Cisco Application :: 6500 Cannot Communicate To Device

Jul 9, 2012

I have installed ANM 5.2 virtual appliance.I have an issue importing a Catalyst 6500 device.When I try to import it, I get the following error: Device discovery failed: Cannot communicate to the device.Authentication failure while attempting to connect. Verify the device type and credentials. I double verified and the credentials are correct.I user SSH version 2.I use the following special carachters in the password: "!" and space.I don't use enable password to connect to the 6500 device. The 6500 device has a privilege 15 username.In ANM, the enable password is a requirement so I just fill in the regular password.I think the issue is appearing due to one of the following:
 
1.) The ANM does not support the special carachters I use in the 6500 password.

2.) Then ANM requires enable password, while I don't use enable password in the 6500 switch.
 
The 6500 runs SXI6 software version.I can't configure an enable password or configure a test username without special carachters beacause it's against the organization's policy.

View 1 Replies


ADVERTISEMENT

Cisco Firewall :: 6500 Can Shutdown Vlan1 On Switch And Still Communicate With FWSM

Jun 17, 2012

It is my understanding that the FWSM for the 6500 series switches uses a 6 port Etherchannel on the backplane to communicate with the 6500 series switch.Can you shutdown vlan1 on the switch and still communicate with the FWSM? I was under the impression that you could not (although I am looking at a config with it shutdown)

View 1 Replies View Related

Windows Cannot Communicate With The Device Or Resource

Feb 22, 2012

Windows cant communicate with the device or resource(primary dns server). The device or resource is not responding to requests.

View 4 Replies View Related

Windows Cannot Communicate With Device Or Resource?

Aug 7, 2012

I have had clearwire for a few years, about 2 months ago the internet started being weird. It would go slow, only load part of a page or disconnect completely. Now I cant get on at all. Not with my HP laptop, not with my daughters iPad, my husbands HP, ipod and not even if I hook up directly to the router. I have gone through 3 modems and 2 routers trying to fix this, but nothing has changed. When I run a trouble shooter, under "Problems Found", it says, "Windows cannot communicate with the device or resource. (primary DNS server)" I am currently on my computer at another location, every device we have, can get on the internet at other locations.

View 1 Replies View Related

Windows Can't Communicate With Device Or Resource

Jan 3, 2012

I am trying to set up my computer with my old connection. I use my laptop (acer aspire 5742ZG) and before I moved out it worked like it should have. Then while in the other town I needed to set up my connection, this time by myself (through some sort of interface in 192.168.1.1). Now that I'm back next thing happens: I appear to be online, I am online on skype (can chat, and people chat back) but when it comes to connecting to the internet through the browser or an online game I play it's not responding, as if there is a problem.I use windows 7, so the troubleshooting software reports what's in the title.The problem is not with the connection - 3 computers are connected to it, 2 with cable, 1 wireless. I would use wireless too, but I am too far away from the modem (it's in another house, and I have a long cable which works, posting from the desktop computer connected to it). [Code]

View 8 Replies View Related

SUS NB K52f/k62f - Can't Communicate With Device Or Resource

Jan 16, 2013

I have a ASUS NB K52f/k62f series, 3GBRAM intl Pentium CPU2.13GHz 500GB HD 392GB free, windows 7 home premium 64bit. wireless network connection: Atheros AR9285 Wireless Network Adapter

I am able to connect to the internet via Ethernet but I cannot connect via wifi. Its been work fine for 3years now but now its not able to connect to any network and all my other devices are able to connect just fine to these networks fine. The error message I get is Windows can't communicate with the device or resource (primary DNS server). so far I have disable and re enabled the wireless connection, reset the TCP/IP, went through properties of ipv4 and 6 and set them to obtain an ip address automatically, and system restore from when I was able to connect via wifi still not luck

View 14 Replies View Related

D-Link DIR-655 :: Windows Can't Communicate With Device Or Resource

Oct 9, 2011

Problems have arisen since purchasing a new laptop with Windows 7.  The problem seems erratic.  The laptop connects to file servers on the network, but often cannot connect to the network.  If it connects, often connection is lost when clicking to a new page.Usual error message:  "Windows can't communicate with the device or resource (primary DNS server)"Network  map shows communication lost between ADSL and network.Direct Hard wire connection to internet through ADSL works without issue.  Hardwire connection through DIR-655 same as wireless: erratic, error messages.  This message posted from another wireless router, specifics not known, connected without issue, on-line for 3 hours without problems.

