Cisco Wireless :: WLC 5508 Can't Communicate To Wireless Device
Aug 8, 2012
i have a wlc 5508 with code 7.0.220, with multicast enabled in it and on the lan too.I am having a bit of confusion getting bonjour to work on the wireless side. Looking at some of the cisco docs, i still have some questions on how to get it working in my specific enviroment.
I have the wlc conected to the lan via a port-channel. 2 wlan (ssid1 and ssid2) each wlan maps to a specific vlan (dynamic int), the management int (also used for dynamic ap-manager) on a third vlan (vlan x).
I need to get Bonjour working between ssid1 and vlan-x, so my wireless clients (in ssid1 can use bonjour with their laptops) can synch between wireless and wired. I know that you can do this within the same wlan (ssid) but in this case, when a user has a laptop wired into the network he cant comunicate to the wireless device. I read about Vlan Select and Multicast Optimization however, from what i understand i need to setup an interface group and just assign my wlan1 and management int to it, correct?
when or if i need a different segment (vlan y) in my lan to also "bonjour" with ssid1? For this i assume i would need to create a dynamic interface on the wlc using the same IP segment and do the a new interface group?
View 5 Replies
ADVERTISEMENT
Jun 4, 2013
I am deploying Cisco 5508 with Cisco 1602 Access Points at one of my client's office. User authentication will be done through Microsoft IAS Server working as RADIUS Server. There is a requirement from my client is that the user over wireless can only be able to login to One device using its user ID. I want to inquire if this can be done through WLC or it can be restricted on the RADIUS server? Looking forward for comments.
View 4 Replies
View Related
Jul 9, 2012
I have installed ANM 5.2 virtual appliance.I have an issue importing a Catalyst 6500 device.When I try to import it, I get the following error: Device discovery failed: Cannot communicate to the device.Authentication failure while attempting to connect. Verify the device type and credentials. I double verified and the credentials are correct.I user SSH version 2.I use the following special carachters in the password: "!" and space.I don't use enable password to connect to the 6500 device. The 6500 device has a privilege 15 username.In ANM, the enable password is a requirement so I just fill in the regular password.I think the issue is appearing due to one of the following:
1.) The ANM does not support the special carachters I use in the 6500 password.
2.) Then ANM requires enable password, while I don't use enable password in the 6500 switch.
The 6500 runs SXI6 software version.I can't configure an enable password or configure a test username without special carachters beacause it's against the organization's policy.
View 1 Replies
View Related
Feb 22, 2012
Windows cant communicate with the device or resource(primary dns server). The device or resource is not responding to requests.
View 4 Replies
View Related
Aug 7, 2012
I have had clearwire for a few years, about 2 months ago the internet started being weird. It would go slow, only load part of a page or disconnect completely. Now I cant get on at all. Not with my HP laptop, not with my daughters iPad, my husbands HP, ipod and not even if I hook up directly to the router. I have gone through 3 modems and 2 routers trying to fix this, but nothing has changed. When I run a trouble shooter, under "Problems Found", it says, "Windows cannot communicate with the device or resource. (primary DNS server)" I am currently on my computer at another location, every device we have, can get on the internet at other locations.
View 1 Replies
View Related
Jan 3, 2012
I am trying to set up my computer with my old connection. I use my laptop (acer aspire 5742ZG) and before I moved out it worked like it should have. Then while in the other town I needed to set up my connection, this time by myself (through some sort of interface in 192.168.1.1). Now that I'm back next thing happens: I appear to be online, I am online on skype (can chat, and people chat back) but when it comes to connecting to the internet through the browser or an online game I play it's not responding, as if there is a problem.I use windows 7, so the troubleshooting software reports what's in the title.The problem is not with the connection - 3 computers are connected to it, 2 with cable, 1 wireless. I would use wireless too, but I am too far away from the modem (it's in another house, and I have a long cable which works, posting from the desktop computer connected to it). [Code]
View 8 Replies
View Related
Jan 16, 2013
I have a ASUS NB K52f/k62f series, 3GBRAM intl Pentium CPU2.13GHz 500GB HD 392GB free, windows 7 home premium 64bit. wireless network connection: Atheros AR9285 Wireless Network Adapter
I am able to connect to the internet via Ethernet but I cannot connect via wifi. Its been work fine for 3years now but now its not able to connect to any network and all my other devices are able to connect just fine to these networks fine. The error message I get is Windows can't communicate with the device or resource (primary DNS server). so far I have disable and re enabled the wireless connection, reset the TCP/IP, went through properties of ipv4 and 6 and set them to obtain an ip address automatically, and system restore from when I was able to connect via wifi still not luck
View 14 Replies
View Related
Oct 9, 2011
Problems have arisen since purchasing a new laptop with Windows 7. The problem seems erratic. The laptop connects to file servers on the network, but often cannot connect to the network. If it connects, often connection is lost when clicking to a new page.Usual error message: "Windows can't communicate with the device or resource (primary DNS server)"Network map shows communication lost between ADSL and network.Direct Hard wire connection to internet through ADSL works without issue. Hardwire connection through DIR-655 same as wireless: erratic, error messages. This message posted from another wireless router, specifics not known, connected without issue, on-line for 3 hours without problems.
