Cisco Wireless :: Connecting Two PLW400s To One PLE400
Dec 31, 2012
I just purchased two Linksys PLWK400 box sets — each contains one PLE400 and one PLW400. My intention was to set up one PLE400 by my router and then use the other two PLW400 to extend the wireless throughout my apartment (wifi is atrocious despite the apartment only being 1000sq feet).
All of the outlets are on the same circuit breaker and I can get the PLW400's to each work by themselves in different locations, but I can't get the network to recognize both of them at the same time. Once one is connected, the other is not recnognized (the Powerline LED never turns on).I am using the OSX "Cisco Powerline AV Utility" to set up WiFi passwords for each wireless unit. The Utility does not see the second PLW400 either.
I'm stuck and the documentation that came with the product (and available online) is so poor, there is no information about this usage — though individual product descriptions imply that it is possible.
View 2 Replies
ADVERTISEMENT
Apr 1, 2012
I connect to my corporate network using Cisco AnyConnect Secure Mobility Client. Once connected I can no longer print to my LAN attached printer and other local resources. I use the Cisco/Lyncsys E4200 router on my LAN and can re-connect to the storage on the local LAN by setting up Port Forwarding of port 21 and MS Windows FTP folder sharing. However, I can't seem to connect to a Terminal Services client by forwarding port 3389. Is there a way to connect to the local LAN after logging into the VPN connection. I can connect to regular HTTP/HTTPS sites and most other type of connectiins, just not my own local resources.
View 3 Replies
View Related
Jul 3, 2012
I have an AP already in lwap mode and I am unable to join it to a WLC. the WLC already has over 50 AP's attached and the license is ok. These are the messages I am getting.
*Jul 4 20:09:51.000: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 4 20:09:51.000: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 4 20:10:01.012: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[Code].....
View 3 Replies
View Related
Sep 13, 2012
I believe I know the answer to this question already but I just wanted to make sure. Is it possible to connect a LAP access point directly to WCS without using a WLC? WCS is just for management and reporting and does not act as a WLC.
View 2 Replies
View Related
Aug 22, 2011
how can i connect two different lans of ip addresses of head office in 192.168.10.series and branch 1 192.168.11.series, branch 2 in 192.168.12 series, branch 3 in 192.168.13. series. head office and the branches are connected with wireless
View 1 Replies
View Related
Jul 29, 2011
We just moved, and the family room (where the desktop is) had no coaxial outlet. The exterior box is at the other side of the house, and instead of wiring around our entire home, cable guy said we could easily set it up where the previous owners did (living room), and use a Netgear USB to make the desktop wireless.At Best Buy, I was told to buy Netgear N600 Wireless Dual Band USB Adapter WNDA3100 for $50. I install with the cd, and then plug in the USB as it suggests, and it just blinks from yellow to blue, not picking up my netgear wireless router in the other room. I go back to Best Buy, and they say that I need to buy another thing, now it's Netgear XET1001 85 Mbps Wall-Plugged Ethernet Adapter for another $70.Plugged one unit into the wall, and then plugged it into the Netgear Wireless Router. This will give me a solid light for Power LED and Ethernet LED, and then the middle, Powerline LED is a solid blue. With the second adapter, I plugged that in to my family room (with the desktop) and attached it also to my desktop with it's cord. This one has a solid light for the Power and Ethernet LED, but for the Powerline LED it's off. So it's not finding the other compatiable key, if I put it in between the wireless router, and my desktop (in the hall or kitchen) it will have all lights on, but I can't connect it with the cord to the desktop, and the USB does not pick it up any point.
Now, I can connect with my phone to the wireless network anywhere in my house, including the second floor. However, I can not, with or without the wireless adapters, connect with my laptop to the wireless network. I've done wireless with my laptop since I purchased it a few years ago, and while it can "see" the network, when I try to connect I get an error message that it's unable to join the network, and is now out of range, even when I'm sitting right in front of my modem/wireless router. It doesn't prompt for the password, I tried to manually add the password under network properties but it did the same error.I just don't know what to do or to try next, I don't know if I've set it up wrong, I followed the pictures in the manual, which is all it pretty much comes with, and did all the installation disks. Without it though I can't connect with my laptop, but my phones can..