-IP address: no difference between using automatically obtained or assigned IP address

-DNS server: no difference between using automatically obtained or assigned IP address

Router setup numerous times using CD ROM set up program.Firmware updated to the most recent version.Gone to tech support several times; can get the PC to connect and once done, tech support says its working only to disconnect within a few minutes.What must I do to get this DIR-655 router working on a regular basis?

View 7 Replies View Related

Cisco Application :: 6500 - ACE Compatibility With F5 GTM?

May 9, 2012

We have cisco ace 30 modules installed in cisco 6500 switches. For application availability purpose from the internet, we need to have some global site selector/3rd party devices with similar feature set that of cisco gss.
 
whether cisco ace is compatible to ge tintegrated with other 3rd party devices like F5 GTM?

View 1 Replies View Related

Cisco Application :: IOS Upgrade For ACE10-6500-K9

Oct 14, 2011

I have ACE10-6500-K9 installed in 6513 core switch with below mentioned sh version.
 
Software
loader:    Version 12.2[121]
system:    Version A2(2.0) [build 3.0(0)A2(2.0)]
system image file: [LCP] disk0:c6ace-t1k9-mz.A2_2_0.bin

[Code].....
 
I want to know that can i upgrade ACE10-6500-K9 to c6ace-t1k9-mz.A5_1_0 i.e version5 ? I tried to search cisco website but could not get proper upgrade or user guide.

View 2 Replies View Related

Cisco Application :: 6500 / How To Display CSM Uptime

Sep 12, 2012

I have done this in the past but I cannot find it anywhere......how do you display the uptime of a CSM module in a 6500? The chassis has an uptime of over 2 years, but I believe the CSM module was power cycled at some point within that 2 years and I need to find out if we may be running in to the bug that occurs after 828days of uptime. We are running 4.2(6) on the CSM and 12.2(18)SXF1 IOS on the SUP.

View 3 Replies View Related

Cisco Application :: To Create A Static Bidirectional Nat On 6500

Jul 20, 2011

First of all, I want you to know that I do understand that it's not a good design at all, but I still need to implement it.My ACE20 in 6500 works in routed mode with VLAN 101 (10.0.101.0/24) as the client-side VLAN. I therefore have Vlan101 SVI (10.0.101.1/24) on 6500.I also have VLAN 200 (10.0.200.0/24) on 6500 with SVI Vlan200 (10.0.200.1/24) and I want to create a static bidirectional NAT so that clients, connecting to IP address in VLAN 200 (10.0.200.64) would be NATed to VIP (10.0.101.10).Let's say we have clients (10.0.500.0/24) connecting through gig1/0/1.Here is my current setup on 6500.

View 14 Replies View Related

Cisco Application :: Asymmetric Routing Seen In WAE When Using 6500 Switch?

May 23, 2011

When we do self diagnostic test for WAE connected to the 6500 switch i get warning as below. Due to this alert there is no major acceleration benfits by the WAAS
 
Test WARN  [tfo] WARN  ASYMMETRIC  Asymmetric routing is seen in the device Action:  Check router's network configuration and WCCP redirection on the router.usevwa1#
 
6509 switches has only L2 capability and does not do WCCP redirection. The WCCP re-direction is done by 2821 routers.Is there any command which needs to be given in 6500 switch to solve the issue

View 1 Replies View Related

Cisco Application :: ACE SM Indexing In A Catalyst 6500 VSS Environment

Mar 7, 2013

I was asked to mount ACESMs on each of the CAT6K switches of a VSS cluster (one ACESM on each individual switch).On a non-VSS environment, the "svclc module <slot> vlan-group <group>" command is used to bind the VLAN group to the module on a certain slot. But now I am facing a VSS scenario, I will need to combine switch and slot in order to reference each of the individual modules...
 
How do I "index" each of the ACESMs in a VSS cluster? ¿Is there an extension of the aforementioned command to be able to combine switch and slot information?

View 1 Replies View Related

Cisco Application :: ACE10-6500-K9 Supporting C6500 IOS

Dec 7, 2011

It seem that ACE10 not support 12.2(33)SXJ1 IOS running on C6500. The box cannot detect the ACE module when power up. Currently the ACE10 running on system A2(30).
 
