Cisco Wireless :: Successfully Deployed WGB With 5508 WLC?
May 21, 2013
How to successfully deployed a WGB with a 5508 WLC?5508 code is 6.0.202.0 and the WGB is an AP1131AG?The documentation is ambiguous in that it states you can't use VLANs and then shows VLANs being used.I have a WLAN called wgb-link set up on the WLC with WPA-2 AES and PSK. The WLAN points to a logical interface called wgb-link which is configured to be in VLAN 9 and the default gateway is the VLAN SVI on the core switch.On the WGB I have configured the same SSID and security setup.
I am using the 5GHz radio and have set it to be a work group bridge.I have a sub interface dot11radio 1.9 configured:
encapsulation dot1q 9 native
bridge group 1
I also have an ethernet sub interface configured:
encapsulation dot 1q 9 native
bridge group 1
Int BVI1 is configured with an IP address in VLAN 9.The WGB links up fine and I can see it as a client on the WLC.
From the WGB CLI I can ping the interface on the WLC and the SVI on the core switch and any other device on the network in any VLAN.From the WLC I can ping the BVI1 address of the WGB.From the core switch I can ping the WLC interface and the WGB BVIi interface.
If I connect a laptop to the WGB ethernet port with a static IP address in VLAN 9 I cannot ping from the laptop to the WLC interface or the SVI on the core. I can only ping to the BVI address of the WGB.
Issue 1: I have been trying to configured Webauth bundle however it seems that is not working.
1. login.tar created use picozip contains 3 files: login.html, terms.html, and logo.jpg. 2, uploaded via FTP to controller successfully.. 3, no issue when i tried to preview on the controller
However users unable to see the login page when connected to guest wifi. when the user tried to connect cisco.com, on the browser address shows that the page redirected to url... however internet explorer / firefox display "Connection reset error".During this time, if i ask the user to type url... they can see the default login page, so no issue on connectivity to the service port.
Issue 2: Since i couldnt make that work, i have use default webauth internal. its all good. then when i tried to upload customlogo.jpg (18k size). User able to see the login page however not the logo. it shows broken image icon on the web browser. --> i can see the logo when i did preview on the controller.
Issue 3: last resort if i couldnt get the answer by sunday, how do i delete or remove the customlogo ?? so by monday users will not be seeing any errors on the page.
I have deployed a number of AIR-LAP1142N-E-K9 access points at a site, but I have an issue where all access point have defaulted to Channel 1. I have set the perameters on the Lightweight AP Template correctly to allow dinamic power and channel selection. The positioning of the AP's are as per the WCS planning tool.
Can a Cisco PIX 515E with an Unrestricted License (UR) be deployed as a VPN concentrator? For example, remote users having VPN clients installed on their desktops connect through the Internet and are authenticated by the PIX 515E at the main site.
I have recently purchased 2 x 1941 routers with 2 L-SL-19-SEC-K9= and 2 L-FL-SSLVPN10-K9= licenses. I've installed the licenses through Cisco Configuration Pro ver 2.5 and installation did not generate any errors. After saving config and reloading the device, on the License dashboard, the deploy status for the SSL VPN is "Not deployed" and I have no way of deploying it. The state also says "Active, Not in use". I have tried reinstalling the license via command line but get error "license duplicate - already installed" suggesting the installation was OK. The sec license deployed without any issues. Is there any way to manually deploy this SSL_VPN license?
I'm using LMS 4.0.1, migrating data from 3.2. When I select My menu, My dashboards, Functional (or any other view) I can get a list of non deployed port lets.
I recently had to wipe (start all over again) my fathers PC as it become infected with a virus which I struggled to remove. When trying to set up the wireless connection via my virgin wireless manager I followed all the steps correctly until the last where it could not find my USB wireless adapter. I installed the latest software for the adapter from the netgear website but it will still not succesfully install the drivers fro the adapter.
Region : United Kingdom Model : TD-W8960N Hardware Version : V3 Firmware Version : ISP : ADSL24
How to successfully get VPN passthrough working with the W8960N?
I have the W8960N providing internet to local device. I want to setup a second router, TP-Link 1043ND with WW-DRT and PPTP set up to provide a separate access point for PPTP tunnelling to VPN servers outside of the UK. HideMyAss are providing VPN servers I wish to connect to.
I have followed instruction to set up both routers but would like to know if I am missing something. First router 192.168.1.1 is basically untouched but with ports under NAT added: ports 1723 and 47 for my second router at local IP 192.168.1.111 Second router is set up according to [URL].
I know VPN work via just my first router. I can tunnel through using an Android tablet and connect to any HMA VPN server without changing anything on the 8960N.
Region : France Model : TL-WR841ND Hardware Version : V8 Firmware Version : 3.13.27 Build 121101 Rel.38183n ISP : Orange
I am wondering if it is worth switching to OpenWRT firmware for my TL-WR841N V8.0 ..Has anyone successfully switched to OpenWRT Attitude Adjustment Release (12.09) ? If so are you happy with the features and stability provided ? I checked for the Gargoyle firmware, and t seems there are still some issues with TL-WR841N release 8.0 ... Therefore I am not considering this alternative firmware for now.
currently using Linksys Cisco E2000 ,Firmware 1.0.04.Trying to few block sites from Access restriction - bellow is the screen shot its not working. I have alos enabled SPI Firewall from Security Tab. how could I block site successfully.
I've been using a WRT150N wireless router successfully up until a couple days ago, when it stopped being detected. I can plug my computer directly to my modem, and it works, so my internet connection is fine. I have an older BEFW11S4 router that I am using currently, but it is very slow compared the the N router. I've tried resetting the 150N router, and also the modem, and combinations of both, but nothing seems to work. I plugged the router into my computer without connecting the modem, but I'm not able to access 192.168.1.1 either. All the lights illuminate when the router is plugged in.