-IP address: no difference between using automatically obtained or assigned IP address
-DNS server: no difference between using automatically obtained or assigned IP address
Router setup numerous times using CD ROM set up program.Firmware updated to the most recent version.Gone to tech support several times; can get the PC to connect and once done, tech support says its working only to disconnect within a few minutes.What must I do to get this DIR-655 router working on a regular basis?
View 7 Replies
View Related
Jul 15, 2012
I have been asked to allow our employees to connect their own devices to a open wireless network. I want to control access to preauthorized devices and I am looking for solutions. We do to have access to any other control devices like an ACS and I would like to archive the result using just the 5508 controller.
View 1 Replies
View Related
May 30, 2013
I am using ISE 1.1.1.268 and WLC 7.2.111.3 and NAC agent version 4.9.1.6 on Windows 7 Client machines.
About once a day i get the error "ISE Alarm (WARNING): Dynamic Authorization Failed for Device".
The device it is referring to is my NAD, a WLC 5508 running 7.2.111.3
I have looked at the logs and I cannot see anything in the logs which corresponds to this message so that I can troubleshoot further. Maybe I can if I am enabling the correct logging level on the correct ISE component.
What are the components and the logging level that I should set to get some more detail about this error?
At the moment, I have only set debug logging on Active Directory. I have TRACE logging set on Posture, Run time AAA & prrt-JNI.
I do not want to enable too much debug logs, so what is the specific element that I should be debugging.
I thought debugging the posture element would be enough but when I look at the logs there is nothing there that relates to this message.
View 3 Replies
View Related
Feb 17, 2011
Wireless on this laptop will not connect. Another laptop connects without problems.DDS (Ver_10-12-12.01) - NTFSx86
Run by Owner at 20:48:45.56 on Fri 02/11/2011
[Code].....
View 2 Replies
View Related
Jan 25, 2013
I need to configure LAP1522 series Lightweight AP. When I connect my LAP to switch port .It pull out IP address from DHCP.I configured DHCP option 43 on that subnet.All Other lightweigh APs are working fine.When I ping that Ip address from the switch where I configured LAP it just give 100% loss.Also MAC-Address on that port show me two mac-address entry from that port. [code]
View 3 Replies
View Related
Sep 19, 2011
One of our laptops won't connect to the internet via wireless, gives a "Cannot communicate with Primary DNS Server (192.168.1.20)" error. It works fine when plugged in via ethernet, and all our other computers connect to wireless just fine.
The wireless is set to acquire DNS automatically in the TCP/IP IPv4 properties. I've tried to flush DNS, reset IPv4 and reset Winsock with no luck.
[code]....
View 3 Replies
View Related
Sep 25, 2011
i keep getting an error message when i scan. error message: cannot communicate with scanner for these reasons
-scanner is turned off
-scanner is disconnected (it is disconnected from LAN, if using on LAN)BUT MY MACHINE IS ON
View 3 Replies
View Related
May 7, 2011
I have 2 brand new systems, a desktop running Windows 7 Pro connected with a had line, and a laptop running Windows 7 Home Premium connected wirelessly. Both can access the router, both can access the internet, both can be pinged from the router. However, they absolutely cannot see each other on the network. If I try to ping by name, the addresses don't resolve. If I try to ping by IP, I get either no reply or the "destination host unreachable."I've disabled firewall completely on both. I've double, triple, quadruple checked all sharing settings (network discovery is enabled on both, sharing enabled everywhere, etc. etc.). I've tried disabling all other network adapters on the laptop, no difference. I've tried all of the online tips about repairing winsock.
View 8 Replies
View Related
Mar 22, 2011
E4200 does not allow homegroup to communicate
View 9 Replies
View Related
Jan 28, 2011
I've set up my HP on a network with two laptop pc's. The second PC works great but the first PC will not let me print a document from a program. I get an "unable to communicate with Printer" Error. However, I can scan to both computers and the first computer can print a diagnostic page.
View 2 Replies
View Related
Aug 12, 2008
wrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.
View 9 Replies
View Related
Sep 22, 2011
Does this device support Wireless Wake On LAN and if so, what does one need to do in Windows 7 to enable this function?