My challenge i have the ASA SM that compulsary to run on 12.2 (33) SXJ1 version. How to let these 2 module can running on the same C6500 box?

View 1 Replies View Related

Cisco Wireless :: WLC 5508 Can't Communicate To Wireless Device

Aug 8, 2012

i have a wlc 5508 with code 7.0.220, with multicast enabled in it and on the lan too.I am having a bit of confusion getting bonjour to work on the wireless side. Looking at some of the cisco docs, i still have some questions on how to get it working in my specific enviroment.
 
I have the wlc conected to the lan via a port-channel.  2 wlan (ssid1 and ssid2) each wlan maps to a specific vlan (dynamic int), the management int (also used for dynamic ap-manager) on a third vlan (vlan x).
 
I need to get Bonjour working between ssid1 and vlan-x, so my wireless clients (in ssid1 can use bonjour with their laptops) can synch between wireless and wired. I know that you can do this within the same wlan (ssid) but in this case, when a user has a laptop wired into the network he cant comunicate to the wireless device. I read about Vlan Select and Multicast Optimization however, from what i understand i need to setup an interface group and just assign my wlan1 and management int to it, correct?

when or if i need a different segment (vlan y) in my lan to also "bonjour" with ssid1? For this i assume i would need to create a dynamic interface on the wlc using the same IP segment and do the a new interface group?

View 5 Replies View Related

Cisco Application :: Configure New ACE 30 Module On Top Of 6500 Core Switch

Jan 12, 2013

i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?

View 1 Replies View Related

Cisco Application :: Password Recovery For ACE Service Module 6500

Dec 27, 2011

I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?

View 2 Replies View Related

Cisco Application :: ACE And FWSM Design And Configuration Guideline With 6500

Apr 8, 2013

I have Cisco 6500 with FWSM and ACE module which are in one central DC. Also we have four different Datacenter (Hub & spoke) and in our FWSM we have configured four contexts in central DC FWSM for each DC. Each DC servers are different VLAN and IP subnet. Now we have to configure ACE module for load balancing among those different subnet servers. What will be the design and configuration for this solution? Like routed or one-arm mode design.
 
Scenario Example:
1.  App Server01
IP:192.168.11.5/24
GW: 192.168.11.1 in FWSM
FWSM Context: DC1
Physical Location:DC1
VLAN:11

[code].....
 
Now customer requirement is we have to load balance using ACE between these App Servers which are in different context s in FWSM and one Server is not FWSM. how to configure or design or placement of ACE and FWSM for above scenario.

View 4 Replies View Related

Cisco Application :: Failover ACE / Default Route Redundancy / 6500

Jun 20, 2011

Since the ACE supports only static routing, when pointing a default route from the ACE what is your preferred method when using multiple 6500s with an ACE in each in a failover scenario to prevent just pointing at one 6500? Static route to an HSRP address? Multiple static routes on the ACE, etc?

View 2 Replies View Related

Cisco Application :: ACE10-6500-K9 / How Static Entry Under Sticky Performs

Jul 26, 2011

how a static entry under a "sticky" performs Configuring Static IP Address Sticky Table Entries Cisco Documentation Says When you configure a static entry, the ACE enters it into the sticky table immediately. Configuring the ACE Action on Server Failure failaction purge # The purge keyword specifies that the ACE remove the  connections to a real server  if that real server in the server farm  fails after you enter the  command. The ACE sends a reset (RST) to both  the client and the server  that failed. Cisco Documentation Says If you do not configure this command, the ACE takes no action when a server fails
 
sample config
sticky ip-netmask 255.255.255.240 address source STICKY1
timeout 180   replicate sticky   serverfarm SERVERFARM1   8 static client source 192.168.12.15 rserver SERVER1
  
Question1 - What happens if SERVER1 fails?
 
a) Does the ACE let the connections to SERVER1 timeout(default behaviour) and then load-balance new connections coming in deom 192.168.12.15 to another server in SERVERFARM1

ORb)  Does the ACE reset the connections to SERVER1  immediately and starts  load-balancing new conenction coming in from  192.168.12.15 to other  servers in SERVERFARM1 ?

ORc) Does the ACE just drop the current and new connections from 192.168.12.15 till SERVER1 comes back up ?

OR d) Is it dealt differently?
 
Question2 - Now what happens if the failed server(SERVER1) comes back up after some time?
 
e) Does the ACE reset any current connections from 192.168.1.15 and starts sending them to SERVER1 ?