No matter what I do, whenever I enter the Web Interface for my E4200, the page comes up in Russian (at least I think it is russian!!)! I have changed the language to English (by trial and error discovered it was the first option at the top of the pull-down list) many times and yes, selected save at the bottom of the Setup page. I get the message back "Your settings have been successfully saved".But next time I go in, it is back to either Russian or sometimes some other wierd script, and I have to reselect English.
I have a Linksys Wireless G PCI adapter. The model is WMP54gs and the serial number MGP00E416793. I am trying to install this adapter on a Windows XP media center computer. The computer is update to date with all windows updates. I need the driver and software to successfully get this adapter to fully work.
I have PAT set up successfully on 6506 chassis - My outside address range is 78.24.112.114 255.255.255.240.Relevant parts of the config below: [code] This works fine but of course is only using the one IP address 78.24.112.114.how I can utilize the other outside addresses available or is this not really necessary? I've browsed through loads of Cisco docs.
I bought a CISCO SG200-18 switch. I added the Switch to my LAN and started the Switch (as described in the manual). The Switch starts the booting procedure (green blinking status LED) After a while, the LED starts to blink orange and green, instead of steady green.
In generally the Switch seems to work. I can access my whole network, but not the web interface of the switch itself. I also can't see the switch in the ADSL / DHCP rooter.
I also tried to boot the switch only connected to the PC. But ping on 192.198.1.254 is not working. The switch is in the same subnet like my other LAN components.
I am trying to set up a site to site VPN tunnel using GRE over IPSEC. Below is the configuration from both routers and debug output. I'm scratching my head on this one. I'm using two Cisco 7600 routers with SSC-400 SPA modules and 720 Supervisors. The IOS on R1 is 12.2 SXI2 and R2 has 12.2 SXI3.
I have been trying to block access to Steam and Left 4 Dead 2 on a specific computer, using the correct listed ports and using the port forwarding section of the router (setting the access to deny) however they seem to still be able to access both steam and L4D2 on their computer.how I can still block the access?
How to successfully configure and connect to a DynDNS account with RVS4000? This was working fine for me until recently when I think I upgraded the firmware to 1.3.3.5.I am trying to connecting to DynDNS.org service. In the past, I used the following string for the Hostname which worked:'mysubdomain.domain.com&system=custom' (including small quotes)According to the RVS4000 documentation, all you should have to do is specify the host name with DynDNS but this clearly is not accurate.
Ok on my new PC,,OS is windows xp..I works fine..connect to pppoe and can surf internet perfectly.But on my old pc,,it can only succesfully connect to wan miniport pppoe but cant surf the internet..its OS is Windows Vista home Prem.The old pc was my first pc(notebook) and last time I used it was on 2009..it was using Atheros AR8131 PCI-E Gigabit Ethernet Controller connection and I forgot what modem I used..but now I bought TP-link TD-W8901G and I use for ADSL connection.My new pc works fine because it was setup proffesionaly by my friend..it also still needs Atheros AR8131 PCI-E Gigabit Ethernet Controller connection to connect ADSL Wan Miniport PPPoE..but I repaired my old pc too late..and he didnt configured it..so I setup myself..all the PPPoE adsl connections.And so its succesfully connected to WAN miniport PPPoE..but I can surf the internet..The old pc also needs Atheros AR8131 PCI-E Gigabit Ethernet Controller connection for me to connect ADSL Wan Miniport PPPoE..but all that was succesfull.
I have successfully connected my vpn to my central point and 2 branches.My branch can see central and visa versaMy problem is that i can't see from my 1 branch the other branch.
My central has RVS4000 and my branches has WRV200.How can i be able to access from my branch1 PC, my branch2 PC and visa versa
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY *Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00 00.0000.0000) *Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth ernet0, changed state to up *Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
I have a WLC5508 with around 70 AP's (LAP1042N) connecting over an MPLS WAN network. WLC and AP's are running 7.4.100
From time to time I have an AP which disassociates from the WLC with the logging beneath. This is a problem with the AP, or is this due to network saturation between the AP and the WLC ?
And if so, should I change the default retransmit values ?
I am planning to upgrade WLC from 7.2.103.0 to 7.2.110.0 due to some bug, but I wanted to know if it is compatible with WCS - 7.0.240.0 and NAC Guest server version 2.1.0, I am made some search but I couldn't get to proper conclusion.
I have a wlc 5508 running version 7.0.116.0 that I need to uppgrade to use the CAP2602I AP. I understand that I need to upgrade it to version 7.0.240 before 7.4.100 to avoid loosing HREAP VLAN mappings, and I have also read that i need to install the FUS image [URL]. In what order should this be done? Shlod the FUS image be installed before new firmware ore after firmware or after 7.0.240 but before 7.4?
since few weeks i configure my APs on the new WLC5508, and then, the lights are off on the AP, is it normal? however they seems to work fine. What does this light means? FW version: 7.0.22,Is it important?
In order to enbale HA SSO on our two 5008 WLC's, I plan to upgrade them to 7.3 / 7.4 (currently 7.2)Right now 7.3.112.0 is the latest release. We do not have any 1600 series AP's, which requires 7.4.any reason going for 7.4 directly..or not going for it?
I am trying to setup SSO between my primary and secondary 5508 controller, and it doesn't appear to be working. I lose connection to both devices after the reboot and then have to console in and disable redundancy manually to regain connectivity. Is there something special required for this to work that isn't apparent?