View 1 Replies
View Related
Nov 10, 2011
I have had troubles connecting my PS3 to my Orange livebox. At first, I had the problem that it could not obtain the IP address so I manually entered it. This solved the problem. However, I also manually entered the Subnet Mask, Default Router (Gateway), Primary DNS and Secondary DNS. Now when connecting, it says I have a DNS error.(80710102)
View 1 Replies
View Related
Aug 25, 2011
How do i make my laptop wireless without having to have my laptop connect to all the wires?
View 9 Replies
View Related
Sep 22, 2011
I recently purchased a E1550 that works fine until I tried adding an external USB HDD for storage. The drive is a Western Digital 500MB drive I used to use for backups. Had no issues setting up the share and was able to access it just fine. But a few hours after hooking it up, my wireless devices could no longer connect and I could not access the admin page to see what was wrong. The E1550 was still pingable and my wired devices could still access sites through the router. Cycling power to the router did not work. What did get things working again was removing the USB drive (which killed all wired connections as well) and then cycling power. The E1550 was fine after that.
View 2 Replies
View Related
Sep 11, 2012
I have this doubt I can connect the antennas AIR-ANT2440NV-R= and AIR-ANT5160NP-R= in the access points 1262.
View 4 Replies
View Related
Feb 20, 2012
Having a bit of a strange issue with our Access Point at the moment. I recently set up a WAP4410N as our main WiFi hotspot using WPA2 encryption and it seemed to be working fine for all users, We had no issues when connecting Windows 7 laptops or windows phone 7 phones.However, we have a few people in our office that use HTC desire phones and while the phone will connect to the network it will not allow the user to browse the web or access any internet enabled features on their phone.The more puzzling thing is that a user with a HTC wildfire phone is able to connect to the hotspot without issue meaning it can't be a general Android issue.
View 9 Replies
View Related
Nov 7, 2012
I need a temporary additional broadband connection at home and I was thinking about a bt openzone hotspot connection...
I have a cisco 1242AG access point which can do bridge mode. The BT openzone thing requires a username and password. Is it possible to connect the 1242 in bridge mode to bt openzone?
View 7 Replies
View Related
May 29, 2013
I'm in the process of trying to get a used LAP1142N access point connected to my already established WLAN. We currently have 7 active LAP1142N, our controller is a AIR-WLC2112-K9, and I am only trying to add one additional access point. I say this access point is used because we purchased it used, given it's not out of the box and hasn't ever been active in my environment. So far what I've tried is initially connecting the access point on to my network (powered over Ethernet) and consoled in from my desktop. With this, I was able to see the previous configuration so I ran a write erase/ reload. The AP shows a solid green light, but doesn't receive any configuration from the controller even when plugged directly in to the controller (on ports 7 and 8). I'm new to wireless, but familiar with Cisco CLI and web interfaces. I can't necessarily tell if this AP is set to autonomous as opposed to lightweight, but that could be the problem. Otherwise I'm lost. I've attached text files with the boot from CLI and show run from CLI.Let me know any additional information you may need. End note, I'm recieving DHCP (you can tell from boot), but it's not the same subnet as my controller or other active access points.
View 5 Replies
View Related
Dec 11, 2012
I need to configure 3 Cisco Aironet 1131g for use. Normally we use the Cisco Aeronet 802 and once these are connected onto the switch, I can log on the WLC, find them and change the name and other settings. For some reason I cannot see the Cisco 113g on any of the WLC.
View 2 Replies
View Related
Jan 3, 2012
I am moving to a house in a fairly remote part of Australia without a telephone connection. To get the phone connected will be very expensive and take considerable time. I have mobile phone and wireless internet connection available but only with the most expensive provider. I am not a big user of the phone but every now and then, I have to make one of those calls that go through adozen menus and then leave you on hold for an hour, theb type of call that can send you bankrupt using a mobile service. My proposed solution is to have a prepaid wireless internet account, using a USB dongle connected to my computer as the internet connection. Then to connect either a SPA3102 or a PAP 2T between the computer and a handset and use a VOIP service such as Voipcheap to make calls. With this setup, I would have unlimited landline calls within Australia for around $50 per year, much less that something like Skype. Can I do this and if so, how? I have both devices and they are both presently configured to work connected to my Linksys gateway. Do I connect the computer to the LAN or eithernet of the SPA 3102 and will it just require a normal LAN cable? How do I assign the various addresses required? Do I need any extra software for my computer?
View 4 Replies
View Related
May 2, 2012
I am having problems connecting an 891w to a WLC, is it possible to have to separate vlans, one for the Lan ports and another for the AP module.
I do not want the AP part of the 891w in autonomous mode. The WAN port of the router will be connected to a DSL type service.
Is there a guide or something to get a 891W to connect to the WLC?
I would like to have users on a data vlan (vlan1) connecting to the network like a normal router, then the AP module to connect to the WLC via a different IP probably vlan 2
On the WLC itself i do not see any attempts in the logging.
View 10 Replies
View Related
May 27, 2012
I'm having a small issue using my external CIsco Wireless Card AIR-CB21-AG-E-K9 with a Lightweight Access Point 1552 (Outdoor) using 802.11a Radio.
Description of issue :
I can connect to a wireless network when i set the Wireless Mode to 2.4GHz 54 Mbps (802.11 g), and 2.4 GHz 11 Mbps (802.11 b) on the card but not with 5GHz 54 Mbps (802.11a).
Note that this card is compatible to 802.11 a, b and g.
All settings on the 2504 WLC is set to default regarding the radios configuration.
Both radio interfaces type (802.11 b/g/n and 802.11a/n) are operational and Admin status Enable on the WLC.
The status of the wireless card is as follows :
Profile Name - Wifi-Test
Link Status - Not associated
Wirless Mode : 5 GHz 54 Mbps
Network Type : Infrastructure
Current Channel : Scanning
View 3 Replies
View Related
Jan 18, 2012
I have an ipad that is not able to connect to a 1142 Autonomous AP. This AP was originally a light weight AP and then downgraded to autonomous.A strange thing i see is that the AP shows me only two radios. 802.11 N(2.4 GHZ) and 802.11 N(5 GHZ). I suspected the AP not to support the b/g networks. i then downloaded the most recent software but i still cannot get it to connect and on the AP's GUI i only see the above two mentionned radios. i tried to connect to two SSID's. one using WPA2 and another with open authentication and no security.but this does not work. Is it possible that some 1142 do not support b/g networks?
View 21 Replies
View Related
Nov 28, 2007
I am trying to get a controller to work on my network. output from the switch arp table.
Internet 172.28.227.2 0 001b.d5cf.79c0 ARPA Vlan103
Internet 172.28.227.1 - 001c.b1ad.7400 ARPA Vlan103
Internet 172.28.227.12 0 001d.a1cc.b7f8 ARPA Vlan103
controller config:
Interface Name................................... management
MAC Address...................................... 00:07:0e:25:ac:a0
IP Address....................................... 172.28.227.2
IP Netmask....................................... 255.255.255.0
[code]....
The switch see's it but i can not ping or access it via web or telnet.
View 5 Replies
View Related
Feb 13, 2013
I just picked up a WET200... connect it wirelessly to a Verizon Mifi so wired devices can get access to the Internet.
I've had zero luck connecting the WET200 to a wireless network...I've tried two different ones and I've also tried changing from WPA to WPA2.
View 1 Replies
View Related
Oct 28, 2012
I have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:
[code]....
View 8 Replies
View Related
Mar 25, 2013
I have successfully setup the Cisco 2504 (AIR-CT2504-K9).