ORf)  Does the ACE leave the current connections from 192.168.1.15 to other  servers in SERVERFARM1 as they are and send any new connections
from 192.168.1.15 to SERVER1?

ORg) Is it dealt differently?
 
My guess is Question1 -> a) and Question2 -> e)
 
ACE model =  ACE10-6500-K9
Version =  A2(3.3) 

View 4 Replies View Related

Cisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst

Apr 12, 2012

Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?

View 1 Replies View Related

Cisco Application :: ANM 5.2.1 Device Down False Alarms?

Jan 5, 2013

Facing false alarm issues with ANM 5.2.1. Basically ANM is sending device down (ACE-30 module) messages occasionally, but in real the device has never went down.
 
Message:
 
ANM Server Host Name        : anm-1
ANM Server IP Address        : 10.9.20.1
Device ID                              : AGG-B:3
Component Name                  : AGG-B:3
Severity                               : info

[code]....

View 7 Replies View Related

Cisco Application Networking :: How To Setup New ACE 4710 Device

Mar 17, 2013

I need to setup new ACE 4710 device , after referring to "Establishing a Console Connection on the ACE" i had managed to set up initial console connection.   During installtion i had configured vlan (default vlan 1000) , interface ip adess& subnet mask.
 
Post initial config i understand i should be able to open' Device Manager GUI Login Window' but it is not opening.I  also need inputs on setting 4710 for the telnet connection

View 4 Replies View Related

Cisco Application :: Does 6500 SUP720 / 2T Support MAC Address-Table Move Update Feature

Apr 21, 2013

Does 6500 SUP720/2T support MAC Address-Table Move Update Feature?

View 1 Replies View Related

Cisco Application :: ACE 4710 Sync Fail From Device Manager?

Aug 18, 2011

I am getting sync fail on device manger A3(2.2) to ACE 4710 appliance when I am changing certificate in one of proxy service.

View 1 Replies View Related

Cisco Application :: ACE30 Accessing Appliance Device Manager

Sep 6, 2011

I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool.  I don't see a GUI as detailed in the document: url...How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?Having read through copious amount of documentation I can't seem to find a refrence that would ne useful here.  This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?

View 2 Replies View Related

Cisco Application :: 4710 - Device Manager On Primary ACE Cannot Authenticate

Nov 4, 2012

In a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
 
CH01AC03/P-115-A# sh ft group summary
 
FT Group                     : 14
Configured Status      : in-service
Maintenance mode : MAINT_MODE_OFF
My State                     : FSM_FT_STATE_ACTIVE
My Config Priority       : 200

[code]....

View 2 Replies View Related

Cisco Application :: ACE 4710 Device Manager ERROR In Loading Configuration

Nov 20, 2012

When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
 
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
 
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.

Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.

-When I'm logged on to the GUI, the above message is displayed in the status bar always.

-It was not recovered by ACE restart it.

-When I try to create the same configuration in a different environment, it did not reproduce.

View 2 Replies View Related

Cisco Application :: ACE 4710 License Installation Failed With No Space Left On Device

Jan 15, 2012

The installation of an ACE-4710 throughput upgrade license licence (ACE-AP-02-UP1) failed with an error message :CH01AC03/Admin#  license install disk0:ACE20111213081741975.lic.Installing license... failed: No space left on device. [code]

View 4 Replies View Related

Dell :: XPS Studio 7100 - Bluetooth Application Or Drivers Do Not Show Up In Device Manager

Nov 4, 2012

I did a clean install of windows 8 and my tooth application or drivers do not show up in device manager dell xps studio 7100.

View 1 Replies View Related

Cisco Switching/Routing :: Upgrade 6500 Non Modular IOS To Normal 6500?

Dec 21, 2011

how can we upgrade 6500 non modular ios to normal 6500 ios?

View 5 Replies View Related

Cisco Application :: ACE20 - Config Application In Progress Message

Dec 3, 2012

Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
 
If I run show download info, I get:
 
context : context1
Interface                     Download-status
--------------------------------------------------------------
187                         In Progress
199                             Pending
 
Regex download optimization status : Couldn't get status[TNRPC Timed out]
 
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].

View 2 Replies View Related

Cisco :: LMS 3.2 Failed To Start Acquisition / Device Unreachable / Enter A Valid Device

Jan 3, 2013

We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved