Cisco Wireless :: WLC 5508 Licenses Disappear

Jul 5, 2011

After install the License for 25 AP more to a wlc 5508 with 100 AP base license  and reboot WLC, the License base for 100 AP´s and this new one 25+, it's not anymore on the system, after reboot the WLC show 0 AP´s supported, and the only one license appear are 500 AP evaluation with Time expires.

View 1 Replies


ADVERTISEMENT

Cisco Wireless :: 5508 HA Pair Licenses

Apr 17, 2013

I have 2 5508 that are currently running as active with 150 licenses each. I want to go to HA SSO can 100 of the licenses be relicensed to the primary since it only requires 50 licenses to convert an active license 5508 to standby HA SSO?

View 3 Replies View Related

Cisco Wireless :: 5508 - Licenses Require Any Modification When Flashing?

Mar 13, 2011

We have a cisco services contract with IBM that supplies us access to the usb drivers, firmwares etc, and we have a Cisco 5508 6.x running ~30 Cisco 1252's, some 1231's and (potentially) some 1262's once the firmware update is done.
 
We have a base-count license(permanent) of 50AP's, no expiry
 
So I guess my questions are:
 
1) When flashing the new firmware - do the licenses require any sort of modification, or will they work as per normal

2) Are any serial numbers or codes required to be entered once the 7.0.98 firmware is installed?

3) I assume that the old firmware/config becomes 2nd in line to the primary boot option of the firmware during boot process?

View 6 Replies View Related

D-Link DIR-655 :: Wireless Network Disappear?

Feb 14, 2012

My internet speed was very slow so I re-set up my wireless network again. After re-setting up, my wireless network always disappears when all my wireless computer/phone get off the network for several seconds. When I try to get my wireless connection again, none of my devices can detect it. In addition, the light of the wireless sign on my router is constantly on (blue), but no device can detect the it. I always have to go to my wireless set up and save my setting again (no change to the current setting). What can I do to fix my wireless network, so it will be detectable at all times?

View 7 Replies View Related

D-Link DIR-655 :: Wireless Signal Disappear Constantly?

Dec 13, 2011

just bought the DIr655 two weeks, everthing was fine except the wireless.almost every day around 6pm the wireless signal are disappear but the internet connection was fine with Lan, and  i have to reboot the rounter inorder to get the signal back.  i tried update the firmware but it it newest firmware on my rounter.

View 11 Replies View Related

Wireless :: Access Point Disappear From Neighbor After Two Minutes

Jun 26, 2011

i have switch 2960 POE connected to access point WiFi Cisco when we connect the AP you can see it in the neighbor after 2 minute all AP disappear?

View 1 Replies View Related

D-Link DIR-655 :: Wireless Signal Will Suddenly And Randomly Disappear From Laptop

Dec 14, 2011

I have a dir-655 xtreme N gigabit router with 2.03NA version firmware. The wireless signal will suddenly and randomly disappear from my laptop. I checked the properties of the network connected it remains on the same channel when it reconnects so I figure it's not a channel issue.I have reviewed this forum for hours and have made many changes to my settings, but nothing seems to keep the wireless signal from stopping.

Computer: dell inspiron 6400
OS: windows XP pro (sp3)
ISP service: DSL
Modem: stand alone (Sagemcom 4300)
Router: dlink / xtremeN gigabit router / dir655
Set for mixed g, n and b  wireless mode
Security: wpa-personnal / TKIP
Firmware: version 2.03NA

View 14 Replies View Related

Linksys Wireless Router :: Couldn't Connect To EA4500 - Network Disappear From List?

Jun 24, 2012

I've recently purchased a Linksys EA4500 router. I've got home, I've used the installation guide CD thingy, connected 3 of my laptops wirelessly, no issue there.However when I tried to connect my 4th laptop problems came along. The problem I was dealing with was that I couldn't connect to the router. I mean I could see the network name appearing in the list, but when I tried to connect the network would just dissapear from the list, not connect, and wouldn't back on the list unless I've reset the laptop. Anyhow I've ignored that computer because I thought it was two years old and it might have had a wireless network adaptor issue, although it was conneting with no problem to my former router D-Link DIR 365.Anyway, just yesterday I've purchesed a brand new netbook (Evolio U9) and it doesn't see my router, although it sees all the other connection availables (my neighbors' wirless networks), I even connected to one of them just to test if anything was wrong with the netbook.
 
