n
I have bought TP-Link TL-WR841N 300 mbps router. I have 20-25 wireless clients but only 15 wireless clients are able to connect to the router. Is there the limitation on numbers of wireless clients can connect to the router?
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
Region : Poland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I have some linksys router that I used as wireless client bridge. I have main router that is connected to Internet and linksys router which is connected to main router's WiFi. Linksys router acts as client bridge connecting LAN devices to main router. Now I own TL-WDR3600 and I would like to replace linksys router. How can I achieve the same on TP-Link router? I don't see any option for setting wireless operation mode.
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP :
I have an unused TD-W8151N. I also have a smart TV that requires a wired connection, with no way of getting a wire to it.
Can I configure my spare TD-W8151N as a client of the existing WiFi network and connect the TV in to the TD-W8151N with a cable?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
So I've been checking my router DHCP list and I usually use the WPS feature to add devices. I know how many devices I have and which ones are wireless etc. I've made address reservations on all the devices that I have and know of. One feature that really frustrates me (which is missing) is no way to rename a device. My iPhone is named: Reggie's iPhone yet the 4300 picks it up as Unknown... I dont understand why. I've renamed it on the iPhone to different things and restarted it but still it comes up as that. I have 2 Nexus 7s and both come up with wierd names, one is for my wife and one is for me and I wish there was a way to name it proper.
Question is: Will the name edit feature ever get added to it? I dont get why it's not there now, it's not really something major (I have a 5 year old router that even has that... and it cant even support N). It's really frustrating to have to guess and check the devices on my network because most of them come up as unknowns.
Right now I'm trying to located another device that's coming up as unknown and now matter how much I try, since the router lacks any feature to assist finding it, it's really frustrating.
something else i noticed: my DHCP List shows all the devices connected with their IP addresses, yet I went into CMD and was doing a random ping command. I'm able to ping 192.168.0.114 with perfect stats back yet on my DHCP List it shows the highest IP is at 192.168.0.112.... Is something wrong here? Is it supposed to not pick up the IPs it gives out? And of course since there isnt a way to tell if that IP is for a WIFI or ethernet device, I have no idea what that device is...
yet i found another ip address on my network by using the ping command. actually I went ahead and did arp -a to find out all the ips with mac addresses. this is a serious flaw with the security of this router!!
Region : UnitedStates
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP :
My TL-WR700N does its job to provide wired internet to my desktop computer from another wireless router via client mode. However, when it is connected, the other wireless clients connected to the primary router lose their connections. To restore those connections, the WR700N must be powered down and the primary router must be restarted.
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Am trying to use a TP-Link TL-WR702N to connect my Samsung SmartTV to a wireless network, using "client mode".For some reason, the TV refuses to accept it is connected, or even connected to a router. Enabling DHCP on the TP-Link does seem to convince the TV that it is connected to a router, but still not to the internet. Strangely though, I can control the TV via the Android app operating on the local network, so clearly it is connected. I assume the SmartTV is trying to get a response on the local network that the TP-Link is filtering out for some reason, but no idea why.
I have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies View RelatedI recently discovered the dd-wrt world and am attempting to make a wireless adapter for my Xbox360 using a D-Link DIR615 rev C1 router I purchased and linking it to my home wireless network router (also a D-Link DIR615 but rev B2). I successfully loaded the dd-wrt firmware onto the C1 router and have attempted (multiple times) to set it up for use with my 360 following the instructions posted here at the dd-wrt wiki posting. However, after following the instructions to the letter I have been unsuccessful. After setting it up I can get the router (connected via ethernet to my laptop) to "connect" but it lists the connection as connected to a "unidentified network" with no network access.
View 12 Replies View RelatedI'm just wondering why my computer is being associated twice before being secured and linked when it obtains an IP address from the DIR 655 router. I am using the DWA-552 wireless card to connect to it. When I first started using them together, this wasn't happening. Then, all of a sudden, one day it just started showing "above message repeated 1 times" just below the log entry for the client being associated".
View 5 Replies View RelatedIs there a client mode option for the DIR-655?I just got a nice cable modem/router from my ISP and I'd like to re-purpose my DIR-655.If I could turn a usb webcam, printer, or harddrive into wireless client, that would be cool. I would just rather re-purpose the device versus selling it.
View 2 Replies View RelatedI recently upgraded from a WRT54G and am having issues with a Win7 PC with wireless-N. Initially I had it configured static at 192.168.100.100 and everything worked, but the speeds were miserable (I followed all the forum posts and recommended settings). I noticed in the Status section of the router pages that the system showed up with the correct MAC address, but the IP showed as 192.168.100.10, which is the same as the router. Assuming this might be causing issues, I set a reservation for the system at .100 and set the client to use DHCP. However, now it won't pull an IP address at all. The status pages show the client with the correct MAC address, but an IP of 0.0.0.0. I've verified the MAC address a dozen times and rebooted the router and the client dozens of times with no change. Even when I removed the reservation, the system won't pick up an IP. I have a wireless-G client that's pulling an IP fine, so I know it's sort of working. The wired LAN is working fine, too. There are no IP conflicts, either. I changed DHCP to 'Always Broadcast (compatibility for some DHCP clients), but no change there, either. The client sees the network and still has a good signal, but just won't grab an IP.
I'm running Hardware Version: B1 / Firmware Version: 2.01NA
Is it possible to de-auth a client, and then make sure they have to enter the passphrase if they want to connect again?
I just cant seem to find this option anywhere in my routers configuration page.
I've replaced my old wireless router with a new DIV-655. Now, I can connect to my work's VPN and connect to servers and data via the VPN, but my Outlook client will NOT connect to the Exchange server.It (Outlook) just sits there saying "Trying to connect to Microsoft Exchange.Will it work.
View 3 Replies View Relatedi have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
View 3 Replies View RelatedDGL-4100
-> Wii
-> X360
-> PS3
-> DGS-2205 (gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522
We're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. Also, the DGL-4100 doesn't list it under the DHCP clients, but as I've got the DAP-1522 set to a static IP of 192.168.1.50.
DHCP enabled with default settings. Dynamic IP range from 192.168.0.100 - 192.168.0.199.Router shows laptop with 192.168.0.199 however when I check the IP on laptop I have 192.168.100.10 and both laptops are connected on my SSID with 90% signal strenght.
View 4 Replies View Relatedi have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
how to make the java SSH thin client applet bigger in SSL VPN Clientless portal?It works and all that but the window is literally half the size of the monitor and unworkable. You can't even hit tab! (tab moves focus around the browser...)I am using the latest java applet (Oct 2012) and ASA OS 8.4(5)
View 3 Replies View RelatedDo the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
I'm using WLC5508 /w 7.0..My client do not get its IP. Status shown "DHCP_REQD".I found in (Cisco Live) Troubleshooting Wireless LANs with Centralized Controllers This related with Enable/Disable DHCP Proxy checkbox. I solved. with Enabling this.But,
1) Why this box have been working correctly for longtime? No one did diable/enable this feature on my box.
2) I guest, ver7.0 Disables this chechbox by default. Or not? I also have others two 7.2 boxes. Those are all Enabled.
I need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies View RelatedI am using guest solution with two WLCs , one inside and one as anchor in DMZ.we have also NAC guest server to authenticate the guest users. inside WLC is 5508 and had been updated to latest version 7.2.103.0 last Thursday.
now we facing problem with the guest SSID , after the user authenticate, immediately disconnected and to access again he has to authenticate again and so on.
Is there any Bug with the new version because the setup was working fine before upgrading.
I have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedI have a WLC5508 , we are using external DHCP for WLANs
one WLAN is able to get IP from DHCP server but another WLAN not , the DHCP server is same , only 2 different scopes.
This is debug
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP received op BOOTREQUEST (1) (len 308,vlan 1, port 1, encap 0xec03)
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP processing DHCP
[Code].....
I have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies View Related