View 9 Replies
View Related
Nov 7, 2012
I have a WUSB11 Wireless B and wonder if it accepts WPA2 security, I originally had my router set to WPA, and the wireless B worked fine, I have since changed to WPA2 and notice the Wireless B device won't connect.
View 8 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
Oct 24, 2011
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Apr 7, 2013
Is there any way to configure a wired guest network with a combination of 5508 and 2504 wireless controllers? I am aware that the 2504 does not have wired guest functionality, however is it possible to set up a wired guest on the 5508 and using mobility anchors, transmit the l2 information through eoip to communicate with the remote vlan?Home built NAC solution, using 802.1x authentication on switchports for public areas. If user is an employee, communicates with the supplicant on their machine, and places them on an internal vlan.If user is a guest, user fails 802.1x check and is placed on a "guest" vlan with an ACL and external DNS.If placed on the guest vlan, the user has to accept a terms of use form.This is working currently with our 5508s without any issue, however we have some remote offices we'd like to roll this out to that are using 2504 controllers. I'm hoping there's a way that I can use the 5508 as an anchor or vice versa to make this work.
View 1 Replies
View Related
Apr 15, 2012
Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies
View Related
Aug 1, 2012
I want to install a pair of 5508 to manage the whole wireless solution and I have a few questions regarding deployment, Please refer to the topology. The management and ap manager interfaces are conifgured with the same ip address range and thus the same vlan which is 10.160.254.X/24 also all the APs(1,2,3) in that building have the same IP address range for management which will be manually conifgured. The AP's (4 and 5) on the other building have another range of IP address for management and here is the first question. Will the AP's 4 and 5 join the WLC if I manually configure them to point to it? I know I can group interfaces and use them with the same SSID BUT the WLAN vlan in both sides are different and are separated by a router and hence the next question: Can this be done even if they are separated? and if I can, how is this possible, should I configure a dynamic interface in the WLC with an IP of that network even if it doesn't exists on that side? I'm kind of confused with this.
View 5 Replies
View Related
Jul 30, 2012
I have a Cisco 5508 setup at a host site with 3 other sites connected using hreap on 1252APs. When doing testing of network speed I find that the throughput from the wireless to wired network is at about 18mbps yet the same test on wired side is 85-100mbps and wireless to wireless is 18mbps
View 4 Replies
View Related
Oct 2, 2011
I am running 5508 controller with version 7.0 and 1142N access points.. I am facing a problem on user connectivity.
Wireless Users are getting frequent connection and disconnection. These users are not getting connected to the access point nearby although this access point is up and running. I have tried reducing the power level, configured the AP after resetting it.
View 2 Replies
View Related
Apr 19, 2012
I'm trying to share my internet connection to another PC via wireless device.Which technique can i use for it.Topo:-Internet <-> PC(A) <--> WD (B) <--> WD (C) <--> PC(D)PC = Windows XP (OS)WD = Wireless device Access Point / BridgeIn the above topology, i need to share my internet connection from (A) PC to (B) PC through wireless device, I have plan to establish the internet sharing between two PC, In which mode Access Point/ Bridge mode is adequate for this wireless device to make connection and internet sharing between the PC
View 5 Replies
View Related
Apr 24, 2012
we have a working wireless network managed by a 5508 WLC and nearly a hundred AP in different buildings. We want to integrate several apple-tv in different WLAN. We enable global multicast mode and igmp snooping on the WLC. When clients connect to these wlan airplay functionnality operates for 2 or 3 minutes max and after the airplay icon disappears on iDevices. If i want airplay to work again i need to reboot the Apple-TV but again it can't work for more than 2-3 minutes.
View 8 Replies
View Related
Mar 7, 2012
I am using guest solution with two WLCs , one inside and one as anchor in DMZ.we have also NAC guest server to authenticate the guest users. inside WLC is 5508 and had been updated to latest version 7.2.103.0 last Thursday.
now we facing problem with the guest SSID , after the user authenticate, immediately disconnected and to access again he has to authenticate again and so on.
Is there any Bug with the new version because the setup was working fine before upgrading.
View 1 Replies
View Related
Apr 17, 2012
I have a new wireless configuration on a 5508 WLC. the controller is licensed for 12 AP's. I have plugged 8 AP's into the wireless vlan and 6 out of 8 come up with IP address and connect to the controller, broadcast two configured SSID's all seems good with them, but i have two AP's that do not get IP addresses. they are in the correct vlan i can plug a laptop into the group of ports in the val and get an IP address. So it seems to be just the AP's that don't. if i look at the consol of the AP it says: Waiting for PHY to auto negotiate . then it say timed out and continues to "boot with errors" then it continues to complain that it has no ip address. I have rebooted a few times and changed ports, and patch cables.
View 3 Replies
View Related