I also have problems when trying to connect with an Iphone 4. Well, it does connect, but the connection to the iphone just goes on and off making it impossible to use. It's really strange that all the 3 Iphones in my home have no issue connecting, not even my Glaxy S3, nor any of the Smart Tvs, nor the printer.Does the router have any number of limited connections available? The router configuration is the ones done from the CD. I've only assign a SSID and a WPA password.Please note that all the computers above are GENIUNE Windows

View 9 Replies View Related

Cisco Wireless :: Difference In Licenses On Prime Infra 1.2?

Jan 13, 2013

difference between License types on Cisco Prime Infra 1.2 as below
 
Base License
Lifecycle management License
compliance management license
Automated deployment Gateway
Assurance Management License.

View 4 Replies View Related

Cisco Wireless :: Context Aware Licenses Difference For MSE 3310?

Mar 11, 2012

I am getting a hard time in order to understand the real difference between the two types of context aware licenses for the MSE:
 
1 . AIR-CAS-1KC-K9 -  Context Aware License For 1K Clients and Tags (RSSI based)
2. AIR-CAS-1KT-K9 -  Context Aware License For 1K Tags(RSSI, Chokeponts and TDOA)
 
For a regular network without any devices with tags such as RFID, I understand I do not need to get the .2, only .1, even though the .1 also is shared with clients at 1K of each. Also, the .2 does not say clients, only tags and advanced features as TDOA. Going through the Q&A it does not clearly says the difference, when to use one or the other.

View 3 Replies View Related

Network Computers Disappear

Aug 4, 2011

I have a vista, an xp, and a win7 computer networked. The xp is very temperamnetal, in that it randomly is accessible and just as randomly disappears. i often get the message "Computer (name) is not assessible...." The trouble is most acute in trying to access the xp machine from the win7.

View 4 Replies View Related

Cisco :: Prime LMS 4.2.1 Archived Configurations Disappear

Sep 13, 2012

We upgraded to Cisco LMS 4.2.1 recently and we have noticed that every time we reboot our Windows VM Server the archived configurations from the network devices are no longer displayed. They do not appear in the archive, version tree or directory. We are meeting the minimum system requirements for running LMS 4.2.1 and we do not seem to have found any possible bugs related to this.

View 8 Replies View Related

Cisco Switches :: SG 200-08 - Configuration Changes Disappear On Power Cycling?

Sep 17, 2011

the only change that survived power cycling is the change of default password that it forced me to do.

View 2 Replies View Related

Free Dlink Ap Disappear From List Of Available Wifi

Feb 18, 2013

I got a wireless HP all-in-one PC and was able to connect to the Internet via the free Dlink wi-fi access point. Dlink no longer appears in the list of available networks. The network adapters are fine. I'm running Windows 7.

View 3 Replies View Related

Vista Mapped Drives Disappear After Reboot

Jun 6, 2011

I have a network with a Western Digital NAS. Several computers are on the network, some connected via ethernet cable and some via wireless. The NAS has several shares that are password protected so that only certain users can map to them - each PC has its own private share used for backup.

The problem device is a Fujitsu Seimens Amilo laptop with Vista as the OS. When trying to display a map of the full network it is unable to display one - I have tried all of the solutions described by the Vista help but none of them work.When using Map Network Drive and trying to browse for the NAS, nothing is seen - the only computer showing on the network is the Vista laptop. If I type in the share name using \nas_nameshare_name it won't connect but if I use the IP address, such as \192.168.0.101share_name, then it does connect. I enter the password, select Reconnect at logon and the drive is mapped.

If I put the laptop to sleep the drive is still mapped when it wakes. The drive remains mapped for as long as the laptop is on but if I reboot it then the drive is lost. In fact, there are two mapped drives, one with a password and one without. After a reboot the drive with the password is still showing, but as a disconnected drive (double clicking brings up the password entry screen, and then the drive will be mapped). The drive without the password just isn't there at all.

View 9 Replies View Related

Folders Disappear From View On Networked AV Player?

Aug 27, 2012

here is my set-up.

(upstairs)
Windows 7 64 bit pc (2year old),
Netgear DGN2000 wireless modem/router,
Seagate GoFlex Home NAS drive,
D Link Powerline AV Network Kit,

(downstairs)
D Link Powerline AV Network Kit,
Yamaha RX-V671 AV Amp,
Panasonic TX-P42V20B TV,
TP-Link 5-port 10/100Mbps Desktop switch,

From the first time I set this up I have had problems in seeing all the folders I put onto the NAS drive for streaming to my TV and AV amp.Half of my music folders From the letter K upwards simply disappear from the menu view on my amp after I switch it off then back on the next time I want to listen to it. When I check the NAS drive on my PC, all the folders are still there but are not accessable downstairs on the amp.I can re-transfer the "missing" folders and it's fine till I next switch off and on again and its always from the same point that the folders are missing.The TV is also suffering from the same problems when I want to view photos and videos which are present in the drive upstairs but not visible on the menu on the TV (all missing on the TV!)Everything is connected with cat6 leads and I can stream internet radio (which is built into the amp) without any problems so it seems to me to be a communication problem between upstairs and downstairs.My house wiring has all the sockets on one ring main so that should be ok but I wondered if the router was not up to it with it not being a gigabit router.

View 4 Replies View Related

LinkSys WRT54G Router - Available Network Disappear In Windows 7

Jun 16, 2011

I have a Sony Vaio laptop which has an Atheros AR9285 wireless network adapter. My router is LinkSys WRT54G. I have configured this router with an SSID and encrypted using WEP.I created a network using 192.168.1.1, saved the configuration and then exited out.This creates a network that Windows "sees" in the list of available networks. However, for reasons I cannot figure out when I shut off my Vaio (I thought it happened when I powered down my router) why my available network does not "see" the network I just created.Under "manage wireless networks" I can see my network, but on the list of available networks it is not there. I then reconfigure the router and the network shows up. I at first thought it was a router configuration problem, but it now appears to happen when I shut off the PC - almost like I am not saving my configuration somewhere

View 10 Replies View Related

D-link Dir-655 :: Losing Wifi Ap / Just Disappear From Ssid Scan

Jun 10, 2011

I have a dir-655 Firmware Version 2.00, hardware:B1 It's a new wireless router and it's just a week ago I got it.My problem is that the wireless is just stopping to work, it just disappear.When I do a rescan of wireless AP's the ssid and my AP is not showing up.I have to reboot the router the hard way by unplugging the power source.I have multiple computers and wireless devices, and they all loose connection and no one even see the ssid (AP) defined on my dir-655.It's connected to a cable modem switch (without nat), I'm running dhcmp on my router. No Qos engine is enabled.This happens when I'm working from home with a VPN tunnel from my pc to my companies network.I've tried to make a ticket on this on dlink support pages, but their support system only works on IE7, and the password is anyway rejected. how to solve the termination of my wifi ap?

View 9 Replies View Related

Icons Of Files Mapped To Network Drive Disappear From Desktop

Nov 25, 2011

I got a strange incident happening to my work computer. Whenever i step away from my desk and come back only to find Icons of files mapped to other network drives other than my local drive have disappeared from desktop. I have to restart my computer to get these back. It only happens when i have walked away from my PC and I have verified that no one has sat at my desk to use my computer while I'm away. The other PC are also networked to the same servers as mine and theirs are not affected at all.

View 1 Replies View Related

Network Printers Disappear After Logoff - Logon To Terminal Server?

Feb 8, 2012

I have an annoying problem with networked printers disconnecting/disappearing when TS users logoff. Current configuration is: SQL server (WinSvr 2K8 R2 Std) has printers installed on it (standard TCP/IP Port) and printer is shared, there are also some printers installed on the DNS server and a couple of satellite offices. Users connect to TS servers (WinSvr 2K8 R2 & WinSvr 2K3) printers are connected and work fine until they logoff, when they log on the printers are gone "sometimes some printers are still there!?" I have tried logging onto the server as domain administrator and connecting printers but they won't even stay for administrator (have had this with win7 client machines) and tried directly 'console' at the server. I have looked at the printers on the SQL server and sharing properties, it is stoping printers from coming back at login on TS Note that local (client machines) connecting to the same shared printer from the SQL server don�t have the problem it's just on the TS server.

View 2 Replies View Related

Cisco VPN :: 2 Licenses On ASA 5520?

Aug 19, 2012

Ive got a customer asking for 2 products to be installed on an ASA 5520?
 
ASA 5500 SSL VPN 10 Premium User License and AnyConnect Essentials VPN License - ASA 5520 (750 Users)?
 
Am i correct in saying only one of those licences will actually be active at any time?

View 3 Replies View Related

Cisco VPN :: ASA 5520 - Add 50 More Licenses?

Feb 4, 2013

We have a 5520 ASA with a 100 user ssl license. We need to increase this but 250 is overkill. Is there an option to just add 50 more licenses or do we have to go up to 250?

View 2 Replies View Related

Cisco VPN :: ASA 5520 - Number Of Licenses That Are Available?

Mar 6, 2011

Need to know the number of VPN licenses that is available,

1)  I have site to site vpn connections.
2) SSL VPn (browser)
3) IPsec  client vpn.

How many vpn connections are allowed? can multiple connections be made using the same username for IPsec VPn clients.?

View 2 Replies View Related

Cisco WAN :: Licenses Lost After Power Off With IOS XR 4.0.1?