Trying to add 2 Access Points (AIR-SAP1602I-A-K9). I created static IPs for both in the router (RV180). The Access Points are connected to the PoE ports on the Cisco Switch (SG200-08P). The 2504 is connect to one of the non-PoE ports on the SG200. The SG200 is then connected to another switch (SF302-8P), which is connected to the Router (RV180), which is connected to the cable modem (Cisco DCM3000).
I am able to ping both of the access points from within the LAN, but they do not show-up on the 2504 console.
View 3 Replies
View Related
Aug 30, 2011
I have the Linksys E3000 High Performance Wireless N-Router and I am having trouble connecting it to my PS3. The PS3 recoginizes the router and gets as far as trying to connect and then it tells me that the internet connection has failed and that the connection has timed out, even though it only tries to connect for a couple of seconds, therefore I dont see how it would have time to time out.
View 2 Replies
View Related
Sep 14, 2011
So I just got a wireless presentation gateway wpg 120 to connect to projector wirelessly. For me to connect to the projector i need to set wireless network to its wireless connection. But if I connect to wpg 120's connection, there is no internet access.Is there any way I can connect to two wireless network or use wpg 120 to connect to internet using it's connection.
View 3 Replies
View Related
Jul 30, 2012
My internet was running perfectly fine for the first 6-9 months, but recently has deteriorated to a mess (keeps getting booted on and off or slows to the point where it's virtually unusable). It seems to be the worst on weeknights and weekends.<removed by moderator - etaf>, For reference, I am running a Windows 7 machine, connecting wirelessly through a Netgear WNR1000 router. When connected to the router using an ethernet cable, it works perfectly fine. There is another wired device which works fine, so it's mainly the wifi connection. For my Windows 7 PC, the wireless cuts in and out (working fine now), and oftentimes drops me. I have to reset the router/modem multiple times just to be able to use it. My roommate who also has a wireless PC also has problems connecting wirelessly as well. Currently, I have IPV4 connectivity, but no IPV6 connectivity.
My ipconfig below:
Windows IP Configuration
Host Name . . . . . . . . . . . . : J-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Peer-Peer
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 14 Replies
View Related
Jul 21, 2011
I have a wireless modem. Its main connections are power, and phone line. Since its a wireless modem it is not connected to my PC through wire. i have a Data card USB which is plugged in my PC. The wireless modem senses this Data card and my internet was working normally. I live in New-Zealand and I was having a Telstra Clear connection with their modem and Data card. Since it was acquired by Telecom, the internet provider had given me this new wireless modem but the Data card remains the same.Now this new wireless modem is not connecting. But the laptops are getting connected through WiFi. Since my PC has no WiFi, it uses this data card. My PC is not getting connected to the internet. I tried plugging in the USB Data card in and out, updating the drivers and stuff.I want my PC to get connected to the internet.
View 3 Replies
View Related
Jun 25, 2012
This is a problem i had after i reinstalled windows vista on my laptop. I recently reinstalled windows vista onto a laptop. The laptop is unable to find the router. I checked the drivers, and i am not sure if im missing any. There is a yellow mark on my network controller, but there is no description or details for it. The internet works while connected to an etherent cable directly to my router. I went to the manufacture website (dell), and downloaded/updated the drivers. I ran PC diagnostics and the wireless still doesn't work.
[code]....
View 4 Replies
View Related
Feb 19, 2011
when trying to connect it says nodhcpdiscover received sleeping
View 1 Replies
View Related
Jun 9, 2011
I cannot get my USB N adapter to connect with a u-verse G router
View 4 Replies
View Related
Jan 24, 2013
I have a netgear router. I have my kindle, 2 laptops, and a net book that are on the network. I bought my husband a "new" laptop. It will not accept the password in alphabet form.
View 1 Replies
View Related
Sep 10, 2011
I just got a linksys wireless adapter for my pc, but the cd drive won't read the setup disc. Is there a way to hook the laptop to the pc and load the program?
View 4 Replies
View Related
Feb 9, 2012
How do i make my wireless router connect to another wireless router?
View 1 Replies
View Related
Nov 18, 2011
How can i stop others from connecting to my router
View 2 Replies
View Related