Feb 15, 2011

Any trouble with IOS XR licenses dissapearing after a power off ?I was able to add them correctly, but after the power off "show licenses" gives and empty message, but the logs states the licenses are already there.I'm working with a CRS-3 with IOS XR version 4.0.1.

View 1 Replies View Related

Cisco WAN :: ASR1001 Licenses Information Required

Jan 29, 2011

We are looking at buying an ASR1001 but I'm confused by the Licenses and I've struggled to find the information in the cisco data sheets. The router will need to run IPSEC on gre tunnels and I figure that I need the IPSEC license (FLSASR1-IPSEC) do I also require the Advanced IP Services license? or is all that is required the IPSEC license? Is there some sort of list that shows the feature set of each license, they cost the same amount so I'm not sure which license fits what we require best or if we need both.

View 1 Replies View Related

Cisco VPN :: Increase Of SSL VPN User Licenses On ASA5510?

Nov 9, 2011

is that possible to increase the number of SSL VPN User Licenses on ASA5510-SSL100-K9 using for example L-ASA-SSL-50= ?Is there any limitation ?

View 3 Replies View Related

Cisco VPN :: 5505 Upgrade Only Web Vpn Portion To Allow More Licenses

Sep 16, 2012

I have a cisco ASA5505, with  base license, it appears I can only have 2  ssl/webvpn connection running at any one time.  How can I upgrade only the webvpn portion to allow more licenses? 

View 2 Replies View Related

Cisco VPN :: AnyConnect Premium Licenses On ASA5540?

Oct 21, 2012

i currently have a ASA5540 with 250 SSL VPN Premium licenses and looking to purchase another 500 licenes on top of what i already have.I have been told that i cant simply add 500 licenses onto the 250 to make 750 in total and that i need to purchase a 250-500 licenses or 250-1K licenses. Is this correct? I ask this because on the cisco website, that there is L-ASA-SSL-250-500= & L-ASA-SSL-500-750= part numbers?

View 1 Replies View Related

Cisco :: WCS Not Showing In 7.0.230.0 WLCs In Licenses Center

Apr 22, 2012

We've been upgrading our WLCs to 7.0.230.0 but I've notifced after they have been upgraded they no longer appear in the controller section in License Center on the WCS. They still exist in the WCS and the audit the configuration jobs are working. I've also tried manually triggering the Controller License Status background tasks and this runs without reporting any errors.I thought it may be because the WCS was at a lower version but I've now upgraded this to 7.0.230.0 also but the WLCs are still missing.

View 1 Replies View Related

Cisco VPN :: 5550 IP Phone SSL VPN - Licenses Required

Jun 6, 2013

How to confirm the linceses required for me to get this working. I understand that it needs the 'AnyConnect for Cisco VPN Phone' license but do I also need to have anyconnec essentials? This is for ASA version 8.2 and the a license info below is for the ASA i intend to delpoy this on. This platform has an ASA 5550 VPN Premium license.

View 2 Replies View Related

Cisco Firewall :: 5585 - ASA Shared Licenses With 8.3?

May 2, 2011

Shared licensing of ASA?I have 2 ASA 5585 in cluster and I have to Implement SSL / VPN license  My question:Since I have a cluster in 8.3 version, can I use only one license VPN / SSL for two, without necessarily implement the Shared Server licenses and participant.

View 4 Replies View Related

Cisco VPN :: 5520 - Error When Trying To Redeem L-ASA-SSL-100 Licenses

Jan 29, 2012

We are trying to activate two L-ASA-SSL-100= licenses in our ASA5520 and we are getting the below error:

Wrong Sku(s) 'L-ASA-SSL-100=' for 'ASA5520_AIP20-K9' : Device contains following licenses 'ASA5520-VPN-PL,ASA5520-SSL-50, ASA-AC-M-5520, ASA5500-ENCR-K9'
Serial Number = XXXXXXX

The new serial number provided is not the same platform type as the failed serial number. An upgrade request is not allowed.

View 1 Replies View Related

Cisco WAN :: Nexus 7000 Missing Licenses Which Should Come In Bundle

May 8, 2012

We have ordered the following 10 line items , but only got 3 licenses , unless the 3 licenses somehow have all the licenses integrated into the 3 part numbers below, but I suspect not.
  
Licenses attached from Cisco:-
 
N7K-C7009-XL-SBUN   Nexus 7009 Scalable Feature License                         x  1
N7K-C7009-SBUN-P1   Inc LAN,ADV,TRS,EL2,DCNM,DCNMSAN,MPLS,SAN,XL -Promotion     x 1

[Code].....

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved